Overview
This guide provides further information about the various "arcade" style buttons in the Adafruit shop. These Arcade Buttons come in various shapes and sizes. Here's a link to the whole product category in the shop:
These buttons are not complex. However, they still garner a fair number of question in the forums. These typically are asking for additional information as people consider the buttons for their projects. What are the pin connections? How do you connect to the pins? What size hole to drill? Is part X removable? etc.
This guide is here to attempt to answer those questions. It's also set to free play, so no quarters needed. Read on...
The Buttons
This guide does not cover all "buttons" in the Adafruit shop. Just the "arcade" style ones which all have a common hardware back end. The big chonky thread post on the back is one feature to look for. Some specific examples below:
Button Size
For general size and dimensions, check each button's product page. Down near the bottom should be a link or other image that provides sizing information. For example, here's the 30mm Round button:
The microswitch itself seems to be common to all the buttons.
Page last edited May 28, 2025
Connections
The basic connections are shown below. The button switch and LED are completely separate. So there are two connections for the switch and two connections for the LED.
- The switch is non-latching, normally open.
- The LED includes a current limiting resistor allowing up to 12V power.
These style connectors have been around forever and go by various names: "spade connector", "flat blade connector", etc. Soldering to them is totally fine. There are also pre-crimped mating connector wires available (see cables below).
For some reason, the switch and LED connectors are two different sizes.
LED Polarity
The polarity of the two connections for the LED can vary. There are no LED polarity markings. It will depend on how the LED assembly itself is inserted into the button assembly, which can go either way. The easiest way to deal with this is to try powering one way. If the LED does not light up, then reverse the connections.
It's also possible to look down into the LED assembly and note the flat side cut on the LED itself. That will indicate the cathode (-) side.
If you want to actually verify the polarity, the LED assembly can be removed and inspected directly. See the Disassembly section of this guide for further information.
Quick Connect Cables
Ready made quick connect cables are available in various sizes. The non-button end is terminated in a 2 pin JST XH connector. The JST XH mates directly with the Adafruit LED Arcade Button 1x4 STEMMA QT Breakout. If the JST XH connector is not needed, it can be cut off.
The size of the connectors for the switch and LED can unfortunately be different. Therefore multiple sizes may be needed. Check the product page for details.
Page last edited May 28, 2025
Disassembly
Removing the switch/LED assembly is needed for installing the button (see Usage section). Other than that, there is generally no need to disassemble the button any further for basic usage. However, we detail disassembly here for those wanting to potentially modify the button in some way.
Re-assembly is generally just the reverse of the disassembly shown below.
Removing Button/LED Insert
This is actually a necessary step for final installation. See the Usage section for more details.
The switch and LED are both held together in a single assembly that fits inside the button screw post. It is held in with a twist lock.
Putting the assembly back in just the opposite. Look inside for the two black tabs that the assembly must initially be aligned with. Then push the assembly in and twist to lock it back in place.
Removing LED
The LED and current limiting resistor are held together in a little assembly that can be removed from the button/LED. The LED and resistor can also be completely removed from this assembly.
By unwrapping the wire leads on the posts, the LED itself can be removed. Along with the current limiting resistor.
The resistor appears to be 680 Ohms.
The LED sub-assembly is held in place by a friction fit without any indexing. The LED polarity on the external pins will be a result of the orientation of this LED sub-assembly.
Removing the Microswitch
The switch itself is held in the button/LED assembly via two posts. Removing this is difficult and not recommended due to amount of prying needed.
The posts are long enough and the two tabs are stiff enough that this takes a fair amount of effort. The only reason to do this would be to replace the microswitch for some reason.
Removing Button Cap Assembly
The button assembly can be removed as well. Be careful not to lose the spring.
- Squeeze in on the two white tabs holding the button into the black plastic post.
- Once tabs are pushed in, press down to start sliding the assembly through the black plastic post.
Removing Button Top Cap
The top plastic part of the button is press fit onto the button cap assembly. With some careful spudging, it can be removed.
Carefully pry up to get started. Once a little bit gets lifted, the rest will come out easy.
The smaller the button size, the trickier this removal is.
Page last edited May 28, 2025
Usage
Installing the button is simple. The only caveat is that the LED/switch assembly needs to be initially removed and installed once the button is mounted.
The electrical connections are also simple. The switch is just a switch and the LED is just an LED.
Installation
These arcade buttons seem to have standardized on a metric M24 thread. A through hole (clearance hole) size of 26mm or 1" diameter will work. Once the hole is cut, assembling the button is as follows:
Now the electrical connections can be made.
Electrical Connections
The switch used by the button is non-latching, normally open. Normally open means the two switch pins are open (not connected) when the button is not pressed. When the button is pressed, the switch pins are closed (connected). Non-latching means the switch closure only occurs while the button is pressed down.
Wiring the switch/button follows the same general guidance as any switch. See the following guide for more info:
The LED is a basic 5mm LED with an inline current limiting resistor. The resistor is sized to allow for powering up to 12V which draws about 20mA. Controlling the LED in the button follows the same general guidance as any LED. See the following guide for more info:
Page last edited May 28, 2025