Pink polished fingers holding a Adafruit GEMMA M0 - Miniature wearable electronic platform.
The Adafruit Gemma M0 is a super small microcontroller board, with just enough built-in to create many simple projects. It may look small and cute: round, about the...
Out of Stock
Purple poslished fingers holding a Adafruit GEMMA v2 - Miniature wearable electronic platform.
Deprecation Warning: The Gemma bit-bang USB technique it uses doesn't work as well as it did in 2014, many modern computers won't work well. So while we still carry the...
$9.95
In Stock
A collection of electronic parts included in the starters pack.
Make your wearables glow with the GEMMA sequin pack! This GEMMA parts pack makes it easy to add light to your wearables. It comes with thread, needles, a holder for 2...
$17.95
In Stock
Angled shot of Conductive Hook & Loop Tape side by side.
Conductive hook & loop tape is just like the stuff you've seen on jackets, clothes, shoes, and bags, but is coated with silver to make it fully conductive. Originally this was...
$6.95
In Stock
Single LED sequin PCB attached to two alligator clips, glowing white
Sew a little sparkle into your wearable project with an Adafruit LED Sequin. These are the kid-sister to our popular Flora NeoPixel,...
$3.95
In Stock
Angled shot of closed 2 x 2032 coin cell battery holder with on-off switch and JST PH Connector.
This tiny coin cell battery holder is ideal for small portable or wearable projects. It holds two 20mm coin cells (2032 or CR2032 are the most popular size) in series to generate 6V...
$1.95
In Stock
Stainless Thin Conductive Thread - 2 ply - 23 meter/76 ft
After months of searching, we finally have what we consider to be the ultimate conductive thread. It's thin, strong, smooth, and made completely of 316L stainless steel. Once you...
$6.95
In Stock
Needle set - 3/9 sizes - 20 needles
Mighty needles, sew like the wind! This needle set is the only one you'll need for any sort of hand sewing, especially using our conductive thread and wearable electronics...
$1.95
In Stock
Front shot of CR2032 Lithium Coin Cell Battery upright.
A perfect match for our sew-able coin cell holder. This non-rechargeable coin cell is CR2032 sized: 20mm diameter, 3.2mm thick. It...
$0.95
In Stock
Single LED sequin PCB attached to two alligator clips, glowing red
Sew a little sparkle into your wearable project with an Adafruit LED Sequin. These are the kid-sister to our popular Flora NeoPixel,...
$3.95
In Stock
Single LED sequin PCB attached to two alligator clips, glowing green
Sew a little sparkle into your wearable project with an Adafruit LED Sequin. These are the kid-sister to our popular Flora NeoPixel,...
$3.95
In Stock
Single LED sequin PCB attached to two alligator clips, glowing blue
Sew a little sparkle into your wearable project with an Adafruit LED Sequin. These are the kid-sister to our popular Flora NeoPixel,...
$3.95
In Stock
Close up of pink rose lit LED powered by two alligator clips
Sew a little sparkle into your wearable project with an Adafruit LED Sequin. These are the kid-sister to our popular Flora NeoPixel,...
$3.95
In Stock
Kit contents shot with Gemma, needles, Flora pixels, alligator clips, etc.
Get started with Adafruit GEMMA with this lovely starter kit! Included is everything you need to make a basic project. There's a GEMMA board, four sewable bright RGB pixels, a...
$27.95
In Stock
A collection of electronic parts included in a starters pack.
Go interactive with sensors and Adafruit GEMMA with this lovely starter kit! Included is everything you need to make a basic sensing project (or two). There's a GEMMA board, four...
Out of Stock