Top down view of a FLORA - Wearable electronic platform: Arduino-compatible connected to 4 alligator clips and a USB powerin the FLORA.
Featured
FLORA is Adafruit's fully-featured wearable electronics platform. It's a round, sewable, Arduino-compatible microcontroller designed to empower amazing wearables projects.FLORA comes with Adafruit's support, tutorials and...
$14.95 each
In Stock
Adafruit NeoPixel Digital RGB LED Strip reel wired to a microcontroller, with all the LEDs in a rainbow
Featured
You thought it couldn't get better than our world-famous 32-LED-per-meter Digital LED strip but we will prove you wrong! These NeoPixel strips have 30 digitally-addressable pixel LEDs per meter and are very affordable and are only 12.5 mm...
view other guides that use this product
$84.75 each
In Stock
Assembled XBee adapter showing components soldered in.
Featured
This adapter board is designed to make adding wireless point-to-point or mesh networking easy. I looked at all the XBee adapter boards available and decided to design something better:Onboard 3.3V regulator to cleanly power your XBee, up to 250mALevel shifting circuitry...
No Longer Stocked
XBee PRO S2C wireless module with wire antenna.
Featured
We now carry the Series 2 XBee "ZigBee" modules. This is the PRO Series 2 ZigBee protocol 63mW with wire antenna. Its good for point-to-point, multipoint and mesh networks. This module is a little more difficult to get going than the Series 1 - you must set up a...
No Longer Stocked
Angled shot of a Huge 6V 6W Solar panel - 6.0 Watt.
Featured
These panels come to us from Voltaic Systems, makers of fine solar-powered bags and packs. These are waterproof, scratch resistant, and UV resistant. They use a high efficiency monocrystalline cell. They output 6V at 930 mA via 3.5mm x 1.1mm DC jack connector - a nice upgrade to the 2W or 3W...
No Longer Stocked
Angled shot of a Male DC Power adapter - 2.1mm plug
Featured
If you need to connect a battery pack or wired power supply to a board that has a DC jack - this adapter will come in very handy! There is a 2.1mm DC plug on one end, and a screw terminal block on the other. The terminals are labeled with positive/negative assuming a positive-tip configuration...
$2.00 each
In Stock
USB / DC / Solar Lithium Ion/Polymer charger connected to a lithium battery thought a 2-pin JST cable and the solar panel into the DC jack using a 2.1mm adapter cable.
Featured
Make your projects to go green this summer with our specialized USB/Solar Lithium Ion Polymer Battery charger! This charger is a very unique design, perfect for outdoor projects, or DIY iPod chargers. We've spent over a year testing and tinkering with this charger to come up with a plug...
Out of Stock
Black wire with epoxy nub end alongside a resistor next to US quarter for scale.
Featured
Need to measure something damp? This epoxy-coated precision 1% 10K thermistor is an inexpensive way to measure temperature in weather or liquids. The resistance in 25 °C is 10K (+- 1%). The resistance goes down as it gets warmer and goes up as it gets cooler.
$4.00 each
In Stock
Lithium Ion Polymer Battery 3.7v 2500mAh with JST 2-PH connector
Featured
Lithium-ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light, and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 2500mAh for a total of about 10 Wh. If you need a smaller battery,
$14.95 each
In Stock
Small weatherproof enclosure with clear lid.
Featured
Store your project safe and sound in this nice weatherproof box with a clear top. We picked up this box because we like the machinable ABS plastic body and tough clear polycarbonate cover, the built in weatherproof gasket seal, and the easy-open screws that can be taken apart as many times as...
Out of Stock
Top view shot of a red and black JST PH 2-Pin Cable to Female Connector - 100mm.
Featured
Red and black tinned wires with a 2-pin JST PH connector on the end. 4" / 100mm long. Matches up nicely with our Lipoly chargers!We have the socket 'mating' version of this cable over here,
$0.75 each
In Stock
Front shot of JST-PH Battery Extension Cable.
Featured
By popular demand, we now have a handy extension cord for all of our JST PH-terminated battery packs (such as our LiIon/LiPoly and 3xAAA holders). One end has a JST-PH compatible socket, and the other end has a matching plug. Between the two, 500mm of color coded wire. Handy for wearable...
$1.95 each
In Stock
Front cover of "Building Wireless Sensor Networks" by Rob Faludi. Cover features a black-and-white illustration of two collared Dachshunds.
Featured
Get ready to create distributed sensor systems and intelligent interactive devices using the ZigBee wireless networking protocol and Series 2 XBee radios. By the time you're halfway through this fast-paced, hands-on guide, you'll have built a series of useful projects, including a...
No Longer Stocked
Close up head of CdS light sensor showing sensor element
Featured
CdS cells are little light sensors. As the squiggly face is exposed to more light, the resistance goes down. When it's light, the resistance is about ~1KΩ, when dark it goes up to ~10KΩ.To use, connect one side of the photocell (either one, it's symmetric) to power...
$0.95 each
In Stock
10 pieces of Break-away 0.1 inch 36-pin strip male header
Featured
Breakaway header is like the duct tape of electronics. It's great for connecting things together, soldering to perf-boards, fits into any breakout or breadboard, etc. We go through these guys real fast, and thought that given how handy they are, we'd offer them in a pack of ten!
Out of Stock