Antenna Options
This guide documents two ways to make a suitable antenna for HF SSTV: a long wire antenna with a balun one nine, and an MLA-30 active loop antenna. I have successfully captured SSTV images with both types. Either will work fine, but there are some tradeoffs to consider.
Both require some assembly and cost is similar between them. The active loop requires a USB power source, needs much less space, and has a little more assembly work. The long wire antenna is very simple to build, it requires only stripping a small length of the wire insulation and tinning the end with solder. It needs more time and effort to set up and take down. It needs a lot of space to set up, and can get tangled if not handled carefully.
Nooelec Balun One Nine v2
This balun device lets you hook up the long wire antenna. The balun sits between the long wires and the SDR.
I used the version with aluminum enclosure, but there is a bare bones one available as well for a few bucks less. They are available from Nooelec directly, or Amazon and other online retailers.
Coax Cable (Optional)
The Balun One Nine with enclosure kit comes with a small male SMA to male SMA adapter. This could be used to connect it to the SDR. A 6-12 ft / 1.82-3.65 m cable, like this one, can extend the connection further and make the setup a little more flexible.
If you do opt for the cable, using ferrite choke clips on it can reduce interference from it.
Long Wire
You'll need two lengths of wire:
- 58 ft / 17.68 m length for the antenna
- 15-25 ft 4.57-7.62 m length for the GND wire
I got a 100ft / 30 m roll of 18/2 speaker wire from a hardware store. Any 18 or 20 gauge stranded wire should work.
This speaker wire comes with two wires connected together by their insulation. I cut a 60 ft / 18.28 m length of it off the retail spool, then pulled it apart at the insulation seam so that I ended up with two 60 ft / 18.28 m wires. Next I cut 2 ft / 0.6 m off of one of them and cut the other into a split of 41 ft / 12.49 m and 19 ft / 5.79 m.
A 41 ft / 12.49 m length of antenna will work instead of 58 ft / 17.67 m for frequency 14.230. I tested both, but recommend using the 58 ft / 17.67 m length for anyone following along, it's better at receiving 7.171 on 40m band, and I got overall cleaner images from the 58 ft / 17.67 m wire. Though I did also let the listener run longer on the 58 ft / 17.67 m, and conditions will vary with time and location.
If you have dual speaker wire like I did you can follow the same approach I used to test both 41 ft / 12.49 m and 58 ft / 17.67 m feet if you're interested in the difference.
Additional Tools
- Wire cutters and stripper
- Soldering iron
- Small flat head screw driver for the wire terminal connectors
MLA-30 Loop Antenna Kit
These kits are available from various online retailers. The antenna kit needs to be assembled, it's intended to mount to a piece of PVC tube or a wooden dowel. I opted for the PVC tube.
3/4" / 1.90 cm PVC Pipe & Cap
At least 3 ft / 1 m in length. I used a 5 ft / 1.52 m section that the hardware store had cheap pre-cut lengths of.
Get a 3/4" / 1.90 cm PVC cap as well to fit over the top end of the antenna. It will help keep water and debris out of the PVC pipe while it's outdoors.
Antenna Mount
You need some way to mount or hold the antenna. The antenna being made of 3/4" PVC makes for many possible options. Umbrella holders, backyard torch holders, and flag mounts to name a few. You could even fashion your own holder in a number of creative ways.
I used a 2 gallon bucket with a few inches of sand in it. The lid has a cross of slits cut into the center of it. The PVC antenna pole shoves down into the center and it's bottom is held steady by the sand. The sand also gives it enough weight to resist blowing around in casual winds.
Page last edited October 19, 2026