# Adafruit Feather RP2040 RFM69 ## Overview ![](https://cdn-learn.adafruit.com/assets/assets/000/120/017/medium800/adafruit_products_FRPRFM69_top.jpg?1680294195) This is the **Adafruit Feather RP2040 RFM69 Packet Radio (868 or 915 MHz).** We call these _RadioFruits **,** _ our take on an microcontroller with packet radio transceiver with built-in USB and battery charging. It's an Adafruit Feather RP2040 with a RFM69HCW 900MHz radio module cooked in! Great for making wireless networks that are more flexible than Bluetooth LE and without the high power requirements of WiFi. Feather is the development board specification from Adafruit, and like its namesake, it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores. [We have other boards in the Feather family, check'em out here](https://www.adafruit.com/feather). ![](https://cdn-learn.adafruit.com/assets/assets/000/120/018/medium800/adafruit_products_FRPRFM69_back.jpg?1680294255) It's kinda like we took our [RP2040 Feather](https://www.adafruit.com/product/4884) and [RFM69 900MHz breakout board](https://www.adafruit.com/product/3070) and glued them together. You get all the pins for use on the Feather, the Lipoly battery support, USB C power / data, onboard NeoPixel, 8MB of FLASH for storing code and files, and then with the 8 unused pins, we wired up all the DIO pins on the RFM module. There's even room left over for a STEMMA QT connector an a uFL connector for connecting larger antennas. **This is the 900 MHz RFM69 packet radio version, which can be used for either 868MHz or 915MHz transmission/reception** - the exact radio frequency is determined when you load the software since it can be tuned around dynamically. Despite calling it a 'packet' radio (and it does send packets of data) the RFM69 can also be used for non-packetized radio transmission and reception. ![](https://cdn-learn.adafruit.com/assets/assets/000/120/019/medium800/adafruit_products_FRPRFM69_USB_C_end.jpg?1680294269) At the Feather's heart is an RP2040 chip, clocked at 133 MHz and at 3.3V logic, the same one used in the [Raspberry Pi Pico](https://www.adafruit.com/product/4864). This chip has a whopping 8MB of onboard QSPI FLASH and 264K of RAM! This makes it great for making wireless sensor nodes that can send to each other without a lot of software configuration. To make it easy to use for portable projects, we added a connector for any of our 3.7V Lithium polymer batteries and built-in battery charging. You don't need a battery, it will run just fine straight from the USB Type C connector. But, if you do have a battery, you can take it on the go, then plug in the USB to recharge. The Feather will automatically switch over to USB power when its available. **Here're some handy specs! You get:** - Measures 52.2mm x 23.0mm x 7.3mm / 2.1" x 0.9" x 0.3" without headers soldered in - Light as a (large?) feather - 6 grams - RP2040 32-bit Cortex M0+ dual core running at ~133 MHz @ 3.3V logic and power - 264 KB RAM - **8 MB SPI FLASH**  chip for storing files and CircuitPython/MicroPython code storage. No EEPROM - **Tons of GPIO! 21 x GPIO pins with following capabilities:** - **Four ** 12-bit ADCs (one more than Pico) - Two I2C, Two SPI, and two UART peripherals, we label one for the 'main' interface in standard Feather locations - 16 x PWM outputs - for servos, LEDs, etc - **Built-in 200mA+ lipoly charger**  with charging status indicator LED - **Pin #13 red LED ** for general purpose blinking - **RGB NeoPixel**  for full-color indication. - On-board  **STEMMA QT connector**  that lets you quickly connect any Qwiic, STEMMA QT or Grove I2C devices with no soldering! - **Both Reset button and Bootloader select button for quick restarts ** (no unplugging-replugging to relaunch code) - **USB Type C connector ** lets you access built-in ROM USB bootloader and serial port debugging - 3.3V Power/enable pin - 4 mounting holes - 12 MHz crystal for perfect timing. - 3.3V regulator with 500mA peak current output ![](https://cdn-learn.adafruit.com/assets/assets/000/120/020/medium800/adafruit_products_FRPRFM69_top_headers.jpg?1680294300) We squished all the parts on our Feather RP2040 over towards the USB port to make some room on the end. This  **Feather RP2040 Packet** **Radio**  uses the extra space left over to add an RFM69HCW high power 868/915 MHz radio module. These radios are not good for transmitting audio or video, but they do work quite well for small data packet transmission when you need more range than 2.4 GHz (BT, BLE, WiFi, ZigBee). Radio module specifications: - SX1231 based module with SPI interface - +13 to +20 dBm up to 100 mW Power Output Capability (power output selectable in software) - 50mA (+13 dBm) to 150mA (+20dBm) current draw for transmissions, ~30mA during active radio listening. - Range of approx. 500 meters, depending on obstructions, frequency, antenna and power output - Create multipoint networks with individual node addresses - Encrypted packet engine with AES-128 - Packet radio with ready-to-go Arduino & CircuitPython libraries - Uses the license-free ISM band: "European ISM" @ 868MHz or "American ISM" @ 915MHz - Simple wire antenna can be soldered into a solder pad, there's also a [uFL connector that can be used with uFL-to-SMA adapters](https://www.adafruit.com/product/851) for attaching bigger antennas. Our initial tests with default library settings indicate they can go at least 500 meters line of sight using simple wire antennas, probably up to 5Km with directional antennas and tweaking some settings. ![](https://cdn-learn.adafruit.com/assets/assets/000/120/024/medium800/adafruit_products_FRPRFM69_spring_antenna.jpg?1680294797) Comes fully assembled and tested, we also toss in some headers so you can solder it in and plug into a solderless breadboard. You will need to cut and solder on a small piece of wire (any solid or stranded core is fine) in order to create your antenna. or use a uFL connector and SMA 900MHz antenna.  **Lipoly battery and USB cable are not included,**  but we do have lots of options in the shop if you'd like! ![](https://cdn-learn.adafruit.com/assets/assets/000/120/026/medium800/adafruit_products_FRPRFM69_battery.jpg?1680294989) - [Next Page](https://learn.adafruit.com/feather-rp2040-rfm69/pinouts.md) ## Primary Products ### Adafruit Feather RP2040 RFM69 Packet Radio - 868 or 915MHz [Adafruit Feather RP2040 RFM69 Packet Radio - 868 or 915MHz](https://www.adafruit.com/product/5712) This is the **Adafruit Feather RP2040 RFM69 Packet Radio (868 or 915 MHz).** We call these _RadioFruits **,** _ our take on an microcontroller with packet radio transceiver with built-in USB and battery charging. It's an Adafruit... In Stock [Buy Now](https://www.adafruit.com/product/5712) [Related Guides to the Product](https://learn.adafruit.com/products/5712/guides) ## Guide Products ### STEMMA QT / Qwiic JST SH 4-pin Cable - 100mm Long [STEMMA QT / Qwiic JST SH 4-pin Cable - 100mm Long](https://www.adafruit.com/product/4210) This 4-wire cable is a little over 100mm / 4" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. In Stock [Buy Now](https://www.adafruit.com/product/4210) [Related Guides to the Product](https://learn.adafruit.com/products/4210/guides) ### STEMMA Wired Potentiometer Breakout Board - 10K ohm Linear [STEMMA Wired Potentiometer Breakout Board - 10K ohm Linear](https://www.adafruit.com/product/4493) For the easiest way possible to measure twists, turn to this STEMMA potentiometer breakout (ha!). This plug-n-play pot comes with a JST-PH 2mm connector and a matching  [JST PH 3-Pin to Male Header Cables - 200mm](https://www.adafruit.com/product/3893), so wiring up is a cinch.... In Stock [Buy Now](https://www.adafruit.com/product/4493) [Related Guides to the Product](https://learn.adafruit.com/products/4493/guides) ### Adafruit MCP9808 High Accuracy I2C Temperature Sensor Breakout [Adafruit MCP9808 High Accuracy I2C Temperature Sensor Breakout](https://www.adafruit.com/product/5027) The MCP9808 digital temperature sensor is one of the more accurate/precise we've ever seen, with a typical accuracy of ±0.25°C over the sensor's -40°C to +125°C range and precision of +0.0625°C. They work great with any microcontroller using standard I2C. With... In Stock [Buy Now](https://www.adafruit.com/product/5027) [Related Guides to the Product](https://learn.adafruit.com/products/5027/guides) ### Adafruit I2S 3W Class D Amplifier Breakout - MAX98357A [Adafruit I2S 3W Class D Amplifier Breakout - MAX98357A](https://www.adafruit.com/product/3006) Listen to this good news - we now have an all in one digital audio amp breakout board that works incredibly well with the [Raspberry Pi](https://www.adafruit.com/category/105)! If you're looking for an easy and low cost way to get your digital sound files... In Stock [Buy Now](https://www.adafruit.com/product/3006) [Related Guides to the Product](https://learn.adafruit.com/products/3006/guides) ### Mono Enclosed Speaker with Plain Wires - 3W 4 Ohm [Mono Enclosed Speaker with Plain Wires - 3W 4 Ohm](https://www.adafruit.com/product/4445) Listen up! This single  2.8" x 1.2" speaker is the perfect addition to any audio project where you need 4 ohm impedance and 3W or less of power. We particularly like these speakers as they are small and enclosed for good audio volume and quality. This speaker _does..._ Out of Stock [Buy Now](https://www.adafruit.com/product/4445) [Related Guides to the Product](https://learn.adafruit.com/products/4445/guides) ### Premium Male/Male Jumper Wires - 20 x 6" (150mm) [Premium Male/Male Jumper Wires - 20 x 6" (150mm)](https://www.adafruit.com/product/1957) These Male/Male Jumper Wires are handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 6" (150mm) long and come in a 'strip' of 20 (2 pieces of each of ten rainbow colors). They have 0.1" male header contacts on either... In Stock [Buy Now](https://www.adafruit.com/product/1957) [Related Guides to the Product](https://learn.adafruit.com/products/1957/guides) ### NeoPixel Ring - 16 x 5050 RGB LED with Integrated Drivers [NeoPixel Ring - 16 x 5050 RGB LED with Integrated Drivers](https://www.adafruit.com/product/1463) Round and round and round they go! 16 ultra bright smart LED NeoPixels are arranged in a circle with 1.75" (44.5mm) outer diameter. The rings are 'chainable' - connect the output pin of one to the input pin of another. Use only one microcontroller pin to control as many as you can... In Stock [Buy Now](https://www.adafruit.com/product/1463) [Related Guides to the Product](https://learn.adafruit.com/products/1463/guides) ## Related Guides - [Adafruit NeoPixel Überguide](https://learn.adafruit.com/adafruit-neopixel-uberguide.md) - [Adafruit MAX98357 I2S Class-D Amps - Stereo and Mono](https://learn.adafruit.com/adafruit-max98357-i2s-class-d-mono-amp.md) - [Adafruit BME680](https://learn.adafruit.com/adafruit-bme680-humidity-temperature-barometic-pressure-voc-gas.md) - [No-Code, No-Solder Monitoring For Perfect Bread](https://learn.adafruit.com/no-code-no-solder-temperature-monitoring-with-wippersnapper-offline.md) - [CircuitPython Libraries on any Computer with FT232H](https://learn.adafruit.com/circuitpython-on-any-computer-with-ft232h.md) - [Adafruit Feather RP2040 with USB Type A Host](https://learn.adafruit.com/adafruit-feather-rp2040-with-usb-type-a-host.md) - [An Introduction to RP2040 PIO with CircuitPython](https://learn.adafruit.com/intro-to-rp2040-pio-with-circuitpython.md) - [Soundbox RP2040](https://learn.adafruit.com/soundbox-rp2040.md) - [Velociraptor Voice and Eye Upgrade with MONSTER M4SK](https://learn.adafruit.com/hand-puppet-voice-and-eye-upgrade-with-monster-m4sk.md) - [IoT Food Scale with Azure and CircuitPython](https://learn.adafruit.com/iot-food-scale-with-azure-and-circuitpython.md) - [Toddler Timer](https://learn.adafruit.com/toddler-timer.md) - [CircuitPython Powered Sip & Puff with ST LPS33HW Pressure Sensor](https://learn.adafruit.com/st-lps33-and-circuitpython-sip-and-puff.md) - [Arcade Synth Controller](https://learn.adafruit.com/arcade-synth-controller.md) - [Talking HAL 9000 with RP2040 Prop Maker Feather](https://learn.adafruit.com/hal-9000-rp2040-prop-maker.md) - [Adafruit QT Py ESP32-S3](https://learn.adafruit.com/adafruit-qt-py-esp32-s3.md) - [Fruit Jam Nintendo Entertainment System and Retro Jam](https://learn.adafruit.com/fruit-jam-nintendo-entertainment-system.md) - [Voicebox FX](https://learn.adafruit.com/voicebox-fx.md)