Is this not the cutest little display for the Raspberry Pi? It features a 2.8" display with 320x240 16-bit color pixels and a resistive touch overlay. The plate uses the high speed SPI interface on the Pi and can use the mini display as a console, X window port, displaying images or video...

Need a massive battery for your project? This lithium-ion pack is made of 3 balanced 2200mAh cells for a total of 6600mA capacity! The cells are connected in parallel and spot-welded to a protection circuit that provides over-voltage, under-voltage, and over-current protection.Each cell...

Need a big battery for your project? This lithium-ion pack is made of 2 balanced 2200mAh cells for a total of 4400mA capacity! The cells are connected in parallel and spot-welded to a protection circuit that provides over-voltage, under-voltage, and over-current protection.Each cell can...

PowerBoost 500C is the perfect power supply for your portable project! With a built-in battery charger circuit, you'll be able to keep your project running even while recharging the battery! This little DC/DC boost converter module can be powered by any 3.7V LiIon/LiPoly battery, and...

These nice switches are perfect for use with breadboard and perfboard projects. They have 0.1" spacing and snap in nicely into a solderless breadboard. They're easy to switch no matter what size fingers you have, but not so easy that they'll get flipped by accident. Work great as...

Listen up! This 1.5" diameter speaker cone is the perfect addition to any audio project where you need an 8Ω impedance and are using 0.25W of power. The speakers are rated at 0.25W, with a maximum input of 0.5W (printed wattage on back of speaker may have either value).We...

This incredibly small stereo amplifier is surprisingly powerful - able to deliver 2 x 2.1W channels into 4 ohm impedance speakers (@ 10% THD). Inside the miniature chip is a class D controller, able to run from 2.7V-5.5VDC. Since the amp is a class D, it's incredibly efficient (89%...

This panel mount extension cable will allow you to extend an HDMI connection and secure it to an enclosure. Perfect for placing your Raspberry Pi in a secure box. Two #4-40 screws are used to attach the female socket end, 26.9mm apart. Two hex-body standoff-screws are included as shown above...

That new Raspberry Pi® Model A or B computer you just got has a row of 2x13 pin headers soldered on - those are the GPIO (general purpose input/output) pins and for those of us who like to hack electronics they are where the real fun is. By programming the Pi, you can twiddle those pins...

These are the finest wire strippers we have used, and if you have to do a lot of wiring, you will agree! They have soft rounded grips - very comfortable to use, and precision ground notches that do a perfect job every time. No more yanking or twisting to strip wires cleanly and quickly.

Make your Pi a little slimmer with this microSD card adapter board. It slides in where the SD card goes but is half the length. Pop in a microSD card for a sleeker machine. The microSD card holder is a push-push type so you can push on the edge that sticks out to remove the card when...

The best mini-vise for working on smaller PCBs (2.875" or less in one dimension)! The jaws are strong plastic that wont damage the PCB and doesn't mind if you hit it with the soldering iron by accident. Made in the USA.The easy-to-use single knob controls head movement...

This 'pen-style' soldering iron is just about the best entry-level tool I've seen. It's not as powerful as a Weller WES51 but it is self-contained and easy to use. With proper care, it will last for many years. Turn it off when not in use, clean the plated tip with a...

New from Printrbot, the Metal Simple is a brand new rock solid, all metal, fully-assembled Printrbot Simple! As opposed to the Printrbot Simple Kit, all of the laser cut wood parts have been replaced by rock solid metal and assembled. In...

Having a 3D printer without filament is sort of like having a regular printer without paper or ink.  And while a lot of printers come with some filament there's a good chance you've been printing up a storm and need something new. That's why we've started carrying a...

Having a 3D printer without filament is sort of like having a regular printer without paper or ink.  And while a lot of printers come with some filament there's a good chance you've been printing up a storm and need something new.  That's why we've started carrying a...

Having a 3D printer without filament is sort of like having a regular printer without paper or ink.  And while a lot of printers come with some filament there's a good chance you've been printing up a storm and need something new.  That's why we've started carrying a...

Discontinued - but check out the Adafruit PiTFT Plus 320x240 2.8" TFT + Capacitive TouchscreenOur best-selling PiTFT 2.8" display just got a fancy...