# BioShock little sister syringe ## Overview https://youtu.be/xG69449QZUY ![](https://cdn-learn.adafruit.com/assets/assets/000/023/967/medium800/components_hero-sit-point.jpg?1426713807) ## Making Cosplay Props with 3D Printing + DIY Electronics Build a creepy cosplay prop with a 3D printing, copper filament and simple electronics! This prop features a built-in trigger that actuates a momentary push button to make an eerie red glow. This guide will walk you through the steps of 3d printing, polishing, soldering and assembling of this project. ## Project Expectations This project is geared towards makers who have basic 3D printing skills and access to a 3D printer. The circuit is very beginner friendly and easily to solder. The 3D parts were designed for large build platforms. The large parts can be split to fit smaller pieces using a tool like MeshMixer from Autodesk. Printing these parts can take up to 24 hours and   about 100 grams of material. ![](https://cdn-learn.adafruit.com/assets/assets/000/023/968/medium800/components_tools.jpg?1426714319) ## Parts Below is a full list of parts needed to build this project. Be sure to check out the featured products on the right sidebar. - [PLA Filament](https://www.adafruit.com/search?q=ninjaflex "Link: https://www.adafruit.com/search?q=ninjaflex") - [3D Printer ](https://www.adafruit.com/search?q=3d+printer "Link: https://www.adafruit.com/search?q=3d+printer") - [copperFill](https://www.adafruit.com/products/2128) - [NinjaFlex](https://www.adafruit.com/product/2382) - [Blue tape](https://www.adafruit.com/products/2416) - [Rechargable coin cell](https://www.adafruit.com/products/1572) - [Copper foil tape](https://www.adafruit.com/product/1128) - [10mm LED](https://www.adafruit.com/product/845) - [6mm Tactile button](https://www.adafruit.com/product/367) - [#2-56 3/8 phillips screws](https://www.amazon.com/gp/product/B000MN6P90) ## Tools & Supplies You'll need a couple of hand tools and accessories to assist you in the build.  - [Hakko Flat Pliers](https://www.adafruit.com/product/1368) - [Flush diagonal cutter](https://www.adafruit.com/product/152) - [Scissors](https://www.adafruit.com/product/1599) - [Knife jimmy](https://www.adafruit.com/products/2414), [Spatula](http://amzn.com/B00409PJGW) or [Palette Knife](http://amzn.com/B00DUI6E7C)  - [Dremel polishing kit](http://amzn.com/B002L3RV4M) ![](https://cdn-learn.adafruit.com/assets/assets/000/023/969/medium800/components_partsB.jpg?1426714227) # BioShock little sister syringe ## Circuit Diagram ![](https://cdn-learn.adafruit.com/assets/assets/000/024/052/medium800/components_circuit-diagram.jpg?1426907965) **10mm LED** The long pin is soldered to the (red) positive wire. The other end of the red wire is soldered to copper tape. The piece of copper is tapped to the postive side of the coin cell battery.  The short pin is soldered to a shorter (blue) negative wire.  The other end is soldered to the tactile button. **6mm Tactile Button** A longer (blue) negative wire is soldered to another one of the leads on the button. The short (blue) wire is soldered to lead on the button. The two wires on the button should be diagonally apart. **LIR2450 Coin Cell Battery** Copper tape has an adhesive backing, peel a small portion and stick it on the positive and negative side of the coin cell battery. Leave some of the backing on so the copper doesn’t touch the side of the battery. # BioShock little sister syringe ## 3D Printing ## PLA Filament These parts are optimized for printing in copperFill and PLA material. The parts print best **without** any supports! ![](https://cdn-learn.adafruit.com/assets/assets/000/023/970/medium800/components_3d-parts-sm.jpg?1426723076) [Download STLs on Cults3D](https://cults3d.com/en/gadget/little-sisters-syringe) [Download STLs on Thingiverse](http://www.thingiverse.com/thing:737560) ## Slicing Software The recommend settings above should work with most slicing software. However, you are encouraged to use your own settings since 3D printers and slicing software will vary from printer to printer. ![](https://cdn-learn.adafruit.com/assets/assets/000/023/992/medium800/components_btn_slot_clean_up.jpg?1426734396) ## Clean up Prepare the cavity for the tactile button by removing any material around the actuator. It should freely move when the triggger handle is squeezed. ![](https://cdn-learn.adafruit.com/assets/assets/000/023/995/medium800/components_btn_slot_cleaned.jpg?1426749865) ## Test snap fit Use a hobby knife to remove any material around the walls of the cavity and then test fit the snap fit tolerance with the 6mm tactile button. ![](https://cdn-learn.adafruit.com/assets/assets/000/023/993/medium800/components_tap_start.jpg?1426734431) ## Prepare standoffs Tweezers or a small screw driver can be used to slightly enlarge the mounting holes for the standoffs. This will make it easier to create the threads inside the standoffs. ![](https://cdn-learn.adafruit.com/assets/assets/000/023/994/medium800/components_screw.jpg?1426739162) ## Thread mouting holes Use #2-56 3/8 screws and small screw driver to create the threads inside the standoffs. Danger: # BioShock little sister syringe ## Polishing ![](https://cdn-learn.adafruit.com/assets/assets/000/023/973/medium800/components_drill-bits.jpg?1426718777) ## Polishing brushes and buffs The white detail abrasive brush, the 280 and 320 grit abrasive buff found in the Dremel polishing kit had the best polishing results. ![](https://cdn-learn.adafruit.com/assets/assets/000/024/002/medium800/components_dremel-speed.jpg?1426735714) ## Polishing speeds Use the slowest speed on your rotray power tool to polish the surface without damaging base layer. ![](https://cdn-learn.adafruit.com/assets/assets/000/023/974/medium800/components_polish-start.jpg?1426718825) ## Polishing techniques Start with the 280 grit (it's the hardest brush to squeeze.) Use the slowest speeds on the Dremel and begin smoothing out the layers by blending them together. Use a back and forth motion as you polish along the seams.  ![](https://cdn-learn.adafruit.com/assets/assets/000/024/003/medium800/components_polish.jpg?1426736004) Focus on one section at a time, try to blend the layers together and go back over sections to even out the surface. After smoothing out the ridges from the surface, polish each area a second time to bring out more of a metalic shine. ![](https://cdn-learn.adafruit.com/assets/assets/000/023/978/medium800/components_polish_small_brush.jpg?1426727832) Switch to the white abrasive brush for the contours and hard-to-reach areas. ![](https://cdn-learn.adafruit.com/assets/assets/000/023/979/medium800/components_polish-compound.jpg?1426727849) ## Polishing compound The Dremel polishing kit includes a polishing compound. Apply to the surface using gloves. Rub it into the surface to fill in any holes. ![](https://cdn-learn.adafruit.com/assets/assets/000/023/980/medium800/components_polish-compound-buff.jpg?1426744437) ## Buff Use the 320 grit abrasive buff to finish and smooth out the surface. The buff really adds contrasting tones to the overall look of the parts. ![](https://cdn-learn.adafruit.com/assets/assets/000/023/981/medium800/components_polish-compare.jpg?1426721364) ## Comparision  Comparing the surfaces of these parts you can really see how well the polished part comes out. Definitely worth the time finishing your copperFill prints. A great alternative to the rotary tumbler. # BioShock little sister syringe ## Assembly ![](https://cdn-learn.adafruit.com/assets/assets/000/023/972/medium800/components_wire_measure.jpg?1426755697) ## Measure wires Lay the wire on top of the handle part and measure how long each wire needs to be for the button, LED and battery. ![](https://cdn-learn.adafruit.com/assets/assets/000/023/982/medium800/components_copper_tape_wire_solder.jpg?1426719498) ## Tin wires and copper tape Measure a piece of copper tape. Be careful not to remove the backing. Use a helping-third-hand to asist while tinning. Add a small blob of solder to tape and then solder the measured silicone-coated wire to the ends of the tape. ![](https://cdn-learn.adafruit.com/assets/assets/000/023/984/medium800/components_LED_prep.jpg?1426742267) ## LED Solder the negitive and positive pins of the LEDs. Use heat shrink to seal the wires.  ![](https://cdn-learn.adafruit.com/assets/assets/000/023/985/medium800/components_coin_copper.jpg?1426742328) ## Coin cell connection Peel and cut a small portion of the tape backing. Use the sticky side to connect to the positive and negitive sides of the battery.  Danger: ![](https://cdn-learn.adafruit.com/assets/assets/000/023/998/medium800/components_circuit-cross-section2.jpg?1426734884) ## Fit circuit into body Insert the tactile button into the cavity right behind the trigger. Carefully bend and tuck the wires into the shelled part of the body. Align the LED to the rear of the handle. Insert the coin cell battery into the half cylinder at the bottom. ![](https://cdn-learn.adafruit.com/assets/assets/000/023/997/medium800/components_btn-glued.jpg?1426734736) ## Secure tactile button Apply hot glue to the back of the tactile button to securly hold it in place. Danger: ![](https://cdn-learn.adafruit.com/assets/assets/000/024/019/medium800/components_glue-needle.jpg?1426827613) ## Assemble Needle Apply a small amount of E6000 to each half of the needle. Clamps or binders won't hold the two pieces in place, so instead hold them together for about 5 minutes until stick. Danger: ![](https://cdn-learn.adafruit.com/assets/assets/000/024/000/medium800/components_circuit-cross-sectionB.jpg?1426735144) ## Attach bottle and needle Add the needle to the front part of the body. Insert the LED into the bottle opening end. ![](https://cdn-learn.adafruit.com/assets/assets/000/023/999/medium800/components_close-body.jpg?1426735423) ## Align both pieces Fit the second half of the syringe body on top of the first half. Line up the tactile button cavities. Test alignment by checking the trigger to see if it actuates push button and LED. If it doesn't, double check your wiring and ensure the tactile button is secured in place.  Use #2-56 3/8 screws to attach the parts together. Make sure to tuck in any wires that might have slipped out of the sides while screwing the two pieces together. ![](https://cdn-learn.adafruit.com/assets/assets/000/024/001/medium800/components_nipple-attach.jpg?1426735292) ## NinjaFlex rubber nipple The rubber nipple part can be printed in TPE flexible material.   [Caramel](https://www.adafruit.com/product/2382) NinjaFlex matches pretty close to copperFill. To allow some of the light to pass through to the tip, we used translusent color, **water**. Use the change filament option to dual print two different colors! The nipple part grips the top of the bottle, just slip it right on! ![](https://cdn-learn.adafruit.com/assets/assets/000/023/991/medium800thumb/projects_components_syringe-hero.jpg?1448316832) Now you are ready to gather all that ADAM! If you ever need to transport this prop for your next con, you easily can disassemble and reassemble it - just be sure to bring your screw driver! The coin cell battery should last a while but it is rechargable.  ## Related Guides - [LEGO Head Lamp with Audio](https://learn.adafruit.com/lego-head-lamp-with-audio.md) - [CircuitPython Media Dial](https://learn.adafruit.com/media-dial.md) - [Four Channel Audio Passive Stereo Mixer](https://learn.adafruit.com/four-channel-audio-passive-stereo-mixer.md) - [Blahaj Alarm and Lamp](https://learn.adafruit.com/blahaj-alarm.md) - [Go Fishing with Rotary Encoders](https://learn.adafruit.com/gone-fishing-game.md) - [NAU7802 Pet Food Scale](https://learn.adafruit.com/nau7802-pet-food-scale.md) - [MUNNY Glowing Friend with Bluetooth Control!](https://learn.adafruit.com/munny-lamp.md) - [Milk Jug Glow Skull](https://learn.adafruit.com/milk-jug-glow-skull.md) - [Using micro:bit and CRICKIT with MicroPython](https://learn.adafruit.com/using-micro-bit-and-crickit-with-micropython.md) - [Fisher-Price USB Controller](https://learn.adafruit.com/fisher-price-usb-controller.md) - [Gemma M0 Sheikah Pendant](https://learn.adafruit.com/gemma-m0-sheikah-pendant.md) - [DIY Desktop Calculator with CircuitPython ](https://learn.adafruit.com/diy-rpn-desktop-calculator-with-circuitpython.md) - [Getting Started with Raspberry Pi Pico and CircuitPython](https://learn.adafruit.com/getting-started-with-raspberry-pi-pico-circuitpython.md) - [Circle of Fifths Euclidean Synth with synthio and CircuitPython](https://learn.adafruit.com/circle-of-fifths-euclidean-synth-with-synthio-and-circuitpython.md) - [PyPortal YouTube Views and Subscribers Display](https://learn.adafruit.com/pyportal-youtube-views-and-subscribers-display.md)