# How to Polish copperFill & bronzeFill Filament
## Overview
https://www.youtube.com/watch?v=AU8WvGveNj4
copperFill and bronzeFill are metal infused 3D printer filament. copperFill has a bit of a browner, more rustic look than its bronze counterpart, once polished.
Produced with a micronized copper powder which has been infused into a common PLA plastic, copperFill will print easily using an all metal hot-end. Colorfabb warns against using any hot-ends which use a teflon isolator coupler, as the filament has been shown to clog these devices.
After polishing, prints look like they were cast in metal. In this guide we'll look at achiving super shiny results, without any liquids or futhers preperations on your part.
# How to Polish copperFill & bronzeFill Filament
## Usage
## Temperature Guidelines:
copperFill and bronzeFill prints with your standard PLA settings. Heated bed is not required. For a good adhesion to the platform, we recommend blue painter's tape.
Recommended settings:
- extruder temperature: 190 - 225°C
- platform temperature: 0 - 50°C
- shells: 2 - 4
- resolution: .1mm
- infill: 10%-50%
[Download Printer Profiles](https://github.com/djecken/3d-printer-profiles)
## Compatible Extruders
Direct drive and bowden extruders systems are compaitable with both materials. Colorfabb warns against using any hot-ends which use a teflon isolator coupler, as the filament has been shown to clog these devices.
## Resolution
Higher resolutions of 100 microns will help get a smoother shine quicker, without the risk of leaving the part in the tumbler for too long. 200 microns will leave ridges where the layers meet, making it more difficault to smooth out later.
## Cleaning Prints
Use flush diagonal cutters and a hobby knife to remove the excess material left behind during printing. You can use your fingers to rub away the loose bits. Use a hobby knife to get in between crevices and remove tiny artifacts.
## Tumbling medium
Abrasive material is needed to help bring out the copper metal shine. We used brass screws of different sizes for surface finishing, deburring and polishing. Use wood brass screws sizes #00 to get into the small nooks and crannies of parts, while #2, #4, #6 are used for bigger areas of the model. You'll want to use a good amount of screws - about 50 to 100 screws should be enough to get a good shine. Water or any other liquid is not required.
## Tumbler
This 3 lbs [tumbler](http://www.amazon.com/gp/product/B000RB16W8) can hold prints that are 90mm tall by 85mm wide. Tumble times vary depeding on how big and complex the model is.
Small prints (20mm x 20mm): 6 hours
Medium prints (80mm x 30mm): 18 hours
Large prints (90mm x 85mm) 36 hours
You’ll want to periodically check (about once an hour) on your print to make sure it’s still in one piece.
## Clean Up
Avoid getting dust on your hands, be sure to use gloves to remove your parts after tumbling as the screws grind together and create metal particles. Use a brush and shop towel to clean off the rest of the dust and particles. Be sure to clean in a well ventilated area.
## Before and After
If the model doesn't make it out of the tumbler in one piece, don't worry, some models can easily be glued back together. You can also try using more shells/parameters to strength the model and try again!
# How to Polish copperFill & bronzeFill Filament
## Properties
## Retraction
High speeds for retraction can cause the metal filament to clog. Burrs are easy to clean off with your finger or hobby knife. Try to clean as much as you can. Tumbling will smooth out the surface but any larger bumps will only get smoothed out into a blob.
## Weight
Parts are heavy compared to PLA prints. The bust pictured above measures 72mm tall x 85mm wide and weighs 80 grams. The same print in PLA weights only 12 grams! Both have 2 shells and 10% infill.
## Strength
copperFill has enough flexablity to withstand extreme bends. Applying force will deform the model. When parts break, they slowly tear before snapping.
# How to Polish copperFill & bronzeFill Filament
## Tips
## Sanding
We've seen great examples using steel wool to polish, but in our test sanding brought out PLAs white color. Polishing compound (Brasso) can also be used to get a patina look on the model.
## High Resolution
Use 100 microns or higher to achive a smooth finish. Lower resolutions will take more time to smooth out. The longer the model tumbles, the more likely parts will brake.
## Metal Wear
Brass screws wears down after about 120 hours of tumbling. Screws grind and then the metal particles stick to parts, giving them a brilliant shine. We recommend using new screws to help maintain a consistent polish.
## Featured Products
### Type A Machines Series 1 Pro 3D Printer
[Type A Machines Series 1 Pro 3D Printer](https://www.adafruit.com/product/2412)
Built to last and better than ever. The **Series 1 Pro 3D** printers from Type A Machines offer durability, modularity and one of the largest build volumes in their class.
Featuring a streamlined aluminum and acrylic body, a glass build surface...
No Longer Stocked
[Buy Now](https://www.adafruit.com/product/2412)
[Related Guides to the Product](https://learn.adafruit.com/products/2412/guides)
### PrintrBot Simple Metal 3D Printer - Black - Assembled
[PrintrBot Simple Metal 3D Printer - Black - Assembled](https://www.adafruit.com/product/1760)
New from Printrbot, the Metal Simple is a brand new rock solid, all metal, fully-assembled Printrbot Simple! As opposed to the [Printrbot Simple Kit](http://www.adafruit.com/products/1735), all of the laser cut wood parts have been replaced by rock solid metal and assembled. In...
No Longer Stocked
[Buy Now](https://www.adafruit.com/product/1760)
[Related Guides to the Product](https://learn.adafruit.com/products/1760/guides)
### PrintrBot Metal PLUS 3D Printer - Black Assembled
[PrintrBot Metal PLUS 3D Printer - Black Assembled](https://www.adafruit.com/product/2302)
New from Printrbot, the Metal Plus is a rock solid, all metal, fully-assembled beast of a printer!
The new **Printrbot Metal Plus w/ Heated Bed** is constructed of powder coated metal and machined aluminum with open platform for fabricating parts up to 10 x 10 x 10...
No Longer Stocked
[Buy Now](https://www.adafruit.com/product/2302)
[Related Guides to the Product](https://learn.adafruit.com/products/2302/guides)
### Printrbot Simple Kit - 1405 Model
[Printrbot Simple Kit - 1405 Model](https://www.adafruit.com/product/1735)
The Printrbot Simple is an exercise in 3D printing minimalism. It includes only what is needed to get started in the world of 3D printing. After building this kit you'll have a fully-functioning 3D printer that weighs only 10 lbs and fits nicely on your desk
**Please...**
No Longer Stocked
[Buy Now](https://www.adafruit.com/product/1735)
[Related Guides to the Product](https://learn.adafruit.com/products/1735/guides)
### ORION™ Delta 3D Printer - Black
[ORION™ Delta 3D Printer - Black](https://www.adafruit.com/product/2259)
The ORION™ Delta 3D Printer is an exciting and attractive new 3D printer from the folks at SeeMe CNC that's designed to print ABS, PLA, and other materials from the very beginning. There's no need to refine or do anything to your printer - so you really have a ton more options for...
No Longer Stocked
[Buy Now](https://www.adafruit.com/product/2259)
[Related Guides to the Product](https://learn.adafruit.com/products/2259/guides)
### PLA/PHA copperFill for 3D Printers - 1.75mm Diameter - 750g
[PLA/PHA copperFill for 3D Printers - 1.75mm Diameter - 750g](https://www.adafruit.com/product/2128)
Having a 3D printer without filament is sort of like having a regular printer without paper or ink. And while a lot of printers come with some filament there's a good chance you've been printing up a storm and need something new. That's why we've started carrying
No Longer Stocked
[Buy Now](https://www.adafruit.com/product/2128)
[Related Guides to the Product](https://learn.adafruit.com/products/2128/guides)
### PLA/PHA bronzeFill for 3D Printers - 1.75mm Diameter - 750g
[PLA/PHA bronzeFill for 3D Printers - 1.75mm Diameter - 750g](https://www.adafruit.com/product/1830)
Having a 3D printer without filament is sort of like having a regular printer without paper or ink. And while a lot of printers come with some filament there's a good chance you've been printing up a storm and need something new. That's why we've started carrying
No Longer Stocked
[Buy Now](https://www.adafruit.com/product/1830)
[Related Guides to the Product](https://learn.adafruit.com/products/1830/guides)
### PRINTinZ Flexible 3D Printer Plate for Printrbot - 168mm x 237mm
[PRINTinZ Flexible 3D Printer Plate for Printrbot - 168mm x 237mm](https://www.adafruit.com/product/2233)
Removing 3D printed parts from your 3D printer can be tough. Sometimes pieces get stuck to your 3D printing plate and their bottoms get stuck to your build plate. Over time, chiseling objects off can scratch and damage your plate - and get pretty annoying - so wouldn't it be...
No Longer Stocked
[Buy Now](https://www.adafruit.com/product/2233)
[Related Guides to the Product](https://learn.adafruit.com/products/2233/guides)
## Related Guides
- [Magnetic shoelaces](https://learn.adafruit.com/magnetic-shoelaces.md)
- [Desktop Fume Extractor](https://learn.adafruit.com/desktop-fume-extractor.md)
- [NeoTrellis M4 Bumper](https://learn.adafruit.com/neotrellis-m4-bumper.md)
- [No-Code Pool Party Notifier](https://learn.adafruit.com/pool-party-notification-device.md)
- [3D Printed D20 Molds](https://learn.adafruit.com/3d-printed-d20-molds.md)
- [Feather Fingerboard](https://learn.adafruit.com/feather-fingerboard.md)
- [3D Printed Valentine with Bare Conductive Electric Paint](https://learn.adafruit.com/3d-printed-valentine-with-bare-conductive-electric-paint.md)
- [3D Printed Custom Keycaps](https://learn.adafruit.com/3dprinted-custom-keycaps.md)
- [Genesis Poi: DotStar LED Persistence-of-Vision](https://learn.adafruit.com/genesis-poi-dotstar-led-persistence-of-vision-poi.md)
- [IoT Filament Sensor](https://learn.adafruit.com/iot-filament-sensor.md)
- [Purple People Eater](https://learn.adafruit.com/purple-people-eater.md)
- [Qualia S3 Fireplace](https://learn.adafruit.com/qualia-s3-fireplace.md)
- [OctoPrint - Open Source Host Software](https://learn.adafruit.com/octoprint-open-source-host-software.md)
- [iPad Pro Bumper](https://learn.adafruit.com/ipad-pro-bumper.md)
- [Solder Dispenser Adabot Head](https://learn.adafruit.com/solder-dispenser-adabot-head.md)