This is for people who just want to get cold fast. The 12V Peltier module is mounted onto a 12V heatsink and fan assembly with thermal paste and an aluminum clamp. Simply connect to 12V 5A+ power supply and you will see frost appear on the aluminum plate within a minute. This assembly comes...

Put a temperature meter anywhere with this very handy display. This panel meter displays the temperature of the attached waterproof 1% thermistor in °C. It does require a DC voltage to run, at 4.5-30VDC. It has reverse polarity protection in case you swap the power leads by accident.

Move fluid safely from here to there with this very nice little pump. Unlike most liquid pumps, this is a peristaltic type - the pump squishes the silicone tubing that contains the liquid instead of impelling it directly. The upshot?...

Fire up your engines because these are the hot-rods of toggle switches! Equipped with an aerodynamic clear protective casing, and a diffused white LED at the tip of the switch, this Clear/White LED Toggle Switch is sure to add some flair (and flare!) to your...

These chrome-plated metal buttons are rugged and look real good while doing it! Simply drill a 16mm hole into any material up to 1/2" thick and you can fit these in place, there's even a rubber gasket to keep water out of the enclosure. On the front of the button is a flat metal...

This is a beefy switching supply, for when you need a lot of power! It can supply 12V DC up to 5 Amps, running from 110V or 220V power (the plug it comes with is for US/Canada/Japan but you can use any plug adapter for your country, or just replace the cable with a standard 'figure-8'...

If you need to connect a DC power wall wart to a board that doesn't have a DC jack - this adapter will come in very handy! There is a 2.1mm DC jack on one end, and a screw terminal block on the other. The terminals are labeled with positive/negative assuming a positive-tip configuration...

Our all-in-one 5V 2.5 Amp + MicroUSB cable power adapter is the perfect choice for powering single-board computers like Raspberry Pi, BeagleBone, or anything else that's power-hungry!This adapter was specifically designed to provide 5.25V, not 5V, but we still call it a 5V USB...

When you need to switch a lot of power, N-channel MOSFETs are best for the job. These FETs can switch over 60A and 30V and are TO-220 packages so they fit nicely into any breadboard or perfboard. Heat sinking is easy with TO-220's, but because of the very low Rds(on) of down to 0.009 ohms...

Get that heat sink stuck on good and strong with 3M's thermal tape. Specifically designed for attaching heat sinks to ICs. Works better and is less messy than thermal glues or pastes because the thickness is even across the area. A perfect match for our range of small heat sinks, either in...

Customers have asked us to carry basic perf-board, but we never liked the look of most basic perf: it's always crummy quality, with pads that flake off and no labeling. Then we thought about how people actually prototype - usually starting with a solderless breadboard and...

Totaling 380 pieces, this M2.5 Screw Set is a must-have for your workstation. You'll have enough screws, nuts, and hex standoffs to fuel your maker tendencies for days on end! M2.5 size screws fit almost all of the Adafruit breakout/dev board mounting holes...

This here is your standard A to micro-B USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your Metro, Feather, Raspberry Pi or other dev-board or microcontrollerApproximately 3 feet / 1 meter long

This here is a 10 pack of the classic 1N4001 power blocking diode. These are good for reverse polarity protection (put it between your DC power jack and circuitry to avoid a negative-voltage that would zap your delicate electronics), kickback protection (place across your solenoids, relays...

LEDs and passives and transistors and switches and op-amps oh my! The...