DC Toy Hobby Motor
These are standard '130 size' DC hobby motors. They come with a wider operating range than most toy motors: from 4.5 to 9VDC instead of 1.5-4.5V. This range makes them perfect for controlling with an Adafruit Motor Shield, or with an Arduino where you are more likely to have 5 or 9V...
$1.95 each
In Stock
Video of 24mm mini translucent clear LED arcade button flashing on and off.
A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they have LEDs built right in! That's right, you'll be button-mashing amidst a wash of beautiful light with these lil'...
$2.50 each
In Stock
angled shot of blue rectangular buckboost PCB.
Convert just about any battery pack to 5V with VERTER - our fresh new Buck-Boost power converter. VERTER can take battery voltages from 3-12VDC and output a nice 5V DC, which makes it a perfect universal power supply for your portable project! Where Verter really shines is when you have a...
$9.95 each
In Stock
Angled shot of  9V battery holder clip with 5.5mm/2.1mm plug.
I found these high-quality battery clips. They're molded plastic so they won't tear like cheap clips, and they cover the battery terminals to prevent shorts.Comes with a 5.5mm/2.1mm center-positive barrel connector, assembled!Battery not included.
$2.95 each
In Stock
Four radial ball bearings
Rollin' rollin' rollin', you can now roll around smooth as silk with these radial bearings. Often referred to as "skate bearings" They're good for supporting a rotating rod or as a wheel hub. However, these are higher quality, meant for continuous use so they'll...
Out of Stock
Angle Shot of PKcell 9V battery.
Battery power for your portable project! These batteries are high quality at a good price and work fantastic with any of the kits or projects in the shop that use 9V.These batteries are Alkaline (MnO2) chemistry, with a voltage range of 9.6V (fresh) to 4.8V (dead). The mAh capacity...
$1.50 each
In Stock
Red polished hand turning an Assembled snow globe kit with glowing electronics and friendly robot inside upside down and placing it back down.
Not merely a snow globe, but a show globe! This custom container is durable, clear and round, with a large flat screw-on top and a press-fit rubber stopper. The stopper makes a nice seal, and is also hollow which means you can put (you guessed it...) electronics inside! This...
$4.95 each
In Stock
Panel Mount 1/8 inch / 3.5mm TRS Audio Jack Connector
What is this TRS bit? Turtle Rock Studios? Transmission Raman Spectroscopy? Not quite, more...
$0.75 each
In Stock
Black stranded-core wire on a reel.
Silicone-sheathing wire is super-flexible and soft, and its also strong! Able to handle up to 200°C and up to 600V, it will do when PVC covered wire wimps out. We like this wire for being extremely supple and flexible, so it is great for wearables or projects where the wire-harness has to...
$4.95 each
In Stock
Solder Spool - 1/4 lb SAC305 RoHS lead-free / 0.031" rosin-core .
If you want to make a kit you'll need some solder. This 1/4 lb (about 110 gram) spool is just the right amount, not too much (like 1 lb spools) and not too little (like those little 'pocket clip' vials). This spool of solder is 0.031" in diameter, with the 'industry...
$29.95 each
In Stock
Array of many colorful heatshrink tubes.
Heat shrink is the duct tape of electronics which I guess makes this heat shrink the colorful and exciting duct tape they sell at craft stores.  This heat shrink comes in six different colors - red, blue, green, yellow, white and the traditional black.Each pack contains ten...
Out of Stock
Stainless steel double-ended prying tool
Is there something missing from your tool kit or workstation? Are you having trouble figuring out which elusive tool it is that you're lacking? Perhaps it's a spudger! "A what?" A s-p-u-d-g-e-r! It's a prying tool that has a wide...
$5.50 each
In Stock
Red and black multi-size wire stripplers, closed
These are the finest wire strippers we have used, and if you have to do a lot of wiring, you will agree! They have soft rounded grips - very comfortable to use, and precision ground notches that do a perfect job every time. No more yanking or twisting to strip wires cleanly and quickly.
$17.50 each
In Stock
Red and black diagonal flush cutters
These are the best diagonal cutters, large super-comfortable grip to use and have strong nippers for perfect trimming of wires and leads. I've used my pair every day for years.
$7.25 each
In Stock
Adjustable 30W 110V soldering iron with US 3-prong power cord
This 'pen-style' soldering iron is just about the best entry-level tool I've seen. It's not as powerful as a Weller WES51 but it is self-contained and easy to use. With proper care, it will last for many years. Turn it off when not in use, clean the plated tip with a...
No Longer Stocked
Smallish table-vise with adjustable jaws and universal joint
The best mini-vise for working on smaller PCBs (2.875" or less in one dimension)! The jaws are strong plastic that wont damage the PCB and doesn't mind if you hit it with the soldering iron by accident. Made in the USA.The easy-to-use single knob controls head movement...
No Longer Stocked
Third Hand Magnifier with two alligator grabbers and Magnifying Glass
The classic 'third hand tool,' as seen on every desk! We have one next to our Panavise jr, they complement each other well. This tool is good for holding small PCBs and wires for tinning or soldering to parts. Every...
$6.95 each
In Stock
Glamor shot of Ultimaker 2+ 3D Printer
The Ultimaker 2+ is one of our favorite 3D printers on the market. It's a well-built open-source compact machine with an excellent UX. Every inch of the Ultimaker 2+ is designed to create the most effortless and reliable 3D printing experience ever! 
No Longer Stocked