# Raspberry Pi Zero Stand

## 3D Printing

https://www.youtube.com/watch?v=-UtztGH0N7M

## Pi Zero Projects

Display your Pi Zero on your desk with this simple yet useful stand.  3D prints in one piece and doesn't require any supports. It features mounting holes for securing a Pi Zero. A hole in the stand allows for wires to pass through for USB power and peripherals.

![3d_printing_hero-laptop-angle.jpg](https://cdn-learn.adafruit.com/assets/assets/000/071/025/medium640/3d_printing_hero-laptop-angle.jpg?1549911229)

## Pi Bonnets, Hats and Add-Ons

There's heaps and heaps of accessories for the Raspberry Pi Zero, from touchscreen and displays to HATs, and Bonnets, there's something for your project! Check out all the goodness Adafruit shop has to offer! Use the link below or just use the search bar.

![3d_printing_hero-bonnets.jpg](https://cdn-learn.adafruit.com/assets/assets/000/071/044/medium640/3d_printing_hero-bonnets.jpg?1549985290)

[Adafruit Pi Bonnets](https://www.adafruit.com/category/929)
## Parts & Hardware

A Pi Zero W, microSD card and microUSB cable is about all you need for this project. You can grab one of the [Pi Zero Kits](https://www.adafruit.com/product/3411) to get you going. You'll also need additional hardware to secure the Pi Zero W. Pi uses M3 mounting holes but you can use M2.5, we have a handy [M2.5 nylon standoff kit](https://www.adafruit.com/product/3299).

- 4x M2.5/M3 x 5mm female/male standoffs
- 4x M2.5/M3 x 5mm button head screws
- 4x M2.5/M3 hex nuts

![3d_printing_parts.jpg](https://cdn-learn.adafruit.com/assets/assets/000/071/033/medium640/3d_printing_parts.jpg?1549915649)

### Raspberry Pi Zero W Starter Pack - Includes Pi Zero W

[Raspberry Pi Zero W Starter Pack - Includes Pi Zero W](https://www.adafruit.com/product/3411)
Remember those cereal commercials that would always say, "part of a complete breakfast"? Well the Pi Zero's a lot like that bowl of cereal - while it's great on its own, you need a lot of accessories to make it a complete meal. 

The **Pi Zero W...**

Out of Stock
[Buy Now](https://www.adafruit.com/product/3411)
[Related Guides to the Product](https://learn.adafruit.com/products/3411/guides)
![Components included in a Raspberry Pi Zero W Starter Pack ](https://cdn-shop.adafruit.com/640x480/3411-02.jpg)

### Raspberry Pi Zero WH (Zero W with Headers)

[Raspberry Pi Zero WH (Zero W with Headers)](https://www.adafruit.com/product/3708)
If you didn't think that the Raspberry Pi Zero W could possibly get any better, then boy do we have a pleasant surprise for you! The new **Raspberry Pi Zero WH ** offers all the benefits of the Pi Zero W, but with one big difference – a **pre-soldered GPIO...**

In Stock
[Buy Now](https://www.adafruit.com/product/3708)
[Related Guides to the Product](https://learn.adafruit.com/products/3708/guides)
![Angled shot of Raspberry Pi Zero W computer with headers.](https://cdn-shop.adafruit.com/640x480/3708-00.jpg)

### Black Nylon Machine Screw and Stand-off Set – M2.5 Thread

[Black Nylon Machine Screw and Stand-off Set – M2.5 Thread](https://www.adafruit.com/product/3299)
Totaling 380 pieces, this **M2.5 Screw Set**  is a must-have for your workstation. You'll have enough screws, nuts, and hex standoffs to fuel your maker tendencies for days on end! M2.5 size screws fit almost all of the Adafruit breakout/dev board mounting holes...

In Stock
[Buy Now](https://www.adafruit.com/product/3299)
[Related Guides to the Product](https://learn.adafruit.com/products/3299/guides)
![Black Nylon Screw and Stand-off Set with M2.5 Threads, kit box](https://cdn-shop.adafruit.com/640x480/3299-00.jpg)

## 3D Model

The stand is a one piece design that does not require any support material. It's parametrically driven so the viewing angle, thickness and size can be easily modified by changing a parameter. Check out my [Layer by Layer tutorial](https://www.youtube.com/watch?v=B9O-rSiAJk0) on how I set that up using Autodesk Fusion 360.

![3d_printing_cad-explode.gif](https://cdn-learn.adafruit.com/assets/assets/000/071/035/medium640thumb/3d_printing_cad-explode.jpg?1549981194)

## Slice Settings

Use these settings as reference. Values listed were used in [Ultimaker's CURA 3.X](https://ultimaker.com/en/products/ultimaker-cura-software) slicing software.

- 0.2mm Layer Height / 0.4mm nozzle
- 0.38mm Line Width (inner & outer widths)
- 40mm/s printing speed
- 20% infill
- Supports: No

![3d_printing_cura-slice.jpg](https://cdn-learn.adafruit.com/assets/assets/000/071/032/medium640/3d_printing_cura-slice.jpg?1549915114)

[Download CAD Files](https://github.com/adafruit/Adafruit_Learning_System_Guides/tree/master/Pi_Zero_Stand)
## Design Source Files

The enclosure assembly was designed in Fusion 360. This can be downloaded in different formats like STEP, SAT and more. Electronic components like the board, displays, connectors and more can be downloaded from our [Fusion 360 CAD parts github repo](https://github.com/adafruit/Adafruit_CAD_Parts).

[Download Adafruit CAD Parts](https://github.com/adafruit/Adafruit_CAD_Parts)
[Fusion 360 Share Link](https://a360.co/2I9LVzz)
# Raspberry Pi Zero Stand

## Assembly

## Install Standoffs

Start by installing the M3 standoffs to the four mounting holes. Finger tightened them so as not to strip the holes. If you find the mounting holes are too tight, I suggest tapping using an M3 tapping tool to create threads.

![3d_printing_standoff-install.gif](https://cdn-learn.adafruit.com/assets/assets/000/071/036/medium640thumb/3d_printing_standoff-install.jpg?1549984138)

## Install Hex Nuts

Place the M3 hex nuts onto the male threads of the standoffs. Finger tighten at first and optionally use a pair of pliers to firmly tighten. Repeat for all four standoffs.

![3d_printing_hexnut-install.gif](https://cdn-learn.adafruit.com/assets/assets/000/071/037/medium640thumb/3d_printing_hexnut-install.jpg?1549984152)

## Install Screws

Grab four M3 x 5mm mertric screws and begin to fasten into the mounting holes on the Pi Zero board. The mounting holes might be tight so I suggest using an M3 screw tap to loosen up the holes and create proper threads.

![3d_printing_pi-screw-install.gif](https://cdn-learn.adafruit.com/assets/assets/000/071/038/medium640thumb/3d_printing_pi-screw-install.jpg?1549984165)

## Pi Zero Placement

Grab the Pi Zero PCB and place it on top of the standoffs. The USB and HDMI connectors should be oriented down towards the center hole in the stand.

![3d_printing_pi-standoff-place.gif](https://cdn-learn.adafruit.com/assets/assets/000/071/039/medium640thumb/3d_printing_pi-standoff-place.jpg?1549984180)

## Secure Pi

Fasten the four screws until fully tightened – Be careful not to over tighten as you could damage the PCB or strip the threading. 

![3d_printing_pi-screw-secure.gif](https://cdn-learn.adafruit.com/assets/assets/000/071/040/medium640thumb/3d_printing_pi-screw-secure.jpg?1549984202)

## Pi Check

How's everything looking? Rotate the stand and inspect all of the hardware.

![3d_printing_pi-installed.gif](https://cdn-learn.adafruit.com/assets/assets/000/071/041/medium640thumb/3d_printing_pi-installed.jpg?1549984216)

## Install Add-Ons

Press fit your bonnets, pHAT, display or add-on to your Pi Zero. 

![3d_printing_bonnet-press.gif](https://cdn-learn.adafruit.com/assets/assets/000/071/042/medium640thumb/3d_printing_bonnet-press.jpg?1549984230)

## USB Power

Cables can pass through the center hole near the bottom of the stand. HDMI cables are the most chunky but should pass through OK. However, an HDMI adapter on a cable might not have enough clearance to use properly. 

![3d_printing_usb-plug.gif](https://cdn-learn.adafruit.com/assets/assets/000/071/043/medium640thumb/3d_printing_usb-plug.jpg?1549984245)


## Featured Products

### Raspberry Pi Zero W

[Raspberry Pi Zero W](https://www.adafruit.com/product/3400)
If you didn't think that the Raspberry Pi Zero could possibly get any better, then boy do we have a pleasant surprise for you! The new **Raspberry Pi Zero W** offers all the benefits of the Pi Zero v1.3, but with one big difference – **built-in...**

In Stock
[Buy Now](https://www.adafruit.com/product/3400)
[Related Guides to the Product](https://learn.adafruit.com/products/3400/guides)
### Raspberry Pi Zero WH (Zero W with Headers)

[Raspberry Pi Zero WH (Zero W with Headers)](https://www.adafruit.com/product/3708)
If you didn't think that the Raspberry Pi Zero W could possibly get any better, then boy do we have a pleasant surprise for you! The new **Raspberry Pi Zero WH ** offers all the benefits of the Pi Zero W, but with one big difference – a **pre-soldered GPIO...**

In Stock
[Buy Now](https://www.adafruit.com/product/3708)
[Related Guides to the Product](https://learn.adafruit.com/products/3708/guides)
### Raspberry Pi Zero Budget Pack - Includes Pi Zero v1.3

[Raspberry Pi Zero Budget Pack - Includes Pi Zero v1.3](https://www.adafruit.com/product/2817)
Remember those cereal commercials that would always say, "part of a complete breakfast"? Well the Pi Zero's a lot like that bowl of cereal - while it's great on its own, you need a lot of accessories to make it a complete meal.

The **Pi Zero Budget...**

No Longer Stocked
[Buy Now](https://www.adafruit.com/product/2817)
[Related Guides to the Product](https://learn.adafruit.com/products/2817/guides)
### Raspberry Pi Zero W Starter Pack - Includes Pi Zero W

[Raspberry Pi Zero W Starter Pack - Includes Pi Zero W](https://www.adafruit.com/product/3411)
Remember those cereal commercials that would always say, "part of a complete breakfast"? Well the Pi Zero's a lot like that bowl of cereal - while it's great on its own, you need a lot of accessories to make it a complete meal. 

The **Pi Zero W...**

Out of Stock
[Buy Now](https://www.adafruit.com/product/3411)
[Related Guides to the Product](https://learn.adafruit.com/products/3411/guides)
### Black Nylon Machine Screw and Stand-off Set – M2.5 Thread

[Black Nylon Machine Screw and Stand-off Set – M2.5 Thread](https://www.adafruit.com/product/3299)
Totaling 380 pieces, this **M2.5 Screw Set**  is a must-have for your workstation. You'll have enough screws, nuts, and hex standoffs to fuel your maker tendencies for days on end! M2.5 size screws fit almost all of the Adafruit breakout/dev board mounting holes...

In Stock
[Buy Now](https://www.adafruit.com/product/3299)
[Related Guides to the Product](https://learn.adafruit.com/products/3299/guides)

## Related Guides

- [Arcade Bonnet Controller](https://learn.adafruit.com/arcade-bonnet-controller.md)
- [Planetary Gear Dreidels](https://learn.adafruit.com/planetary-gear-dreidels.md)
- [USB MIDI Host Messenger](https://learn.adafruit.com/usb-midi-host-messenger.md)
- [Wireless ESP32-S2 Touch Screen Controller for Pure Data](https://learn.adafruit.com/wireless-esp32-s2-controller-for-pure-data.md)
- [CircuitPython Elgato WiFi Light Controller](https://learn.adafruit.com/circuitpython-elgato-wifi-light-controller.md)
- [FunHouse IoT Fume Extractor and Air Quality Sensor](https://learn.adafruit.com/funhouse-fume-extractor-iot-air-quality-sensor.md)
- [Ambient Sound Machine](https://learn.adafruit.com/ambient-machine.md)
- [32x32 Square Pixel Art Animation Display](https://learn.adafruit.com/32x32-square-pixel-display.md)
- [Qualia S3 Compass](https://learn.adafruit.com/qualia-s3-compass.md)
- [Square NeoPixel Display with Black LED Acrylic](https://learn.adafruit.com/sqaure-neopixel-display-with-black-led-acrylic.md)
- [Compost Friend!](https://learn.adafruit.com/compost-optimization-machine.md)
- [PyPortal Wall Mount](https://learn.adafruit.com/pyportal-wall-mount.md)
- [CircuitPython OLED Watch Clock](https://learn.adafruit.com/circuitpython-oled-watch.md)
- [PyPortal Titano Weather Station](https://learn.adafruit.com/pyportal-titano-weather-station.md)
- [PicoDVI Adafruit IO Feed Dashboard](https://learn.adafruit.com/dvi-io.md)