Use a Gemma M0 and a couple of LEDs to make this Princess Peach / Bowsette inspired crown! Use Circuit Python to fade the 10mm LEDs inside the translucent filament to illuminate this magical mushroom inspired crown. 

 

Top it off with a pair of our flexible printed horns to create a unique twist on the Bowsette crown!

The crown is 3d printed in flexible material, making it easy for cut or sew onto fabrics, perfect for cosplay.

 

The Gems are 3d printed in a translucent material that allows it to fully diffuse. 

 

The horns are printed in glow in the dark flexible material, so the look spooky under blavk uv lights!

 

3D print or use an existing headband to wear for your next halloween or cosplay event!

Prerequisite Guides

 

If you're new to Adafruit Circuit Python and soldering, take a moment to walk through the following guides to get you started.

 

Tools and Supplies

List of handy things to assist in any project.

Pink polished fingers holding a Adafruit GEMMA M0 - Miniature wearable electronic platform.
The Adafruit Gemma M0 is a super small microcontroller board, with just enough built-in to create many simple projects. It may look small and cute: round, about the...
$9.95
In Stock
Lithium Ion Polymer Battery 3.7v 150mAh with JST 2-PH connector
Lithium-ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light, and powerful. The output ranges from 4.2V when completely charged to 3.7V. This...
$5.95
In Stock
Top view of Adafruit Micro Lipo - USB LiIon/LiPoly charger - v1 above a 2-pin JST cable.
Oh so adorable, this is the tiniest little lipo charger, so handy you can keep it any project box! Its also easy to use. Simply plug in the gold plated contacts into any USB port and a...
$5.95
In Stock
Spool of NinjaFlex Filament for 3D Printers - satin sheen gold color with 1.75mm Diameter.
Looking beyond ABS? Tired of PLA? Open a world of possibilities, limited only by your imagination. NinjaFlex, a cutting-edge filament for 3D printers, is a specially formulated...
Out of Stock
Angled shot of 25 Through-Hole Resistors - 220 ohm 5% 1/4W.
ΩMG! You're not going to be able to resist these handy resistor packs! Well, axially, they do all of the resisting for you!This is a 25 Pack of...
$0.75
In Stock
Angled shot of Premium Male/Female Raw Jumper Wires - 40 x 6
Our Raw Male/Female Jumper Wires are perfect for making a custom jumper wire sets for wire harnesses or jumpering between headers on PCBs. These premium jumpers are a little...
$2.95
In Stock
Single large LED lit up red
Need some big indicators? We are big fans of these huge diffused red LEDs. They are fairly bright so they can be seen in daytime, and from any angle. They go easily into a breadboard...
$9.95
In Stock
Single large LED lit up blue
Need some big indicators? We are big fans of these huge diffused blue LEDs. They are really bright so they can be seen in daytime, and from any angle. They go easily into a breadboard...
$9.95
In Stock
Single large LED lit up yellow
Need some big indicators? We are big fans of these huge diffused yellow LEDs. They are fairly bright so they can be seen in daytime, and from any angle. They go easily into a...
$9.95
In Stock
Single large LED lit up green
Need some big indicators? We are big fans of these huge 10mm diffused green LEDs. They are fairly bright so they can be seen in daytime, and from any angle. They go easily into a...
$4.95
In Stock
Monoprice Inventor II 3D Printer with Touchscreen and WiFi
The Monoprice Inventor II 3D Printer Touchscreen with WiFi is a perfect entry-level 3D printer with small footprint and reliable performance. It comes equipped with...
Out of Stock

This guide was first published on Oct 03, 2018. It was last updated on Oct 03, 2018.

This page (Overview) was last updated on Aug 05, 2022.

Text editor powered by tinymce.