# PyBadge Thermal Camera Case
## Overview
https://youtu.be/HIfdZp-G4lo
## Mini Thermal Camera
Build a mini thermal imaging camera with Adafruit PyBadge and MLX90640 IR Thermal Camera breakout. Record and analyze images for revealing the heat in circuits, machines and even humans!
## PyBadge & MLX90640
The IR thermal camera sensor uses the STEMMA QT connection so it easily plugs into the Adafruit PyBadge.
An external slide switch is used to power the circuit on and off. A metal ball button is used for reset.
A 3.7V 320mAh battery connects directly making this a portable project with rechargeable USB.
## Prerequisite Guide
This learn guide covers the 3D printing of the enclosure and assembly only. Follow the learn guides below to get the PyBadge board setup with code.
- [MLX90640 Thermal Camera with Image Recording](https://learn.adafruit.com/mlx90640-thermal-image-recording/overview)
[Learn Guide: MLX90640 Thermal Camera with Image Recording](https://learn.adafruit.com/mlx90640-thermal-image-recording)
## Parts
### Adafruit PyBadge for MakeCode Arcade, CircuitPython, or Arduino
[Adafruit PyBadge for MakeCode Arcade, CircuitPython, or Arduino](https://www.adafruit.com/product/4200)
What's the size of a credit card and can run CircuitPython, MakeCode Arcade or Arduino? That's right, its the **Adafruit PyBadge!** We wanted to see how much we could cram into a 3 3⁄8 × 2 1⁄8 inch rounded rectangle, to make an all-in-one dev board with...
Out of Stock
[Buy Now](https://www.adafruit.com/product/4200)
[Related Guides to the Product](https://learn.adafruit.com/products/4200/guides)
### Adafruit MLX90640 IR Thermal Camera Breakout
[Adafruit MLX90640 IR Thermal Camera Breakout](https://www.adafruit.com/product/4407)
You can now add affordable heat-vision to your project and with an Adafruit MLX90640 Thermal Camera Breakout. This sensor contains a 24x32 array of IR thermal sensors. When connected to your microcontroller (or Raspberry Pi) it will return an array of 768 individual infrared temperature...
In Stock
[Buy Now](https://www.adafruit.com/product/4407)
[Related Guides to the Product](https://learn.adafruit.com/products/4407/guides)
### Lithium Ion Polymer Battery with Short Cable - 3.7V 420mAh
[Lithium Ion Polymer Battery with Short Cable - 3.7V 420mAh](https://www.adafruit.com/product/4236)
Lithium-ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light, and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 420mAh for a total of about 1.55 Wh. If you need a larger (or smaller!) battery,
In Stock
[Buy Now](https://www.adafruit.com/product/4236)
[Related Guides to the Product](https://learn.adafruit.com/products/4236/guides)
### Breadboard-friendly SPDT Slide Switch
[Breadboard-friendly SPDT Slide Switch](https://www.adafruit.com/product/805)
These nice switches are perfect for use with breadboard and perfboard projects. They have 0.1" spacing and snap in nicely into a solderless breadboard. They're easy to switch no matter what size fingers you have, but not so easy that they'll get flipped by accident. Work great as...
Out of Stock
[Buy Now](https://www.adafruit.com/product/805)
[Related Guides to the Product](https://learn.adafruit.com/products/805/guides)
### Metal Ball Tactile Button (6mm) x 10 pack
[Metal Ball Tactile Button (6mm) x 10 pack](https://www.adafruit.com/product/3347)
Add some steely elegance to your project with these **Metal Ball Tactile Buttons**. They've got a nice industrial shine to them along with a light blue underbelly. Not only do they look good, but they're also good if you have an actuator that will be pressing the...
In Stock
[Buy Now](https://www.adafruit.com/product/3347)
[Related Guides to the Product](https://learn.adafruit.com/products/3347/guides)
### 4-pin JST PH to JST SH Cable - STEMMA to QT / Qwiic
[4-pin JST PH to JST SH Cable - STEMMA to QT / Qwiic](https://www.adafruit.com/product/4424)
Are you a maker in the midst of a [**STEMMA**](https://learn.adafruit.com/introducing-adafruit-stemma-qt/what-is-stemma) dilemma? This 200mm long 4-wire cable is a fantastic chimera-cable fitted with **STEMMA QT / Sparkfun Qwiic JST SH** on one end,...
In Stock
[Buy Now](https://www.adafruit.com/product/4424)
[Related Guides to the Product](https://learn.adafruit.com/products/4424/guides)
### Camera and Tripod 3/8" to 1/4" Adapter Screw
[Camera and Tripod 3/8" to 1/4" Adapter Screw](https://www.adafruit.com/product/2392)
_Whaddya got a screw loose or something?_
This **3/8" to 1/4"** **Adapter Screw** is super handy if you're building projects that connect to a tripod or a camera. It's a simple fix for getting a tripod with a 1/4" machine screw...
In Stock
[Buy Now](https://www.adafruit.com/product/2392)
[Related Guides to the Product](https://learn.adafruit.com/products/2392/guides)
### Part: Mini Tripod
quantity: 1
Portable folding desktop stand
[Mini Tripod](https://amzn.to/34RCiNB)
### Part: M2.5 Hardware
quantity: 1
M2.5 Screw and Nut Kit – 4x M2.5 x 16mm
[M2.5 Hardware ](https://amzn.to/3eN2WM3)
Featured
### Adafruit PyBadge for MakeCode Arcade, CircuitPython, or Arduino
[Adafruit PyBadge for MakeCode Arcade, CircuitPython, or Arduino](https://www.adafruit.com/product/4200)
What's the size of a credit card and can run CircuitPython, MakeCode Arcade or Arduino? That's right, its the **Adafruit PyBadge!** We wanted to see how much we could cram into a 3 3⁄8 × 2 1⁄8 inch rounded rectangle, to make an all-in-one dev board with...
Out of Stock
[Buy Now](https://www.adafruit.com/product/4200)
[Related Guides to the Product](https://learn.adafruit.com/products/4200/guides)
Featured
### 4-pin JST PH to JST SH Cable - STEMMA to QT / Qwiic
[4-pin JST PH to JST SH Cable - STEMMA to QT / Qwiic](https://www.adafruit.com/product/4424)
Are you a maker in the midst of a [**STEMMA**](https://learn.adafruit.com/introducing-adafruit-stemma-qt/what-is-stemma) dilemma? This 200mm long 4-wire cable is a fantastic chimera-cable fitted with **STEMMA QT / Sparkfun Qwiic JST SH** on one end,...
In Stock
[Buy Now](https://www.adafruit.com/product/4424)
[Related Guides to the Product](https://learn.adafruit.com/products/4424/guides)
Featured
### Silicone Cover Stranded-Core Ribbon Cable - 10 Wire 1 Meter Long
[Silicone Cover Stranded-Core Ribbon Cable - 10 Wire 1 Meter Long](https://www.adafruit.com/product/3890)
For those who are fans of our silicone-covered wires, but are always looking to _up their wiring game_. We now have **Silicone Cover Ribbon cables!** These may look _a lot_ like
Out of Stock
[Buy Now](https://www.adafruit.com/product/3890)
[Related Guides to the Product](https://learn.adafruit.com/products/3890/guides)
Featured
### Adafruit MLX90640 IR Thermal Camera Breakout
[Adafruit MLX90640 IR Thermal Camera Breakout](https://www.adafruit.com/product/4407)
You can now add affordable heat-vision to your project and with an Adafruit MLX90640 Thermal Camera Breakout. This sensor contains a 24x32 array of IR thermal sensors. When connected to your microcontroller (or Raspberry Pi) it will return an array of 768 individual infrared temperature...
In Stock
[Buy Now](https://www.adafruit.com/product/4407)
[Related Guides to the Product](https://learn.adafruit.com/products/4407/guides)
Featured
### Lithium Ion Polymer Battery with Short Cable - 3.7V 420mAh
[Lithium Ion Polymer Battery with Short Cable - 3.7V 420mAh](https://www.adafruit.com/product/4236)
Lithium-ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light, and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 420mAh for a total of about 1.55 Wh. If you need a larger (or smaller!) battery,
In Stock
[Buy Now](https://www.adafruit.com/product/4236)
[Related Guides to the Product](https://learn.adafruit.com/products/4236/guides)
Featured
### Breadboard-friendly SPDT Slide Switch
[Breadboard-friendly SPDT Slide Switch](https://www.adafruit.com/product/805)
These nice switches are perfect for use with breadboard and perfboard projects. They have 0.1" spacing and snap in nicely into a solderless breadboard. They're easy to switch no matter what size fingers you have, but not so easy that they'll get flipped by accident. Work great as...
Out of Stock
[Buy Now](https://www.adafruit.com/product/805)
[Related Guides to the Product](https://learn.adafruit.com/products/805/guides)
Featured
### Metal Ball Tactile Button (6mm) x 10 pack
[Metal Ball Tactile Button (6mm) x 10 pack](https://www.adafruit.com/product/3347)
Add some steely elegance to your project with these **Metal Ball Tactile Buttons**. They've got a nice industrial shine to them along with a light blue underbelly. Not only do they look good, but they're also good if you have an actuator that will be pressing the...
In Stock
[Buy Now](https://www.adafruit.com/product/3347)
[Related Guides to the Product](https://learn.adafruit.com/products/3347/guides)
Featured
### Camera and Tripod 3/8" to 1/4" Adapter Screw
[Camera and Tripod 3/8" to 1/4" Adapter Screw](https://www.adafruit.com/product/2392)
_Whaddya got a screw loose or something?_
This **3/8" to 1/4"** **Adapter Screw** is super handy if you're building projects that connect to a tripod or a camera. It's a simple fix for getting a tripod with a 1/4" machine screw...
In Stock
[Buy Now](https://www.adafruit.com/product/2392)
[Related Guides to the Product](https://learn.adafruit.com/products/2392/guides)
# PyBadge Thermal Camera Case
## Circuit Diagram
The diagram below provides a visual reference for wiring of the components. This diagram was created using the software package [Fritzing](http://fritzing.org/download/).
## Adafruit Library for Fritzing
Use Adafruit's Fritzing parts library to create circuit diagrams for your projects. Download the library or just grab individual parts. Get the library and parts from [GitHub - Adafruit Fritzing Parts](https://github.com/adafruit/Fritzing-Library/tree/master/parts).
## Wired Connections
- Switch to **GND**
- Switch to **EN**
- **SDA** from MLX to **SDA** on PyBadge
- **SCL** from MLX to **SCL** on PyBadge
- **VCC** from MLX to **VCC** on PyBadge
- **GND** from MLX to **GND** on PyBadge
- Button to **RESET**
- Button to **GND**
## Powering
The Adafruit board can be powered via USB or JST using a 3.7v lipo battery. In this project, a 420mAh lipo battery is used. The lipo battery is rechargeable via the USB port on the board. The switch is wired to the **enable** and **ground** pins on the board.
# PyBadge Thermal Camera Case
## 3D Printing
## 3D Printed Parts
STL files for 3D printing are oriented to print "as-is" on FDM style machines. Parts are designed to 3D print without any support material. Original design source may be downloaded using the links below.
[Download Fusion 360 Source](https://a360.co/49Z4UEw)
[Download Files from Thingiverse](https://www.thingiverse.com/thing:4306959)
[Download Files from Prusa Printers](https://www.prusaprinters.org/prints/30359-thermal-imaging-camera)
## Screen Bezel
A bezel will help protect the display by keeping it affixed to the PCB. It can be attached to the cover using super glue.
## Attach Bezel to Cover
Apply super glue along the rim of the bezel. Be cautious not to apply too much or too little super glue. Place the cover onto the bezel in the correct orientation.
## Secured Bezel
Allow the glue to fully set before handling or installing. Avoid leaving parts on surfaces to prevent stains from fumes and hazing.
# PyBadge Thermal Camera Case
## Wiring
## Slim Right-Angle Jumpers
Each component features a slim right-angle jumper cable for easily connecting to the headers on the PyBadge. These were created using male jumper cables. The pins are carefully bent at a right-angle and trimmed slightly to fit the short headers. Pins are soldered to the ends of each wire.
## Slide Switch
Connect the slide switch to a piece of 2-wire silicone ribbon cable. 50mm (2in) long wire is recommended. Use the middle pin and either the far left or right pin.
## Stemma Cable
The stemma cable was shortened in this project is not required. There is enough space in the enclosure for the full length of wire.
## Metal Ball Button
Connect the button to a piece of 2-wire silicone ribbon cable. 50mm (2in) is recommended. Use the two pins that are joins on the one side.
# PyBadge Thermal Camera Case
## PyBadge Connections
## Connect Battery
Plug in the JST cable from the battery to the JST port on the PyBadge.
## Connect Reset Button
Plug in the jumper cables from the button to the headers on the pybadge. Connect one wire to a GND pin and the other to RESET.
## Connect Switch
Plug in the cables from the switch to the headers on the PyBadge. Connect one wire to a **GND** pin and the other to the **EN** pin.
# PyBadge Thermal Camera Case
## Install MLX90640
## Hardware
Use the following hardware to mount the breakout board.
- 4x 10mm f/f M2.5 standoff
- 8x M2.5 8mm screws
## Install PCB
Secure the four standoffs to the mounting holes on the breakout PCB. Place the standoffs over the four mounting holes on the 3D printed mount. Use 4x M2.5 x 8mm long screws to secure the board to the mount.
## Secured PCB
Reference the photo for the correct orientation. The PCB should be facing away from the standoffs.
## Connect STEMMA cable
Plug in the STEMMA cable into the input side of the breakout board.
## Install PyBadge
Place the PyBadge PCB onto the mount. Fit the posts on the standoffs into the mounting holes.
## Connect PyBadge
Reference the photo for the correct orientation. Plug in the STEMMA cable from the IR thermal camera breakout to the STEMMA port on the PyBadge.
# PyBadge Thermal Camera Case
## Install Cover
## Installing Cover
The cover is secured to the mount using hardware screws.
## Install Cover
Place the cover on top of the PyBadge and carefully press the buttons through the cover.
## Install Switch
The slide switch is press fitted into a built-in holder on the cover. Insert the switch at an angle and firmly press the body of the switch into the holder on the cover.
## Install Button
The button is press fitted into a built-in holder on the cover. Insert the button at an angle and firmly press the body of the button into the holder on the cover.
## Cover Screws
Use the following hardware screws to secure the cover to the mount.
- 4x M2.5 x 16mm long screws
- 4x M2.5 Nuts
## Secured Cover
Insert the M2.5 screws through the cover and mount. Install and fasten the nuts tightly.
# PyBadge Thermal Camera Case
## Body Assembly
## Cover Body Install
The sides of the enclosure body are fitted onto the rails on the side of the cover.
## Install Body
The enclosure body is symmetrical and fits in either orientation.
## Tripod Screw (Optional)
Insert the 3/8-16 – 1/4-20 tripod adapter into the screw hole on the bottom cover.
## Tripod Screw Installed
The screw is tightened fastened and counter sinks into the hole.
## Bottom Installed
The bottom cover is press fitted onto the bottom side of the enclosure.
## Indents
The enclosure features indentations on the side that allow nubs on the covers to snap fit.
## Installed Top
Press fit the top cover on to the top side of the enclosure.
## Installed Cover
And there you have it! The enclosure is assembled and ready for use.
# PyBadge Thermal Camera Case
## Now add Code!
## Guide Products
### Adafruit PyBadge for MakeCode Arcade, CircuitPython, or Arduino
[Adafruit PyBadge for MakeCode Arcade, CircuitPython, or Arduino](https://www.adafruit.com/product/4200)
What's the size of a credit card and can run CircuitPython, MakeCode Arcade or Arduino? That's right, its the **Adafruit PyBadge!** We wanted to see how much we could cram into a 3 3⁄8 × 2 1⁄8 inch rounded rectangle, to make an all-in-one dev board with...
Out of Stock
[Buy Now](https://www.adafruit.com/product/4200)
[Related Guides to the Product](https://learn.adafruit.com/products/4200/guides)
### Adafruit MLX90640 IR Thermal Camera Breakout
[Adafruit MLX90640 IR Thermal Camera Breakout](https://www.adafruit.com/product/4407)
You can now add affordable heat-vision to your project and with an Adafruit MLX90640 Thermal Camera Breakout. This sensor contains a 24x32 array of IR thermal sensors. When connected to your microcontroller (or Raspberry Pi) it will return an array of 768 individual infrared temperature...
In Stock
[Buy Now](https://www.adafruit.com/product/4407)
[Related Guides to the Product](https://learn.adafruit.com/products/4407/guides)
### Lithium Ion Polymer Battery with Short Cable - 3.7V 420mAh
[Lithium Ion Polymer Battery with Short Cable - 3.7V 420mAh](https://www.adafruit.com/product/4236)
Lithium-ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light, and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 420mAh for a total of about 1.55 Wh. If you need a larger (or smaller!) battery,
In Stock
[Buy Now](https://www.adafruit.com/product/4236)
[Related Guides to the Product](https://learn.adafruit.com/products/4236/guides)
### Breadboard-friendly SPDT Slide Switch
[Breadboard-friendly SPDT Slide Switch](https://www.adafruit.com/product/805)
These nice switches are perfect for use with breadboard and perfboard projects. They have 0.1" spacing and snap in nicely into a solderless breadboard. They're easy to switch no matter what size fingers you have, but not so easy that they'll get flipped by accident. Work great as...
Out of Stock
[Buy Now](https://www.adafruit.com/product/805)
[Related Guides to the Product](https://learn.adafruit.com/products/805/guides)
### Metal Ball Tactile Button (6mm) x 10 pack
[Metal Ball Tactile Button (6mm) x 10 pack](https://www.adafruit.com/product/3347)
Add some steely elegance to your project with these **Metal Ball Tactile Buttons**. They've got a nice industrial shine to them along with a light blue underbelly. Not only do they look good, but they're also good if you have an actuator that will be pressing the...
In Stock
[Buy Now](https://www.adafruit.com/product/3347)
[Related Guides to the Product](https://learn.adafruit.com/products/3347/guides)
### 4-pin JST PH to JST SH Cable - STEMMA to QT / Qwiic
[4-pin JST PH to JST SH Cable - STEMMA to QT / Qwiic](https://www.adafruit.com/product/4424)
Are you a maker in the midst of a [**STEMMA**](https://learn.adafruit.com/introducing-adafruit-stemma-qt/what-is-stemma) dilemma? This 200mm long 4-wire cable is a fantastic chimera-cable fitted with **STEMMA QT / Sparkfun Qwiic JST SH** on one end,...
In Stock
[Buy Now](https://www.adafruit.com/product/4424)
[Related Guides to the Product](https://learn.adafruit.com/products/4424/guides)
### Camera and Tripod 3/8" to 1/4" Adapter Screw
[Camera and Tripod 3/8" to 1/4" Adapter Screw](https://www.adafruit.com/product/2392)
_Whaddya got a screw loose or something?_
This **3/8" to 1/4"** **Adapter Screw** is super handy if you're building projects that connect to a tripod or a camera. It's a simple fix for getting a tripod with a 1/4" machine screw...
In Stock
[Buy Now](https://www.adafruit.com/product/2392)
[Related Guides to the Product](https://learn.adafruit.com/products/2392/guides)
### Silicone Cover Stranded-Core Ribbon Cable - 10 Wire 1 Meter Long
[Silicone Cover Stranded-Core Ribbon Cable - 10 Wire 1 Meter Long](https://www.adafruit.com/product/3890)
For those who are fans of our silicone-covered wires, but are always looking to _up their wiring game_. We now have **Silicone Cover Ribbon cables!** These may look _a lot_ like
Out of Stock
[Buy Now](https://www.adafruit.com/product/3890)
[Related Guides to the Product](https://learn.adafruit.com/products/3890/guides)
## Related Guides
- [Adafruit PyBadge and PyBadge LC](https://learn.adafruit.com/adafruit-pybadge.md)
- [Adafruit MLX90640 IR Thermal Camera](https://learn.adafruit.com/adafruit-mlx90640-ir-thermal-camera.md)
- [BLE Cat Thermal Printer with MEMENTO](https://learn.adafruit.com/ble-cat-thermal-printer-with-memento.md)
- [Discord and Slack Connected Smart Plant with Adafruit IO Actions](https://learn.adafruit.com/discord-and-slack-connected-smart-plant-with-adafruit-io-triggers.md)
- [GoPro Hero 5 NinjaFlex Case with Tripod](https://learn.adafruit.com/gopro-hero-5-ninjaflex-case-with-tripod.md)
- [Motorized Camera Slider MK3 ](https://learn.adafruit.com/motorized-camera-slider-mk3.md)
- [PiCowBell Proto Brick Plates](https://learn.adafruit.com/piccowbell-doubler-brick-plates.md)
- [Light-Up Reactive Ukulele](https://learn.adafruit.com/light-up-reactive-ukulele.md)
- [JOY Controller for Adafruit Feather](https://learn.adafruit.com/joy-controller-feather.md)
- [MagTag Lists From Google Spreadsheets](https://learn.adafruit.com/collaborative-spreadsheets-to-magtag.md)
- [LED Reactive Light-Up Hockey Puck in MakeCode](https://learn.adafruit.com/led-hockey-puck.md)
- [Simple Mini Fume Extractor](https://learn.adafruit.com/simple-mini-fume-extractor.md)
- [USB Host to BLE Keyboard Adapter](https://learn.adafruit.com/esp32-s3-usb-to-ble-keyboard-adapter.md)
- [LED Matrix Hourglass](https://learn.adafruit.com/led-matrix-hourglass.md)
- [Talking Computer from Star Trek](https://learn.adafruit.com/talking-computer-from-star-trek.md)
- [USB MIDI Host Messenger](https://learn.adafruit.com/usb-midi-host-messenger.md)
- [LED Matrix Scoreboard](https://learn.adafruit.com/led-matrix-scoreboard.md)