Quick Connect Cables
Use two sets of quick connect cables for wiring the arcade button switch and LED.
Cut off the JST connectors from wires, leaving only the spade connectors.
Use wire strippers to remove a bit of insulation from each wire.
Tin the exposed wire using a bit of solder.
Secure Feather
Place the Feather onto the PCB mount in the correct orientation as shown here.
Insert and fasten the M2.5 screws to secure the Feather to the PCB mount.
Mounts for Speaker
Use 4x M3 x 10mm long screws and hex nut to secure the 3W enclosed speaker to the two speaker mounts.
Secure Speaker
Place one of the two mounts behind the mounting tabs on the enclosed speaker.
Insert an M3 screw through the mounting tab and fasten a hex nut to secure the mount to the enclosed speaker.
Repeat process for the second speaker mount.
Join Bottom and Middle Boxes
Use 4x M3 x 10mm long screws and hex nuts to secure the bottom box to the middle box.
Secure Bottom and Middle Boxes
Orient the bottom and middle box so the center and mounting holes are lined up correctly.
Insert and fasten the M3 screws through the mounting holes. Install the M3 hex nuts to secure the two boxes together.
Install Panel A
Insert Panel A through the slotted opening in the middle box. Push to slide the panel all the through.
Ensure the panel is facing the desired surface.
Arcade Button Parts
Disassemble the parts from the arcade button. To remove the switch from the threaded stem of the button, twist counter-clockwise and pull out.
Unscrew the included nut from the threaded stem and remove the coupling plate.
Attach Bezel
Use adhesive or double-sided tape to secure the 3D printed bezel to the black outer ring of the arcade button.
Be careful not to add too much adhesive to avoid squeeze out.
Press the button actuator to ensure it still works properly.
Install Arcade Button
Insert the button from the front with the notches lined up properly. Push button until it's flush with the panel.
Secure Arcade Button
Flip assembly to the back and replace the coupling plate. Twist the coupling plate until it latches onto the notch.
Insert and fasten the included plastic nut onto the threaded stem. Twist until fully tightened.
Panel Mounted Arcade Button
Take a moment to ensure the arcade button is properly secured to the panel.
Install Speaker to Bottom Box
Get the speaker ready to secure to the bottom box.
Insert the speaker from the back and line up the mounting tabs with the mounting holes on the side.
Secure Speaker to Bottom Box
Insert 4x M3 x 10mm screws through the side of the bottom box and tabs of the speaker mount.
Fasten 4x M3 hex nuts onto the screws to secure the speaker.
Adhere Label to Panel B
Get the 3D printed label ready to attach to Panel B.
Use adhesive or double-sided tape to adhere the label to the panel.
Reference the photo for best placement. Ensure the orientation of the label is correct.
Install Label to Top Box
Insert the panel into the slotted opening in the top box.
Push to slide the panel all the way through.
Secure Top Box to Middle Box
Bring the top box to the middle box and ensure the center and mounting holes are lined up.
Use 4x M3 x 10mm long screws and hex nuts to secure the top box to the middle box.
Install LED to Arcade Button
Begin installing the LED back onto the arcade button.
Insert and twist clockwise to lock the switch into the threaded stem.
Install Wires for LED
Firmly press the blue wire spade connector onto the cathode terminal of the LED.
Repeat for the white wire and anode terminal of the LED.
Install Wires for Switch
Firmly insert a white wire spade connector onto the normally open (NO) terminal of the switch.
Repeat for the blue wire onto the common terminal.
Install Speaker Wires to Feather
Insert and secure the two wires from the speaker to the speaker screw-block terminals on the Feather.
Install Ground Wires to Feather
Insert and secure the two blue wires into the ground screw-block terminal on the Feather.
Install LED+ Wire
Insert and secure the white wire from the LED to the NEO pin screw-block terminal on the Feather.
Install Switch Wire to Feather
Insert and secure the white wire from the switch to the BUTTON pin screw-block terminal on the Feather.
Secure Feather Mount
Position the PCB Mount into the bottom box with the mounting tabs lined up with the mounting holes.
Use 2x M3 x 10mm long screws and hex nuts to secure the PCB mount to the bottom box.
Install Grill
Orient the speaker grill face up and press fit into the recess of the bottom box until it's flush.
USB Power
Insert a USB-C type cable to the Feather's USB port. Use a 5V 2A wall adapter or computer USB hub to power the Feather.
Text editor powered by tinymce.
