Featured
Bend all audio files to your will with the Adafruit Music Maker shield for Arduino! This powerful shield features the VS1053, an encoding/decoding (codec) chip that can decode a wide variety of audio formats such as MP3, AAC, Ogg Vorbis, WMA, MIDI, FLAC, WAV (PCM and ADPCM). It can also be...
$29.95 each
In Stock
Featured
This is the Adafruit METRO Arduino-Compatible - with headers. It's a fully assembled and tested microcontroller and physical computing board with through-hole headers attached. If you don't want a Metro with the headers attached for...
view other guides that use this product
$17.50 each
In Stock
Featured
Would you like to add audio/sound effects to your next project, without an Arduino+Shield? Or maybe you don't even know how to use microcontrollers, you just want to make a sound play whenever you press a button. What about something that has to be small...
view other guides that use this product
$19.95 each
In Stock
Featured
Pump up the volume with this 20W stereo amplifier! This slim little board has a class D amplifier onboard that can drive 2 channels of 4-8 ohm impedance speakers at 20W each. Power it with 5-12VDC using the onboard DC power jack and plug stereo line level into the 3.5mm stereo headphone jack...
Out of Stock
Featured
This incredibly small stereo amplifier is surprisingly powerful - able to deliver 2 x 3.7W channels into 3 ohm impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.7V-5.5VDC. Since the amp is a class D, its incredibly efficient (over 90% efficient when...
$8.95 each
In Stock
Featured
Listen up! This high power 4" diameter speaker will amp up any audio project where you need loud sound! It is 4 ohm impedance, rated for 20W continuous power. (This thing is really loud) It also has four handy mounting tabs 3 inches apart, and a grill that fits on top. The grill is to...
$14.95 each
In Stock
Featured
Listen up! This 1.5" diameter speaker cone is the perfect addition to any audio project where you need an 8Ω impedance and are using 0.25W of power. The speakers are rated at 0.25W, with a maximum input of 0.5W (printed wattage on back of speaker may have either value).We...
$1.75 each
In Stock
Featured
PowerBoost 1000C is the perfect power supply for your portable project! With a built-in load-sharing battery charger circuit, you'll be able to keep your power-hungry project running even while recharging the battery! This little DC/DC boost converter module can...
view other guides that use this product
Out of Stock
Featured
Need a big battery for your project? This lithium-ion battery contains a 2200mAh and a protection circuit that provides over-voltage, under-voltage, and over-current protection. Yet, it is slim and easy to fit into many project cases.This cell can provide 2C of...
Out of Stock
Featured
What is better than smart RGB LEDs? Smart RGB+White LEDs! These NeoPixel rings now have 4 LEDs in them (red, green, blue and white) for excellent lighting effects. Round and round and round they go! This is the 16 LED RGBW NeoPixel Ring in Cool White.
$11.95 each
In Stock
Featured
What is better than smart RGB LEDs? Smart RGB+White LEDs! These NeoPixels now have 4 LEDs in them (red, green, blue and white) for excellent lighting effects. Round and round and round they go! This is the NeoPixel 1/4 60 LED Ring in Cool White.
$11.95 each
In Stock
Featured
This Big Freaking Capacitor is just the trick when you have a lot of current sloshing around your project. They'll help smooth out voltage spikes by providing a little buffering. We use these to help stabilize solar panels on our solar Lipoly...
$1.95 each
In Stock
Featured
The "poor man's" accelerometer! Tilt sensors are switches that can detect basic motion/orientation. The metal tube has a little metal ball that rolls around in it, when its tilted upright, the ball rolls onto the contacts sticking out of end and shorts them together.
$2.00 each
In Stock
Featured
Put your project in stealth mode with these silent Soft Tactile Switch Buttons. Tactile switches are standard input "buttons" on electronic projects. These work best in a PCB but
Out of Stock
Featured
This or that, one or the other, perhaps or perhaps not! So hard to make decisions these days without feeling like you're just going back and forth constantly. Deciding whether or not to use this mini toggle switch? That's the easiest decision you'll make all day!This...
$0.95 each
In Stock
Featured
One of the most common converter cables you'll want in your cable collection - this 32" long cable converts a standard 3.5mm stereo jack to pigtail wires. Ground ring is black, middle ring is white and tip is red.
Cable is 32"/81cm long from end to end.
$1.95 each
In Stock
Featured
Perfect for bread-boarding, free wiring, etc. This box contains 6 spools of solid-core wire. These spools of solid-core wires are easily soldered to, keeps its shape pretty well when bent and is rated 80C and 300V (UL AWM style 1007). We...
$15.95 each
In Stock
Featured
These are the finest wire strippers we have used, and if you have to do a lot of wiring, you will agree! They have soft rounded grips - very comfortable to use, and precision ground notches that do a perfect job every time. No more yanking or twisting to strip wires cleanly and quickly.
$17.50 each
In Stock
Featured
This is a 'full-size' premium quality breadboard, 830 tie points. Good for small and medium projects. It's 2.2" x 7" (5.5 cm x 17 cm) with a standard double-strip in the middle and two power rails on both sides. You can pull the power rails off easily to make the...
$5.95 each
In Stock
Featured
Upgrade your RatShack fire-starter iron to this luxurious portable soldering iron. It's durable, with a strong grounded cord, a nice handle and fast heat up. When you don't need a full soldering 'station' this pen type iron will fulfill your needs. At 50W it can handle any task...
No Longer Stocked
Featured
The Ultimaker 2+ is one of our favorite 3D printers on the market. It's a well-built open-source compact machine with an excellent UX. Every inch of the Ultimaker 2+ is designed to create the most effortless and reliable 3D printing experience ever!
No Longer Stocked
Featured
Add mega-storage in a jiffy using this 8 GB class 4 micro-SD card. It comes with a SD adapter so you can use it with any of our shields or adapters. Preformatted to FAT so it works out of the box with our projects. Tested and works great with our
Out of Stock