Featured
The ESP32-S3 has arrived in QT Py format - and what a great way to get started with this powerful new chip from Espressif! With dual 240 MHz cores, WiFi and BLE support, and native USB, this QT Py is great for powering your IoT projects. Now we even have this powerhouse of a board with built...
view other guides that use this product
$12.50 each
In Stock
Featured
The LIS3DH is a very popular low power triple-axis accelerometer. It's low-cost, but has just about every 'extra' you'd want in an accelerometer:Three axis sensing, 10-bit...
view other guides that use this product
$4.95 each
In Stock
Featured
Is your QT Py all alone, lacking a friend to travel the wide world with? When you were a kid you may have learned about the "buddy" system, well this product is kinda like that! A board that will watch your QT...
view other guides that use this product
Out of Stock
Featured
Lithium-ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light, and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 400mAh for a total of about 1.9 Wh. If you need a larger (or smaller!)...
$6.95 each
In Stock
UGlu Dashes are perfect for a variety of small projects. These adhesive squares provide a stronger bond to most surfaces and are cleaner and easier to remove without the wait, mess, or hassle.Adheres to a wide variety of surfaces, including, but not limited...
$0.95 each
In Stock
Featured
This is the easiest way possible to add small, bright RGB pixels to your project. We took the same technology from our Flora NeoPixels and made them breadboard friendly, with two rows of 3 x 0.1" spaced header on each side for easy soldering, chaining and breadboarding. These ultra-bright...
view other guides that use this product
Out of Stock
This 4-wire cable is 50mm / 1.9" long and fitted with JST SH female 4-pin connectors on both ends. Compared with the chunkier JST PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove.
$0.95 each
In Stock
Our QT Py boards are a great way to make very small microcontroller projects that pack a ton of power - and now we have a way for you to quickly add a strand of NeoPixels with a 5V level shifter and a detachable JST PH connector. It's an...
view other guides that use this product
$3.95 each
In Stock
Plug in and glow, this Adafruit NeoPixel LED Strip with JST PH Connector has 30 total LEDs in a "60 LED per meter" spacing, and is 0.5 meters long, in classy Adafruit Black. Its not too long, but has lots of glowing action.
view other guides that use this product
Out of Stock
This cable is a little over 100mm / 4" long and fitted with JST-PH 3-pin connectors on either end. We dig the solid and compact nature of these connectors and the latch that keeps the cable from coming apart easily. We're carrying these to
$0.75 each
In Stock
Breakaway header is like the duct tape of electronics, and this header is one better with extra long pins on both sides. This makes it great for connecting things together that have two sockets - especially solderless breadboards. We also...
$3.00 each
In Stock
Female header is like the duct tape of electronics. Its great for connecting things together, soldering to perf-boards, sockets for wires or break-away header, etc. We go through these guys real fast, and thought that given how handy they are, we'd offer them in a pack of five!
Out of Stock
Featured
Like Missy Elliot, we like to "put our [Feather] down, flip it and reverse it" and that's exactly what we've done with this new development board. It's basically our
view other guides that use this product
$24.95 each
In Stock