# LED Eye Prosthetic

## Overview

http://youtu.be/GFlPOY17oK8

These LED augmentations can help you with your cyberpunk costume or other design that requires glowing eyes. this is a super cheap, simple circuit comprised of a battery and LEDs. You will need patience and a steady hand, however.

Make sure your soldering iron has a fine tip and use SMD LEDs in size 1206. This size has about a 1mm distance between the terminal foot and the top of the acryllic cap, allowing a 1mm enamel wire to sit in that gap very comfortably.

![](https://cdn-learn.adafruit.com/assets/assets/000/020/549/medium800/components_tully-jagoe-led-glasses.jpg?1413924190)

# LED Eye Prosthetic

## Parts List

 **For this project you will need:**

- 20x SMD LEDs, size 1206. Pick any colour you want, you could even mix and match (as long as they have the same forward voltage)!
- 1mm enamelled single core copper wire - this is also called 'Magnet wire' and can be a little tough to get in less than 100' spools
- [CR2032 battery](https://www.adafruit.com/products/654)
- [CR2032 battery breakout with switch](https://www.adafruit.com/products/1871)
- [Fine tip curved tweezers](https://www.adafruit.com/products/422)
- [Flush diagonal cutters](https://www.adafruit.com/products/152)
- [Soldering iron](https://www.adafruit.com/products/1204) with [fine tip](https://www.adafruit.com/products/1249)
- Permanent marker
- craft knife or sandpaper
- Soft jaw clamp

# LED Eye Prosthetic

## Prepare wires

![](https://cdn-learn.adafruit.com/assets/assets/000/019/890/medium800/components_2014-09-26_10_36_50-LED_Eye_Prosthetic_Tutorial_on_Vimeo.png?1411699048)

Start by cutting two lengths of enamelled wire to encompass your head, leaving about 4 to 5cm extra on each side. 

![](https://cdn-learn.adafruit.com/assets/assets/000/019/891/medium800/components_2014-09-26_10_38_34-LED_Eye_Prosthetic_Tutorial_on_Vimeo.png?1411699255)

Mark one of these wires with a sharpie along its length, to denote a negative wire. 

![](https://cdn-learn.adafruit.com/assets/assets/000/019/892/medium800/components_2014-09-26_10_40_44-LED_Eye_Prosthetic_Tutorial_on_Vimeo.png?1411699470)

Twist these two wires together along their length, remembering to leave about 4cm each end untwisted for the LED mounting points. Cut wires equally into two lengths.

![](https://cdn-learn.adafruit.com/assets/assets/000/019/894/medium800/components_2014-09-26_10_45_16-LED_Eye_Prosthetic_Tutorial_on_Vimeo.png?1411700188)

Using sandpaper or a craft knife, strip all the enamel off the 4 straight ends of the two lengths. Tin the wires with solder, making sure to only coat them and not leave lumps on the terminals. 

Info: 

Using the soft jaw clamp, affix one of the wire lengths to the table, and arrange the straight ends to leave a 2mm gap.

# LED Eye Prosthetic

## Solder LEDs

![](https://cdn-learn.adafruit.com/assets/assets/000/019/895/medium800/components_2014-09-26_10_57_21-LED_Eye_Prosthetic_Tutorial_on_Vimeo.png?1411700312)

Drop an LED face down into this gap using curved tweezers, arranging them so the green line points towards the black negative wire marked earlier.

![](https://cdn-learn.adafruit.com/assets/assets/000/019/898/medium800/components_2014-09-26_10_57_54-LED_Eye_Prosthetic_Tutorial_on_Vimeo.png?1411700367)

Info: 

![](https://cdn-learn.adafruit.com/assets/assets/000/019/899/medium800/components_2014-09-26_10_59_41-LED_Eye_Prosthetic_Tutorial_on_Vimeo.png?1411700717)

Continue to add LEDs into the gap and solder them in place directly next to each other, until you have the desired length of LED line. Allow it to completely cool.

Be patient, take your time, clean up messy solder as you go. To clean up lumps, run the soldering iron along the outside edge of the wire quickly, so as to not heat it up enough to remelt the existing links, but just enough to smooth out surface irregularities. This may take a few tries but you'll get the knack of it.

![](https://cdn-learn.adafruit.com/assets/assets/000/019/900/medium800/components_2014-09-26_11_00_01-LED_Eye_Prosthetic_Tutorial_on_Vimeo.png?1411700751)

Repeat this step with the other section of wire. Clip off any remaining wire flush with the last LED in the line.

![](https://cdn-learn.adafruit.com/assets/assets/000/019/908/medium800/components_1016164_10151538179913381_412272675_n.jpg?1411703152)

Once you're all done, touch the remaining loose ends to either side of your CR2032 battery to test the connection. If any LEDs do not illuminate, make sure they're placed in the right way round, and strengthen any solder connections that look bad. Once it's all good, it should look like the photo above.

# LED Eye Prosthetic

## Attach battery holder

![](https://cdn-learn.adafruit.com/assets/assets/000/019/901/medium800/components_2014-09-26_11_15_01-LED_Eye_Prosthetic_Tutorial_on_Vimeo.png?1411701348)

The good news is that the hard part is over, and if you weren't a soldering pro before, you are now. Get your Adafruit switched CR2032 battery clip, Solder the four header pins in place. Clip off the two middle ones, they'll only get in the way.

![](https://cdn-learn.adafruit.com/assets/assets/000/019/902/medium800/components_2014-09-26_11_19_34-LED_Eye_Prosthetic_Tutorial_on_Vimeo.png?1411701600)

Thread the free ends of the two wire twists through the large holes for a bit of strain relief and arrangement. Strip off a small amount of enamel on the remaining 4 ends, solder the negative wires to GND and the positive wires to SW.

### 

With the wires outside of the holes, any movement in the wire is concentrated on the solder points, which is structurally weak. When threaded through the holes first, the movement is concentrated at the holes where the wire is much stronger, and any pulling on the wires will direct the force in direct opposition to the strength of the other wire, adding further strain relief.

# LED Eye Prosthetic

## Shape it to your skull

![](https://cdn-learn.adafruit.com/assets/assets/000/019/903/medium800/components_2014-09-26_09_49_20-LED_Eye_Prosthetic_Tutorial_on_Vimeo.png?1411701855)

With the battery clip on the back of your neck, start shaping the wires around and over your ears. It should eventually look something like this.

It's kind of like wearing sunglasses backwards, the ear loops should rest over the top and down the front of your ears to hold itself steady. form the led's in front of your eyes, facing out.

Info: 

# LED Eye Prosthetic

## Wear it!

![](https://cdn-learn.adafruit.com/assets/assets/000/019/904/medium800/components_1510660_10152035696178381_1952669276_n.jpg?1411702935)

You're done! Power it up and run around in the dark! The LEDs only throw light forward, so it should interfere with your vision very little. If desired, glue small strips of black plastic to reduce light bleed. This aug is very bright and you should easily be able to see your way around even in a pitch black room. Wear behind sunglasses for an 80's cyberpunk look :D

![](https://cdn-learn.adafruit.com/assets/assets/000/019/905/medium800/components_1011043_10151545231088381_65360295_n.jpg?1411702948)

![](https://cdn-learn.adafruit.com/assets/assets/000/019/906/medium800/components_998592_10151543017443381_1698012938_n.jpg?1411702982)

![](https://cdn-learn.adafruit.com/assets/assets/000/019/907/medium800/components_1012625_10151538313723381_1780223890_n.jpg?1411702998)

![](https://cdn-learn.adafruit.com/assets/assets/000/020/607/medium800/components_Screen_Shot_2014-10-24_at_12.40.52_PM.png?1414168938)

![](https://cdn-learn.adafruit.com/assets/assets/000/020/608/medium800/components_Screen_Shot_2014-10-24_at_12.41.48_PM.png?1414168953)


## Featured Products

### 20mm Coin Cell Breakout w/On-Off Switch (CR2032)

[20mm Coin Cell Breakout w/On-Off Switch (CR2032)](https://www.adafruit.com/product/1871)
Simple but effective - this sewable breakout board has a CR2032 coin cell battery holder soldered on, an on/off switch and 0.1" pitch breakout pins for easy connecting. Great for powering very low-current projects, or adding a battery backup circuit to a real-time-clock or similar....

In Stock
[Buy Now](https://www.adafruit.com/product/1871)
[Related Guides to the Product](https://learn.adafruit.com/products/1871/guides)
### CR2032 Lithium Coin Cell Battery

[CR2032 Lithium Coin Cell Battery](https://www.adafruit.com/product/654)
A perfect match for our [sew-able coin cell holder](http://www.adafruit.com/products/653). This non-rechargeable coin cell is CR2032 sized: 20mm diameter, 3.2mm thick. It has a nominal voltage output of 3V (although it starts a little high at 3.2V and slowly drifts down to 2.5V as...

In Stock
[Buy Now](https://www.adafruit.com/product/654)
[Related Guides to the Product](https://learn.adafruit.com/products/654/guides)
### Fine tip curved tweezers - ESD safe

[Fine tip curved tweezers - ESD safe](https://www.adafruit.com/product/422)
When soldering small surface-mount (SMD/SMT) components, one thing you'll need is a good pair of tweezers. These are a great pair of every-day tweezers. They're anti-static, anti-magnetic and made of hard stainless steel. The tips are fine and pointy to pick up any size component. This...

In Stock
[Buy Now](https://www.adafruit.com/product/422)
[Related Guides to the Product](https://learn.adafruit.com/products/422/guides)
### Flush diagonal cutters

[Flush diagonal cutters](https://www.adafruit.com/product/152)
These are the best diagonal cutters, large super-comfortable grip to use and have strong nippers for perfect trimming of wires and leads. I've used my pair every day for years.

In Stock
[Buy Now](https://www.adafruit.com/product/152)
[Related Guides to the Product](https://learn.adafruit.com/products/152/guides)
### Hakko Soldering Tip: T18-S4 Fine SMD - For Lead or Lead-Free Use

[Hakko Soldering Tip: T18-S4 Fine SMD - For Lead or Lead-Free Use](https://www.adafruit.com/product/1249)
Upgrade your Hakko with a new tip, you'll get better & faster solder joints and the whole process will be much more enjoyable. This tip fits the FX-888 analog and digital irons, and they're fast to swap, takes only 30 seconds to change out. All the tips are good for either lead or...

In Stock
[Buy Now](https://www.adafruit.com/product/1249)
[Related Guides to the Product](https://learn.adafruit.com/products/1249/guides)
### Digital Genuine Hakko FX888DX-010SV (936 upgrade)

[Digital Genuine Hakko FX888DX-010SV (936 upgrade)](https://www.adafruit.com/product/1204)
Known by engineers for making excellent quality tools & soldering irons! This is a genuine Hakko FX-888D with **digital temperature control**! We worked hard to get the best and a great price, these are **not**  knock-offs. This iron is an upgrade to the...

No Longer Stocked
[Buy Now](https://www.adafruit.com/product/1204)
[Related Guides to the Product](https://learn.adafruit.com/products/1204/guides)

## Related Guides

- [Machine Learning with Marshmallows and Tiny Sorter](https://learn.adafruit.com/machine-learning-with-marshmallows-and-tiny-sorter.md)
- [Glowing Birthday Number Crown](https://learn.adafruit.com/glowing-birthday-number-crown.md)
- [LEGO Set Lighting](https://learn.adafruit.com/lego-set-lighting.md)
- [Light Up your Costume with Noods](https://learn.adafruit.com/light-up-your-costume-with-noods.md)
- [Bo-Katan LED Headband](https://learn.adafruit.com/led-headband.md)
- [LED Masquerade Masks with n00ds](https://learn.adafruit.com/led-masquerade-masks-with-n00ds.md)
- [Moana Glowing Heart of Te Fiti Necklace](https://learn.adafruit.com/moana-glowing-heart-of-te-fiti-necklace.md)
- [Glowing Hair Flowers with n00ds](https://learn.adafruit.com/glowing-hair-flowers-with-n00ds.md)
- [Battery Powering Wearable Electronics](https://learn.adafruit.com/battery-powering-wearable-electronics.md)
- [LED Sequin Bow Tie](https://learn.adafruit.com/led-sequin-bowtie.md)
- [EEG Costume Cap](https://learn.adafruit.com/eeg-costume-cap.md)
- [All About Stepper Motors](https://learn.adafruit.com/all-about-stepper-motors.md)
- [Adafruit bq25185 USB / DC / Solar Charger with 3.3V Buck Board](https://learn.adafruit.com/adafruit-bq25185-usb-dc-solar-charger-with-3-3v-buck-board.md)
- [Connecting the MAX31855 Thermocouple Amplifier breakout to an Electric Imp](https://learn.adafruit.com/connecting-the-max31855-thermocouple-amplifier-breakout-to-an-electric-imp.md)
- [Wires and Connections](https://learn.adafruit.com/wires-and-connections.md)