# FPV Mini Display ## Overview https://www.youtube.com/watch?v=dOwJ6KlTIeQ ![](https://cdn-learn.adafruit.com/assets/assets/000/032/824/medium800/lcds___displays_hero-in-use.jpg?1464700026) ## Mini FPV monitor Build a tiny portable FPV (First-person view) monitor! Great to use as a spectator display at an event or attach to your controller as a backup to goggles. It's rechargeable and has access to the band, channel and brightness controls. ![](https://cdn-learn.adafruit.com/assets/assets/000/032/825/medium800/lcds___displays_hero-complete.jpg?1464748485) The 2.5" TFT display is powered by a 500mAh lipo battery and a PowerBoost 1000C. The Eachine ER32 VRX AV receiver has 32 channels with frequencies from 5645-5945MHz. Small and low cost with a wide voltage input, it connects to the PowerBoost 1000C. ![](https://cdn-learn.adafruit.com/assets/assets/000/032/832/medium800/lcds___displays_circuit-parts.jpg?1464800840) ## Adafruit Parts - [2.5" TFT Display](https://www.adafruit.com/products/912) - [Powerboost 1000c](https://www.adafruit.com/products/2465) - [6mm Slim Buttons](https://www.adafruit.com/products/1489) - [500mAh Battery](https://www.adafruit.com/products/1578) - [Slide Switch](https://www.adafruit.com/products/805) - [Eachine ER32 VRX FPV AV Receiver](http://amzn.com/B017BFX3JQ) ## Tools and Supplies - [3D Printer](https://www.adafruit.com/category/128) + [Filament](https://www.adafruit.com/products/2080) - [Soldering Iron](https://www.adafruit.com/categories/84) + [Solder](https://www.adafruit.com/categories/84) - [30AWG Wire](https://www.adafruit.com/products/2051) - [Helping Third Hands](https://www.adafruit.com/products/291) / [Panavise](https://www.adafruit.com/products/151) - [Heat Shrink](https://www.adafruit.com/products/1649) - Mounting Tack - [Wire Stripper](https://www.adafruit.com/products/527) / [Cutters](https://www.adafruit.com/products/152) - Hobby Knife ![](https://cdn-learn.adafruit.com/assets/assets/000/032/823/medium800thumb/lcds___displays_hero-controller-loop.jpg?1464621604) # FPV Mini Display ## Circuit Diagram ![](https://cdn-learn.adafruit.com/assets/assets/000/032/831/medium800/lcds___displays_wire-measure.jpg?1464798842) ## Electronics Follow the circuit diagram below and reference the connections for wiring the circuit. Lay out the parts and circuits as shown and then measure each wire with enough slack to solder each component. Lable each set of wires to keep track which wire goes where. ![](https://cdn-learn.adafruit.com/assets/assets/000/032/830/medium800/lcds___displays_circuit-diagram.jpg?1464797382) ## Display Driver Remove the driver from the display to make soldering easy. Use a panavise to hold the board in place while soldering. Solder the  **Video +** (4th pin) to the 3rd pin on the FPV receiver. Solder  **Video -**  (3rd pin) to the 2nd pin on the FPV receiver. Connect the 1st pin on the display to the **5v** on the powerboost. The 2nd pin on the driver connects to the **G** pin on the powerboost. The order of the pins for the **Brightness** button don't matter. ## FPV receiver The 1st pin on the FPV connects to  **+** on the powerboost. The 2nd pin on the FPV connects to the **-** on the powerboost. The order of the pin for the **Band** and **Channel** button don't matter. ## Slide Switch Trim the pins short on the slide switch before soldering wires.  Connect one of the pins on the slide switch to the **EN** pin on powerboost. Connect  **GND** right next to the EN pin on the slide switch. # FPV Mini Display ## 3D Printing ![](https://cdn-learn.adafruit.com/assets/assets/000/032/817/medium800/lcds___displays_3d-parts.jpg?1464619729) [Download Design](http://www.thingiverse.com/thing:1611044) [Edit Design](http://a360.co/1RVqtpu) ## 3D Printed Parts The FPV Monitor is split into 5 different pieces. The two case parts snap fit together without any screws.  The 6mm buttons mount into the lid part.   A riser fits on top of the Powerboost 1000c to elevate the FPV Receiver. Use #6-32 1/2in screws with nuts to attach the two clamps on controllers. An M5 x 20 Bolt and acorn nut attaches the case to the clamp parts. ## Slicer Settings To slice the parts, we used Simplify3D. We recommend using the settings below or use them as reference. We 3D printed these parts on a Ultimaker 2+. If you have Simplify3D, you can download our profiles below. ## Customize The Design The parts where designed in Autodesk Fusion 360. The design is public and available to download in different formats. If you'd like to use a different CAD software package, you are free to import the files and remix them. [Customize Design](https://www.youtube.com/watch?v=Qv-nTkJnz1w) ## Filament Materials We recommend using PLA material to reduce wrapping while 3D printing. The parts can be printed in different types of filament, such as ABS, PET or Nylon. ## Tolerances The slots for the buttons may have tight tolerances. Test the tolerances by inserting all of components into each slot. If parts don't fit into the slots, you may need to use a craft knife or filing tool to loosen the area. ![](https://cdn-learn.adafruit.com/assets/assets/000/032/826/medium800/lcds___displays_case_supports.png?1464752090) ## Generating Supports The top body case will need supports underneath the three hinge parts. We can optimize the print by adding supports beneath three hinge parts until it looks like the picture above.  ![](https://cdn-learn.adafruit.com/assets/assets/000/032/827/medium800/lcds___displays_lid_supports.png?1464752129) For the lid, add one support pillars inside each button slot. Make sure the pillars don't touch the side of the walls or the supports can fuse to the walls of the slots. ![](https://cdn-learn.adafruit.com/assets/assets/000/032/779/medium800/lcds___displays_case-supports.jpg?1464556412) ## Removing supports Use flat pliers to help remove supports. The supports should pull off easy, but take care not to damage the hinge if the supports are fused to the parts. ![](https://cdn-learn.adafruit.com/assets/assets/000/032/781/medium800/lcds___displays_lid-supports.jpg?1464557759) Use flat pliers to remove the supports inside the button slots. ![](https://cdn-learn.adafruit.com/assets/assets/000/032/782/medium800/lcds___displays_clean-ports.jpg?1464557798) Use a hobby knife to remove left over filament left over from retraction. # FPV Mini Display ## Assemble https://www.youtube.com/watch?v=Qv-nTkJnz1w ## Display driver To make soldering easy, we'll need to remove the display driver by unlocking the black plastic bar to release the ribbon cable. Use a panavise to hold the driver while soldering each wire as shown in the circuit diagram. ![lcds___displays_display-driver-remove.jpg](https://cdn-learn.adafruit.com/assets/assets/000/032/814/medium640/lcds___displays_display-driver-remove.jpg?1464618971) ![lcds___displays_display-solder.jpg](https://cdn-learn.adafruit.com/assets/assets/000/032/815/medium640/lcds___displays_display-solder.jpg?1464619003) ![](https://cdn-learn.adafruit.com/assets/assets/000/032/797/medium800/lcds___displays_brightness-button-solder.jpg?1464575376) ## Brightness button Solder wires to the two pads as shown above. Careful not to bridge any connections by using a fine tip to solder. ![](https://cdn-learn.adafruit.com/assets/assets/000/032/803/medium800/lcds___displays_tv-soldered.jpg?1464576416) ## FPV AV Receiver Carefully tin and solder each wire for composite, composite negative, power, ground, band and channel buttons. ## Adding Tac We couldn't fit standoffs in the compact enclosure, so mounting tac is used to hold the battery and powerboost in place. Add four dots to the battery and five dots to the powerboost to help them stick to the back of the display. Make sure to add enough tac so they are elevated above the display.  ![lcds___displays_battery-add-tac.jpg](https://cdn-learn.adafruit.com/assets/assets/000/032/789/medium640/lcds___displays_battery-add-tac.jpg?1464558011) ![lcds___displays_powerboost-tac.jpg](https://cdn-learn.adafruit.com/assets/assets/000/032/790/medium640/lcds___displays_powerboost-tac.jpg?1464558025) ## Mounting buttons Straighten the pins on the buttons so the can fit through the slots inside the mounts. Use a flat plier bend to the pins. The tolerances will be tight, use a hobby knife to help loosen the slots. ![lcds___displays_button-pin-bend.jpg](https://cdn-learn.adafruit.com/assets/assets/000/032/799/medium640/lcds___displays_button-pin-bend.jpg?1464575447) ![lcds___displays_button-insert.jpg](https://cdn-learn.adafruit.com/assets/assets/000/032/800/medium640/lcds___displays_button-insert.jpg?1464575694) ## Tin buttons Make sure the button pins poke through the slots and tin and solder each button. Use a panavise to hold the lid while soldering. ![lcds___displays_button-mounted.jpg](https://cdn-learn.adafruit.com/assets/assets/000/032/801/medium640/lcds___displays_button-mounted.jpg?1464575987) ![lcds___displays_buttons-tin.jpg](https://cdn-learn.adafruit.com/assets/assets/000/032/802/medium640/lcds___displays_buttons-tin.jpg?1464576030) ## Solder Powerboost Solder each connection to the powerboost as shown in the circuit diagram.   ## Slide Switch Shorten the pins on the slide switch with a flush cutters and then tin and solder each wire. ![lcds___displays_switch-trim-pins.jpg](https://cdn-learn.adafruit.com/assets/assets/000/032/804/medium640/lcds___displays_switch-trim-pins.jpg?1464576471) ![lcds___displays_solder-switch.jpg](https://cdn-learn.adafruit.com/assets/assets/000/032/805/medium640/lcds___displays_solder-switch.jpg?1464576499) ![](https://cdn-learn.adafruit.com/assets/assets/000/032/806/medium800/lcds___displays_complete-circuit.jpg?1464576626) ## Circuit Complete!   ![](https://cdn-learn.adafruit.com/assets/assets/000/032/807/medium800/lcds___displays_battery-tac.jpg?1464576651) Add tac to the top of the battery to help level the display driver. ![](https://cdn-learn.adafruit.com/assets/assets/000/032/810/medium800thumb/lcds___displays_insert-complete.jpg?1464579127) ## Insert into case Make sure the clean the inside of the case of any filament left over from retraction before fitting the components inside. Carefully angle the display into the case as shown.  ![](https://cdn-learn.adafruit.com/assets/assets/000/032/808/medium800/lcds___displays_tv-tac.jpg?1464576694) Add tac to the powerboost riser to mount the FPV receiver.  ![](https://cdn-learn.adafruit.com/assets/assets/000/032/813/medium800/lcds___displays_hero-complete.jpg?1464618897) ## Antenna Screw on the antenna to the receiver and tune to the channel the FPV camera is on the test the monitor. ## Attaching display to controller If you plan to use the monitor on the controller,  use #6-32 1/2 inch screws and nuts to attach the clamp parts to the antenna on the controller. ![lcds___displays_clamp-complete.jpg](https://cdn-learn.adafruit.com/assets/assets/000/032/818/medium640/lcds___displays_clamp-complete.jpg?1464619821) ![lcds___displays_clamps-mount.jpg](https://cdn-learn.adafruit.com/assets/assets/000/032/820/medium640/lcds___displays_clamps-mount.jpg?1464619867) ![lcds___displays_gopro-screw.jpg](https://cdn-learn.adafruit.com/assets/assets/000/032/821/medium640/lcds___displays_gopro-screw.jpg?1464619889) ![](https://cdn-learn.adafruit.com/assets/assets/000/032/816/medium800/lcds___displays_gopro-complete.jpg?1464619339) ## Fly Safe! Make sure to complete charge the battery before flying!  ## Related Guides - [Adafruit Powerboost 1000C](https://learn.adafruit.com/adafruit-powerboost-1000c-load-share-usb-charge-boost.md) - [CLUE Step Counter](https://learn.adafruit.com/clue-step-counter-st-lsm6ds33.md) - [Four Channel Audio Passive Stereo Mixer](https://learn.adafruit.com/four-channel-audio-passive-stereo-mixer.md) - [Infrared Hand Gesture Robot Control Glove](https://learn.adafruit.com/cpx-ir-infrared-hand-gesture-robot-control-glove.md) - [Prop-Maker Feather Talking Adabot Clock](https://learn.adafruit.com/prop-maker-feather-talking-adabot-clock.md) - [Talking D20 with RP2040 PropMaker Feather](https://learn.adafruit.com/talking-d20-rp2040.md) - [CircuitPython Painter](https://learn.adafruit.com/circuitpython-painter.md) - [Sparkle Motion Dance Shoes](https://learn.adafruit.com/sparkle-motion-dance-shoes.md) - [Motion Sensor Bat](https://learn.adafruit.com/motion-sensor-bat.md) - [IoT Food Scale with Azure and CircuitPython](https://learn.adafruit.com/iot-food-scale-with-azure-and-circuitpython.md) - [LED Noodle Lamp](https://learn.adafruit.com/led-noodle-lamp.md) - [Superhero Power Gauntlet](https://learn.adafruit.com/superhero-power-gauntlet.md) - [Glider Paper Airplane Controller](https://learn.adafruit.com/glider-paper-airplane-controller.md) - [CircuitPython BLE Advertising Beacons](https://learn.adafruit.com/circuitpython-ble-advertising-beacons.md) - [Pyloton: CircuitPython Cycling Computer](https://learn.adafruit.com/pyloton.md) - [Zelda: Breath of the Wild – 3D Printed Bladesaw](https://learn.adafruit.com/bladesaw.md)