This incredibly small stereo amplifier is surprisingly powerful - able to deliver 2 x 3.7W channels into 3 ohm impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.7V-5.5VDC. Since the amp is a class D, its incredibly efficient (over 90% efficient when driving an 8Ω speaker at over a Watt).
This amplifier is perfect for portable and battery-powered projects. It has built in thermal and over-current protection, but you really have to drive it hard before it even gets warm! This board is a welcome upgrade to basic "LM386" amps!
This amplifier is perfect for portable and battery-powered projects. It has built in thermal and over-current protection, but you really have to drive it hard before it even gets warm! This board is a welcome upgrade to basic "LM386" amps!
Specifications:
- Output Power: 3.7W at 3Ω, 10% THD, 1.7W at 8Ω, 10% THD, with 5V Supply
- Passes EMI limit unfiltered with up to 12 inches (30 cm) of speaker cable
- High 83dB PSRR at 217Hz
- Spread-Spectrum Modulation and Active Emissions Limiting
- Differential Inputs
- Five pin-selectable gains: 6dB, 9dB, 12dB, 15dB and 18dB. Select with a jumper or by setting the G and G' breakout pins (see schematic for breakout board showing gain pin settings for details)
- Excellent click-and-pop suppression
- Thermal and short-circuit/over-current protection
- Low current draw: 2mA quiescent and 10uA in shutdown mode
What is a Class D Amplifier?
A Class D Amplifier uses PWM to generate high-frequency square waves with a duty-cycle proportional to the voltage level of the input audio signal. By minimizing the transition time between fully on and fully off, the MOSFET drivers are able to operate at a very high efficiency. Class D amplifiers such as this one typically operate at over 90% efficiency, compared to efficiencies of 50% or less for typical class AB amplifiers.
The high frequency square-wave component of the output signal is filtered by the inductance of the speaker voice coil, leaving only the amplified audio signal.
Other Audio amps available at Adafruit
We have a few choices of audio amplifiers, here's how you can compare them
-
MAX98306
- This class D audio amplifier has selectable gains of 6dB, 9dB, 12dB,
15dB and 18dB that you can choose with a jumper. It can do up to 3.7W
into 3Ω, 2.8W into 4Ω and 1.7W into 8Ω. However, you cannot shut down
each speaker separately. Its a good choice where you don't mind setting
the gain with a jumper and if you do not need to ever turn off only one
audio channel and you do not need more than 18dB. Its an excellent
amplifier that can driver down to 3Ω speakers
Like the TS2012, it has differential inputs, bridge tied outputs, and can run from 2.7V to 5.5V
-
TS2012 - This class D audio amplifier has selectable gains of 6dB, 12dB,
18dB and 24dB that you can choose with a jumper (the MAX98306
goes up to 18dB only). It can do up to 2.8W into 4Ω and 1.7W into 8Ω. It
cannot drive 3Ω. You can shut down each channel separately. Setting the
gain is easy on the onboard DIP switches. Its a good choice where you
don't need to drive 3Ω speakers or if you ever want to turn off only one
audio channel. If you need 24dB gain this amp can do it.
Like the MAX98306, it has differential inputs, bridge tied outputs, and can run from 2.7V to 5.5V
Text editor powered by tinymce.