# Adafruit TRRS Trinkey
## Overview
It's half USB Key, half TRRS breakout_..._ it's the **Adafruit TRRS Trinkey** specifically designed for Assistive Technology hackers and creators as a simple and low cost, but also flexible and extendable AT device.
Many AT interface devices use 3.5mm audio jacks to create switches or variable inputs - often mono TS or stereo TRS plugs. On the TRRS Trinkey, we connect all 6 pins of a 'switched' TRRS jack - tip, ring 1, ring 2, sleeve and the tip switch plus ring 1 switch - to 6 GPIO pins on the microcontroller. That means we can not only detect when plugs are inserted but can change which pins are input, ground or even 3V power. With the use of a stereo/mic splitter, we can have up to 3 simple switches, or two analog potentiometers, or one of each! We particularly like this jack because it has two through-hole contacts near the opening for a good mechanical connection.
The PCB is designed to plug into any USB A port on a computer or laptop. There's an ATSAMD21 microcontroller on board with just enough circuitry to keep it happy. One pin of the microcontroller connects to a NeoPixel LED. A reset button lets you enter bootloader mode if necessary. The microcontroller can be programmed easily thanks to the UF2 bootloader and CircuitPython: simply drag-n-drop new code on.
The SAMD21 can run CircuitPython or Arduino nicely. Over the USB connection, you can have serial, MIDI, or HID keyboard/mouse connectivity. Because its a fully programmable chip, it's possible to customize the keyboard or mouse commands executed on each button, or even set up chording patterns.
**Features:**
- **ATSAMD21E18 32-bit Cortex M0+** - 48 MHz 32-bit processor with 256KB Flash and 32 KB RAM
- **Native USB supported by every OS** - can be used in Arduino or CircuitPython as a USB serial console, MIDI, Keyboard/Mouse HID, and even a little disk drive for storing Python scripts. Can act like a keyboard to phones or tablets with a USB adapter cable.
- Can be used with **Arduino IDE** or **CircuitPython**
- **TRRS Jack** with two switches on tip and ring 1. All 6 contacts connect to analog-input capable GPIO pins
- One **RGB NeoPixel LED**
- **STEMMA QT port with JST SH 4-pin compatible connector** - can be used to add I2C devices, or two more inputs. Note CircuitPython may not have enough memory for large chip drivers.
- **Reset switch** to start your project code over or enter bootloader mode
- **Open Source Hardware** so you have full control over your assistive tech!
# Adafruit TRRS Trinkey
## Pinouts
The PrettyPins PDF is available [here](https://github.com/adafruit/Adafruit-TRRS-Trinkey-PCB/blob/main/Adafruit%20TRRS%20Trinkey%20PrettyPins.pdf).
## ATSAMD21 Microcontroller
The center of the board is home to the **ATSAMD21E18 microcontroller**. It is a 32-bit Cortex M0+ processor at 48 MHz with 256KB Flash and 32 KB RAM. The SAMD21 has native USB supported by every OS. It can be used in Arduino or CircuitPython as USB serial console, MIDI, Keyboard/Mouse HID, even a little disk drive for storing Python scripts.
## USB Connector
On one end of the TRRS Trinkey is the **USB connector**. Plug it into any USB A port on your laptop or computer, NeoPixel-and-TRRS-jack-side-up.
## TRRS Jack
On the end of the board is the **TRRS jack**. It is a 'switched' 3.5mm audio jack that is connected to 6 GPIO pins. That means we can not only detect when plugs are inserted but can change which pins are input, ground or even 3V power. With the use of a stereo/mic splitter, we can have up to 3 simple switches, or two analog potentiometers, or one of each.
- **Tip** - `board.TIP` in CircuitPython or `PIN_TIP` or `0` in Arduino (the tip or **T** in **T** RRS).
- **Tip Switch** - This is the tip switch pin. When the plug is _not_ inserted, this pin is connected to the tip contact. When the plug _is_ inserted, this pin will float. It is `board.TIP_SWITCH` in CircuitPython and `PIN_TIP_SWITCH` or `1` in Arduino.
- **Ring 1** - `board.RING_1` in CircuitPython or `PIN_RING1` or `2` in Arduino (the first **R** in T **R** RS).
- **Ring 1 Switch** - This is the ring 1 switch pin. When the plug is _not_ inserted, this pin is connected to the right contact. When the plug _is_ inserted, this pin will float. It is `board.RING_1_SWITCH` in CircuitPython and `PIN_RING_SWITCH` or `3` in Arduino.
- **Ring 2** - `board.RING_2` in CircuitPython or `PIN_RING2` or `4` in Arduino (the second **R** in TR **R** S).
- **Sleeve** - `board.SLEEVE` in CircuitPython or `PIN_SLEEVE` or `5` in Arduino (the **S** in TRR **S**.
## STEMMA QT Connector
On the end of the board opposite the USB connector is the **STEMMA QT connector**. This allows you to use a STEMMA QT cable to connect up any STEMMA QT-capable sensor or breakout to quickly get started with no soldering necessary.
In CircuitPython, you can use the STEMMA connector with `board.SCL` and `board.SDA`, or `board.STEMMA_I2C()`. In Arduino, you can use pins `9` and `8` or `&Wire`.
## NeoPixel
Towards the end of the board opposite the USB connector is one **RGB NeoPixel LED**. It is labeled **Neo** on the board silk. This LED is controllable in CircuitPython using `board.NeoPixel` and Arduino using `PIN_NEOPIXEL` or `1`.
## Reset Button
Towards the center of the board, above the microcontroller, is the **reset button**.
Tap once to reset the board. Tap twice to enter the bootloader (needed for installing CircuitPython).
## Debug
On the back of the board are three pads that can be used for JTAG debugging. They are labeled, left to right:
- **SWD** - The data pin.
- **SWC** - The clock pin
- **Rst** - The reset pin.
# Adafruit TRRS Trinkey
## Install CircuitPython
[CircuitPython](https://github.com/adafruit/circuitpython) is a derivative of [MicroPython](https://micropython.org) designed to simplify experimentation and education on low-cost microcontrollers. It makes it easier than ever to get prototyping by requiring no upfront desktop software downloads. Simply copy and edit files on the **CIRCUITPY** drive to iterate.
## CircuitPython Quickstart
Follow this step-by-step to quickly get CircuitPython running on your board.
[Download the latest version of CircuitPython for this board via circuitpython.org](https://circuitpython.org/board/adafruit_trrs_trinkey_m0/)
**Click the link above to download the latest CircuitPython UF2 file.**
Save it wherever is convenient for you.
Plug your board into your computer, using a known-good data-sync cable, directly, or via an adapter if needed.
Double-click the **reset** button (highlighted in red above), and you will see the **RGB status LED(s)** turn green (highlighted in green above). If you see red, try another port, or if you're using an adapter or hub, try without the hub, or different adapter or hub.
If double-clicking doesn't work the first time, try again. Sometimes it can take a few tries to get the rhythm right!
A lot of people end up using charge-only USB cables and it is very frustrating! **Make sure you have a USB cable you know is good for data sync.**
You will see a new disk drive appear called **TRINKEYBOOT**.
Drag the **adafruit-circuitpython-etc.uf2** file to **TRINKEYBOOT**.
The **BOOT** drive will disappear and a new disk drive called **CIRCUITPY** will appear.
That's it!
# Adafruit TRRS Trinkey
## Installing the Mu Editor
Mu is a simple code editor that works with the Adafruit CircuitPython boards. It's written in Python and works on Windows, MacOS, Linux and Raspberry Pi. The serial console is built right in so you get immediate feedback from your board's serial output!
Info: Mu is our recommended editor - please use it (unless you are an experienced coder with a favorite editor already!). While it has been announced end of life in 2026, it still works fine.
You are free to use whatever text editor you wish along with a terminal program to connect to the CircuitPython REPL. Thonny is one such editor.
## Download and Install Mu
Download Mu from [https://codewith.mu](https://codewith.mu/).
Click the **Download** link for downloads and installation instructions.
Click **Start Here ** to find a wealth of other information, including extensive tutorials and and how-to's.
Warning:
## Starting Up Mu
The first time you start Mu, you will be prompted to select your 'mode' - you can always change your mind later. For now please select **CircuitPython**!
The current mode is displayed in the lower right corner of the window, next to the "gear" icon. If the mode says "Microbit" or something else, click the **Mode** button in the upper left, and then choose "CircuitPython" in the dialog box that appears.
Mu attempts to auto-detect your board on startup, so if you do not have a CircuitPython board plugged in with a **CIRCUITPY** drive available, Mu will inform you where it will store any code you save until you plug in a board.
To avoid this warning, plug in a board and ensure that the **CIRCUITPY** drive is mounted before starting Mu.
## Using Mu
You can now explore Mu! The three main sections of the window are labeled below; the button bar, the text editor, and the serial console / REPL.
Now you're ready to code! Let's keep going...
# Adafruit TRRS Trinkey
## Creating and Editing Code
One of the best things about CircuitPython is how simple it is to get code up and running. This section covers how to create and edit your first CircuitPython program.
To create and edit code, all you'll need is an editor. There are many options. **Adafruit strongly recommends using Mu! It's designed for CircuitPython, and it's really simple and easy to use, with a built in serial console!**
If you don't or can't use Mu, there are a number of other editors that work quite well. The [Recommended Editors page](https://learn.adafruit.com/welcome-to-circuitpython/recommended-editors) has more details. Otherwise, make sure you do "Eject" or "Safe Remove" on Windows or "sync" on Linux after writing a file if you aren't using Mu. (This was formerly not a problem on macOS, but see the warning below.)
Warning: macOS Sonoma 14.1 introduced a bug that delays writes to small drives such as CIRCUITPY drives. This caused errors when saving files to CIRCUITPY. There is a [workaround](https://learn.adafruit.com/welcome-to-circuitpython/troubleshooting#macos-sonoma-14-dot-x-disk-errors-writing-to-circuitpy-3160304). The bug was fixed in Sonoma 14.4, but at the cost of greatly slowed writes to drives 1GB or smaller.
## Creating Code
Installing CircuitPython generates a **code.py** file on your **CIRCUITPY** drive. To begin your own program, open your editor, and load the **code.py** file from the **CIRCUITPY** drive.
If you are using Mu, click the **Load** button in the button bar, navigate to the **CIRCUITPY** drive, and choose **code.py**.
Copy and paste the following code into your editor:
```python
import board
import digitalio
import time
led = digitalio.DigitalInOut(board.LED)
led.direction = digitalio.Direction.OUTPUT
while True:
led.value = True
time.sleep(0.5)
led.value = False
time.sleep(0.5)
```
Danger: The KB2040, QT Py , Qualia, and the Trinkeys do not have a built-in little red LED! There is an addressable RGB NeoPixel LED. The above example will NOT work on the KB2040, QT Py, Qualia, or the Trinkeys!
If you're using a KB2040, QT Py, Quaila, or a Trinkey, or any other board without a single-color LED that can blink, please download the [NeoPixel blink example](https://github.com/adafruit/Adafruit_Learning_System_Guides/blob/master/Welcome_to_CircuitPython/code.py).
Info:
It will look like this. Note that under the `while True:` line, the next four lines begin with four spaces to indent them, and they're indented exactly the same amount. All the lines before that have no spaces before the text.
Save the **code.py** file on your **CIRCUITPY** drive.
The little LED should now be blinking. Once per half-second.
Congratulations, you've just run your first CircuitPython program!
Info: On most boards you'll find a tiny red LED. On the ItsyBitsy nRF52840, you'll find a tiny blue LED. On QT Py M0, QT Py RP2040, Qualia, and the Trinkey series, you will find only an RGB NeoPixel LED.
## Editing Code
To edit code, open the **code.py** file on your **CIRCUITPY** drive into your editor.
Make the desired changes to your code. Save the file. That's it!
### Your code changes are run as soon as the file is done saving.
There's one warning before you continue...
Danger:
The CircuitPython code on your board detects when the files are changed or written and will automatically re-start your code. This makes coding very fast because you save, and it re-runs. If you unplug or reset the board before your computer finishes writing the file to your board, you can corrupt the drive. If this happens, you may lose the code you've written, so it's important to backup your code to your computer regularly.
There are a couple of ways to avoid filesystem corruption.
### **1. Use an editor that writes out the file completely when you save it.**
Check out the [Recommended Editors page](https://learn.adafruit.com/welcome-to-circuitpython/recommended-editors) for details on different editing options.
Info:
### **2. Eject or Sync the Drive After Writing**
If you are using one of our not-recommended-editors, not all is lost! You can still make it work.
On Windows, you can Eject or Safe Remove the **CIRCUITPY** drive. It won't actually eject, but it will force the operating system to save your file to disk. On Linux, use the **sync** command in a terminal to force the write to disk.
You also need to do this if you use Windows Explorer or a Linux graphical file manager to drag a file onto **CIRCUITPY**.
###
Don't worry! Corrupting the drive isn't the end of the world (or your board!). If this happens, follow the steps found on the [Troubleshooting](https://learn.adafruit.com/welcome-to-circuitpython/troubleshooting) page of every board guide to get your board up and running again.
Info: If you are having trouble saving code on Windows 10, try including this code snippet at the top of code.py:
```python
import supervisor
supervisor.runtime.autoreload = False
```
## Back to Editing Code...
Now! Let's try editing the program you added to your board. Open your **code.py** file into your editor. You'll make a simple change. Change the first `0.5` to `0.1`. The code should look like this:
```python
import board
import digitalio
import time
led = digitalio.DigitalInOut(board.LED)
led.direction = digitalio.Direction.OUTPUT
while True:
led.value = True
time.sleep(0.1)
led.value = False
time.sleep(0.5)
```
Leave the rest of the code as-is. Save your file. See what happens to the LED on your board? Something changed! Do you know why?
You don't have to stop there! Let's keep going. Change the second `0.5` to `0.1` so it looks like this:
```
while True:
led.value = True
time.sleep(0.1)
led.value = False
time.sleep(0.1)
```
Now it blinks really fast! You decreased the both time that the code leaves the LED on and off!
Now try increasing both of the `0.1` to `1`. Your LED will blink much more slowly because you've increased the amount of time that the LED is turned on and off.
Well done! You're doing great! You're ready to start into new examples and edit them to see what happens! These were simple changes, but major changes are done using the same process. Make your desired change, save it, and get the results. That's really all there is to it!
# Naming Your Program File
CircuitPython looks for a code file on the board to run. There are four options: **code.txt** , **code.py** , **main.txt** and **main.py**. CircuitPython looks for those files, in that order, and then runs the first one it finds. While **code.py** is the recommended name for your code file, it is important to know that the other options exist. If your program doesn't seem to be updating as you work, make sure you haven't created another code file that's being read instead of the one you're working on.
# Adafruit TRRS Trinkey
## Connecting to the Serial Console
One of the staples of CircuitPython (and programming in general!) is something called a "print statement". This is a line you include in your code that causes your code to output text. A print statement in CircuitPython (and Python) looks like this:
`print("Hello, world!")`
This line in your code.py would result in:
`Hello, world!`
However, these print statements need somewhere to display. That's where the serial console comes in!
The serial console receives output from your CircuitPython board sent over USB and displays it so you can see it. This is necessary when you've included a print statement in your code and you'd like to see what you printed. It is also helpful for troubleshooting errors, because your board will send errors and the serial console will display those too.
The serial console requires an editor that has a built in terminal, or a separate terminal program. A terminal is a program that gives you a text-based interface to perform various tasks.
# Are you using Mu?
If so, good news! The serial console **is built into Mu** and will **autodetect your board** making using the serial console _really really easy_.
First, make sure your CircuitPython board is plugged in.
If you open Mu without a board plugged in, you may encounter the error seen here, letting you know no CircuitPython board was found and indicating where your code will be stored until you plug in a board.
[If you are using Windows 7, make sure you installed the drivers](https://learn.adafruit.com/welcome-to-circuitpython/windows-7-and-8-1-drivers).
Once you've opened Mu with your board plugged in, look for the **Serial** button in the button bar and click it.
The Mu window will split in two, horizontally, and display the serial console at the bottom.
Info:
## Serial Console Issues or Delays on Linux
If you're on Linux, and are seeing multi-second delays connecting to the serial console, or are seeing "AT" and other gibberish when you connect, then the `modemmanager` service might be interfering. Just remove it; it doesn't have much use unless you're still using dial-up modems.
To remove `modemmanager`, type the following command at a shell:
```terminal
sudo apt purge modemmanager
```
## Setting Permissions on Linux
On Linux, if you see an error box something like the one below when you press the **Serial** button, you need to add yourself to a user group to have permission to connect to the serial console.
On Ubuntu and Debian, add yourself to the **dialout** group by doing:
```terminal
sudo adduser $USER dialout
```
After running the command above, reboot your machine to gain access to the group. On other Linux distributions, the group you need may be different. See the [Advanced Serial Console on Linux](https://learn.adafruit.com/welcome-to-circuitpython/advanced-serial-console-on-linux) for details on how to add yourself to the right group.
# Using Something Else?
If you're not using Mu to edit, or if for some reason you are not a fan of its built in serial console, you can run the serial console from a separate program.
Windows requires you to download a terminal program. [Check out the Advanced Serial Console on Windows page for more details.](../../../../welcome-to-circuitpython/advanced-serial-console-on-windows)
MacOS has serial connection programs you can run in Terminal. [Check the Advanced Serial Console on Mac page for more details.](../../../../welcome-to-circuitpython/advanced-serial-console-on-mac-and-linux)
Linux has multiple terminal programs included options are available for download. [Check the Advanced Serial Console on Linux page for more details.](https://learn.adafruit.com/welcome-to-circuitpython/advanced-serial-console-on-linux)
Once connected, you'll see something like the following.
# Adafruit TRRS Trinkey
## Interacting with the Serial Console
Once you've successfully connected to the serial console, it's time to start using it.
The code you wrote earlier has no output to the serial console. So, you're going to edit it to create some output.
Open your code.py file into your editor, and include a `print` statement. You can print anything you like! Just include your phrase between the quotation marks inside the parentheses. For example:
```python
import board
import digitalio
import time
led = digitalio.DigitalInOut(board.LED)
led.direction = digitalio.Direction.OUTPUT
while True:
print("Hello, CircuitPython!")
led.value = True
time.sleep(1)
led.value = False
time.sleep(1)
```
Save your file.
Now, let's go take a look at the window with our connection to the serial console.
Excellent! Our print statement is showing up in our console! Try changing the printed text to something else.
```python
import board
import digitalio
import time
led = digitalio.DigitalInOut(board.LED)
led.direction = digitalio.Direction.OUTPUT
while True:
print("Hello back to you!")
led.value = True
time.sleep(1)
led.value = False
time.sleep(1)
```
Keep your serial console window where you can see it. Save your file. You'll see what the serial console displays when the board reboots. Then you'll see your new change!
The `Traceback (most recent call last):` is telling you the last thing your board was doing before you saved your file. This is normal behavior and will happen every time the board resets. This is really handy for troubleshooting. Let's introduce an error so you can see how it is used.
Delete the `e` at the end of `True` from the line `led.value = True` so that it says `led.value = Tru`
```python
import board
import digitalio
import time
led = digitalio.DigitalInOut(board.LED)
led.direction = digitalio.Direction.OUTPUT
while True:
print("Hello back to you!")
led.value = Tru
time.sleep(1)
led.value = False
time.sleep(1)
```
Save your file. You will notice that your red LED will stop blinking, and you may have a colored status LED blinking at you. This is because the code is no longer correct and can no longer run properly. You need to fix it!
Usually when you run into errors, it's not because you introduced them on purpose. You may have 200 lines of code, and have no idea where your error could be hiding. This is where the serial console can help. Let's take a look!
The `Traceback (most recent call last):` is telling you that the last thing it was able to run was `line 10` in your code. The next line is your error: `NameError: name 'Tru' is not defined`. This error might not mean a lot to you, but combined with knowing the issue is on line 10, it gives you a great place to start!
Go back to your code, and take a look at line 10. Obviously, you know what the problem is already. But if you didn't, you'd want to look at line 10 and see if you could figure it out. If you're still unsure, try googling the error to get some help. In this case, you know what to look for. You spelled True wrong. Fix the typo and save your file.
Nice job fixing the error! Your serial console is streaming and your red LED Is blinking again.
The serial console will display any output generated by your code. Some sensors, such as a humidity sensor or a thermistor, receive data and you can use print statements to display that information. You can also use print statements for troubleshooting, which is called "print debugging". Essentially, if your code isn't working, and you want to know where it's failing, you can put print statements in various places to see where it stops printing.
The serial console has many uses, and is an amazing tool overall for learning and programming!
# Adafruit TRRS Trinkey
## The REPL
The other feature of the serial connection is the **R** ead- **E** valuate **-**** P **rint-** L**oop, or REPL. The REPL allows you to enter individual lines of code and have them run immediately. It's really handy if you're running into trouble with a particular program and can't figure out why. It's interactive so it's great for testing new ideas.
## Entering the REPL
To use the REPL, you first need to be connected to the serial console. Once that connection has been established, you'll want to press **CTRL+C**.
If there is code running, in this case code measuring distance, it will stop and you'll see `Press any key to enter the REPL. Use CTRL-D to reload.` Follow those instructions, and press any key on your keyboard.
The `Traceback (most recent call last):` is telling you the last thing your board was doing before you pressed Ctrl + C and interrupted it. The `KeyboardInterrupt` is you pressing CTRL+C. This information can be handy when troubleshooting, but for now, don't worry about it. Just note that it is expected behavior.
If your **code.py** file is empty or does not contain a loop, it will show an empty output and `Code done running.`. There is no information about what your board was doing before you interrupted it because there is no code running.
If you have no **code.py** on your **CIRCUITPY** drive, you will enter the REPL immediately after pressing CTRL+C. Again, there is no information about what your board was doing before you interrupted it because there is no code running.
Regardless, once you press a key you'll see a `>>>` prompt welcoming you to the REPL!
If you have trouble getting to the `>>>` prompt, try pressing Ctrl + C a few more times.
The first thing you get from the REPL is information about your board.
This line tells you the version of CircuitPython you're using and when it was released. Next, it gives you the type of board you're using and the type of microcontroller the board uses. Each part of this may be different for your board depending on the versions you're working with.
This is followed by the CircuitPython prompt.
## Interacting with the REPL
From this prompt you can run all sorts of commands and code. The first thing you'll do is run `help()`. This will tell you where to start exploring the REPL. To run code in the REPL, type it in next to the REPL prompt.
Type `help()` next to the prompt in the REPL.
Then press enter. You should then see a message.
First part of the message is another reference to the version of CircuitPython you're using. Second, a URL for the CircuitPython related project guides. Then... wait. What's this? To list built-in modules type `help("modules").` Remember the modules you learned about while going through creating code? That's exactly what this is talking about! This is a perfect place to start. Let's take a look!
Type `help("modules")` into the REPL next to the prompt, and press enter.
This is a list of all the core modules built into CircuitPython, including `board`. Remember, `board` contains all of the pins on the board that you can use in your code. From the REPL, you are able to see that list!
Type `import board` into the REPL and press enter. It'll go to a new prompt. It might look like nothing happened, but that's not the case! If you recall, the `import` statement simply tells the code to expect to do something with that module. In this case, it's telling the REPL that you plan to do something with that module.
Next, type `dir(board)` into the REPL and press enter.
This is a list of all of the pins on your board that are available for you to use in your code. Each board's list will differ slightly depending on the number of pins available. Do you see `LED`? That's the pin you used to blink the red LED!
The REPL can also be used to run code. Be aware that **any code you enter into the REPL isn't saved** anywhere. If you're testing something new that you'd like to keep, make sure you have it saved somewhere on your computer as well!
Every programmer in every programming language starts with a piece of code that says, "Hello, World." You're going to say hello to something else. Type into the REPL:
`print("Hello, CircuitPython!")`
Then press enter.
That's all there is to running code in the REPL! Nice job!
You can write single lines of code that run stand-alone. You can also write entire programs into the REPL to test them. Remember that nothing typed into the REPL is saved.
There's a lot the REPL can do for you. It's great for testing new ideas if you want to see if a few new lines of code will work. It's fantastic for troubleshooting code by entering it one line at a time and finding out where it fails. It lets you see what modules are available and explore those modules.
Try typing more into the REPL to see what happens!
Warning:
# Returning to the Serial Console
When you're ready to leave the REPL and return to the serial console, simply press **CTRL+D**. This will reload your board and reenter the serial console. You will restart the program you had running before entering the REPL. In the console window, you'll see any output from the program you had running. And if your program was affecting anything visual on the board, you'll see that start up again as well.
You can return to the REPL at any time!
# Adafruit TRRS Trinkey
## CircuitPython Libraries
Danger:
Each CircuitPython program you run needs to have a lot of information to work. The reason CircuitPython is so simple to use is that most of that information is stored in other files and works in the background. These files are called _libraries_. Some of them are built into CircuitPython. Others are stored on your **CIRCUITPY** drive in a folder called **lib**. Part of what makes CircuitPython so great is its ability to store code separately from the firmware itself. Storing code separately from the firmware makes it easier to update both the code you write and the libraries you depend.
Your board may ship with a **lib** folder already, it's in the base directory of the drive. If not, simply create the folder yourself. When you first install CircuitPython, an empty **lib** directory will be created for you.
CircuitPython libraries work in the same way as regular Python modules so the [Python docs](https://docs.python.org/3/tutorial/modules.html) are an excellent reference for how it all should work. In Python terms, you can place our library files in the **lib** directory because it's part of the Python path by default.
One downside of this approach of separate libraries is that they are not built in. To use them, one needs to copy them to the **CIRCUITPY** drive before they can be used. Fortunately, there is a library bundle.
The bundle and the library releases on GitHub also feature optimized versions of the libraries with the **.mpy** file extension. These files take less space on the drive and have a smaller memory footprint as they are loaded.
Due to the regular updates and space constraints, Adafruit does not ship boards with the entire bundle. Therefore, you will need to load the libraries you need when you begin working with your board. You can find example code in the guides for your board that depends on external libraries.
Either way, as you start to explore CircuitPython, you'll want to know how to get libraries on board.
# The Adafruit Learn Guide Project Bundle
The quickest and easiest way to get going with a project from the Adafruit Learn System is by utilising the Project Bundle. Most guides now have a **Download Project Bundle** button available at the top of the full code example embed. This button downloads all the necessary files, including images, etc., to get the guide project up and running. Simply click, open the resulting zip, copy over the right files, and you're good to go!
The first step is to find the Download Project Bundle button in the guide you're working on.
Info:
Warning:
The Download Project Bundle button downloads a zip file. This zip contains a series of directories, nested within which is the **code.py** , any applicable assets like images or audio, and the **lib/** folder containing all the necessary libraries. The following zip was downloaded from the Piano in the Key of Lime guide.
Info:
When you open the zip, you'll find some nested directories. Navigate through them until you find what you need. You'll eventually find a directory for your CircuitPython version (in this case, 7.x). In the version directory, you'll find the file and directory you need: **code.py** and **lib/**. Once you find the content you need, you can copy it all over to your **CIRCUITPY** drive, replacing any files already on the drive with the files from the freshly downloaded zip.
Info:
Once you copy over all the relevant files, the project should begin running! If you find that the project is not running as expected, make sure you've copied ALL of the project files onto your microcontroller board.
That's all there is to using the Project Bundle!
# The Adafruit CircuitPython Library Bundle
Adafruit provides CircuitPython libraries for much of the hardware they provide, including sensors, breakouts and more. To eliminate the need for searching for each library individually, the libraries are available together in the Adafruit CircuitPython Library Bundle. The bundle contains all the files needed to use each library.
## Downloading the Adafruit CircuitPython Library Bundle
You can download the latest Adafruit CircuitPython Library Bundle release by clicking the button below. The libraries are being constantly updated and improved, so you'll always want to download the latest bundle.
**Match up the bundle version with the version of CircuitPython you are running.** For example, you would download the 6.x library bundle if you're running any version of CircuitPython 6, or the 7.x library bundle if you're running any version of CircuitPython 7, etc. If you mix libraries with major CircuitPython versions, you will get incompatible mpy errors due to changes in library interfaces possible during major version changes.
[Click to visit circuitpython.org for the latest Adafruit CircuitPython Library Bundle](https://circuitpython.org/libraries)
**Download the bundle version that matches your CircuitPython firmware version.** If you don't know the version, check the version info in **boot\_out.txt** file on the **CIRCUITPY** drive, or the initial prompt in the CircuitPython REPL. For example, if you're running v7.0.0, download the 7.x library bundle.
There's also a **py** bundle which contains the uncompressed python files, you probably _don't_ want that unless you are doing advanced work on libraries.
# The CircuitPython Community Library Bundle
The CircuitPython Community Library Bundle is made up of libraries written and provided by members of the CircuitPython community. These libraries are often written when community members encountered hardware not supported in the Adafruit Bundle, or to support a personal project. The authors all chose to submit these libraries to the Community Bundle make them available to the community.
**These libraries are maintained by their authors and are not supported by Adafruit.** As you would with any library, if you run into problems, feel free to file an issue on the GitHub repo for the library. Bear in mind, though, that most of these libraries are supported by a single person and you should be patient about receiving a response. Remember, these folks are not paid by Adafruit, and are volunteering their personal time when possible to provide support.
## Downloading the CircuitPython Community Library Bundle
You can download the latest CircuitPython Community Library Bundle release by clicking the button below. The libraries are being constantly updated and improved, so you'll always want to download the latest bundle.
[Click for the latest CircuitPython Community Library Bundle release](https://github.com/adafruit/CircuitPython_Community_Bundle/releases)
The link takes you to the latest release of the CircuitPython Community Library Bundle on GitHub. There are multiple versions of the bundle available. **Download the bundle version that matches your CircuitPython firmware version.** If you don't know the version, check the version info in **boot\_out.txt** file on the **CIRCUITPY** drive, or the initial prompt in the CircuitPython REPL. For example, if you're running v7.0.0, download the 7.x library bundle.
# Understanding the Bundle
After downloading the zip, extract its contents. This is usually done by double clicking on the zip. On Mac OSX, it places the file in the same directory as the zip.
Open the bundle folder. Inside you'll find two information files, and two folders. One folder is the lib bundle, and the other folder is the examples bundle.
Now open the lib folder. When you open the folder, you'll see a large number of **.**** mpy** files, and folders.
## Example Files
All example files from each library are now included in the bundles in an **examples** directory (as seen above), as well as an examples-only bundle. These are included for two main reasons:
- Allow for quick testing of devices.
- Provide an example base of code, that is easily built upon for individualized purposes.
## Copying Libraries to Your Board
First open the **lib** folder on your **CIRCUITPY** drive. Then, open the **lib** folder you extracted from the downloaded zip. Inside you'll find a number of folders and **.mpy** files. Find the library you'd like to use, and copy it to the **lib** folder on **CIRCUITPY**.
If the library is a directory with multiple **.mpy** files in it, be sure to **copy the entire folder to CIRCUITPY/lib**.
This also applies to example files. Open the **examples** folder you extracted from the downloaded zip, and copy the applicable file to your **CIRCUITPY** drive. Then, rename it to **code.py** to run it.
Info:
# Understanding Which Libraries to Install
You now know how to load libraries on to your CircuitPython-compatible microcontroller board. You may now be wondering, how do you know _which_ libraries you need to install? Unfortunately, it's not always straightforward. Fortunately, there is an obvious place to start, and a relatively simple way to figure out the rest. First up: the best place to start.
When you look at most CircuitPython examples, you'll see they begin with one or more `import` statements. These typically look like the following:
- `import library_or_module`
However, `import` statements can also sometimes look like the following:
- `from library_or_module import name`
- `from library_or_module.subpackage import name`
- `from library_or_module import name as local_name`
They can also have more complicated formats, such as including a `try` / `except` block, etc.
The important thing to know is that **an** `import` **statement will always include the name of the module or library that you're importing**.
Therefore, the best place to start is by reading through the `import` statements.
Here is an example import list for you to work with in this section. There is no setup or other code shown here, as the purpose of this section involves only the import list.
```python
import time
import board
import neopixel
import adafruit_lis3dh
import usb_hid
from adafruit_hid.consumer_control import ConsumerControl
from adafruit_hid.consumer_control_code import ConsumerControlCode
```
Keep in mind, not all imported items are libraries. Some of them are almost always built-in CircuitPython modules. How do you know the difference? Time to visit the REPL.
In the [Interacting with the REPL section](https://learn.adafruit.com/welcome-to-circuitpython/the-repl#interacting-with-the-repl-2977486-14) on [The REPL page](https://learn.adafruit.com/welcome-to-circuitpython/the-repl) in this guide, the `help("modules")` command is discussed. This command provides a list of all of the built-in modules available in CircuitPython for your board. So, if you connect to the serial console on your board, and enter the REPL, you can run `help("modules")` to see what modules are available for your board. Then, as you read through the `import` statements, you can, for the purposes of figuring out which libraries to load, ignore the statement that import modules.
The following is the list of modules built into CircuitPython for the Feather RP2040. Your list may look similar or be anything down to a significant subset of this list for smaller boards.
Now that you know what you're looking for, it's time to read through the import statements. The first two, `time` and `board`, are on the modules list above, so they're built-in.
The next one, `neopixel`, is not on the module list. That means it's your first library! So, you would head over to the bundle zip you downloaded, and search for **neopixel**. There is a **neopixel.mpy** file in the bundle zip. Copy it over to the **lib** folder on your **CIRCUITPY** drive. The following one, `adafruit_lis3dh`, is also not on the module list. Follow the same process for **adafruit\_lis3dh** , where you'll find **adafruit\_lis3dh.mpy** , and copy that over.
The fifth one is `usb_hid`, and it is in the modules list, so it is built in. Often all of the built-in modules come first in the import list, but sometimes they don't! Don't assume that everything after the first library is also a library, and verify each import with the modules list to be sure. Otherwise, you'll search the bundle and come up empty!
The final two imports are not as clear. Remember, when `import` statements are formatted like this, the first thing after the `from` is the library name. In this case, the library name is `adafruit_hid`. A search of the bundle will find an **adafruit\_hid _folder_**. When a library is a folder, you must copy the **entire folder and its contents _as it is in the bundle_** to the **lib** folder on your **CIRCUITPY** drive. In this case, you would copy the entire **adafruit\_hid** folder to your **CIRCUITPY/lib** folder.
Notice that there are _two_ imports that begin with `adafruit_hid`. Sometimes you will need to import more than one thing from the same library. Regardless of how many times you import the same library, you only need to load the library by copying over the **adafruit\_hid** folder _once_.
That is how you can use your example code to figure out what libraries to load on your CircuitPython-compatible board!
There are cases, however, where libraries require other libraries internally. The internally required library is called a _dependency_. In the event of library dependencies, the easiest way to figure out what other libraries are required is to connect to the serial console and follow along with the `ImportError` printed there. The following is a very simple example of an `ImportError`, but the concept is the same for any missing library.
# Example: `ImportError` Due to Missing Library
If you choose to load libraries as you need them, or you're starting fresh with an existing example, you may end up with code that tries to use a library you haven't yet loaded. This section will demonstrate what happens when you try to utilise a library that you don't have loaded on your board, and cover the steps required to resolve the issue.
This demonstration will only return an error if you do not have the required library loaded into the **lib** folder on your **CIRCUITPY** drive **.**
Let's use a modified version of the Blink example.
```auto
import board
import time
import simpleio
led = simpleio.DigitalOut(board.LED)
while True:
led.value = True
time.sleep(0.5)
led.value = False
time.sleep(0.5)
```
Save this file. Nothing happens to your board. Let's check the serial console to see what's going on.
You have an `ImportError`. It says there is `no module named 'simpleio'`. That's the one you just included in your code!
Click the link above to download the correct bundle. Extract the lib folder from the downloaded bundle file. Scroll down to find **simpleio.mpy**. This is the library file you're looking for! Follow the steps above to load an individual library file.
The LED starts blinking again! Let's check the serial console.
No errors! Excellent. You've successfully resolved an `ImportError`!
If you run into this error in the future, follow along with the steps above and choose the library that matches the one you're missing.
# Library Install on Non-Express Boards
If you have an M0 non-Express board such as Trinket M0, Gemma M0, QT Py M0, or one of the M0 Trinkeys, you'll want to follow the same steps in the example above to install libraries as you need them. Remember, you don't need to wait for an `ImportError` if you know what library you added to your code. Open the library bundle you downloaded, find the library you need, and drag it to the **lib** folder on your **CIRCUITPY** drive.
You can still end up running out of space on your M0 non-Express board even if you only load libraries as you need them. There are a number of steps you can use to try to resolve this issue. You'll find suggestions on the [Troubleshooting page](https://learn.adafruit.com/welcome-to-circuitpython/troubleshooting).
# Updating CircuitPython Libraries and Examples
Libraries and examples are updated from time to time, and it's important to update the files you have on your **CIRCUITPY** drive.
To update a single library or example, follow the same steps above. When you drag the library file to your lib folder, it will ask if you want to replace it. Say yes. That's it!
A new library bundle is released every time there's an update to a library. Updates include things like bug fixes and new features. It's important to check in every so often to see if the libraries you're using have been updated.
## CircUp CLI Tool
There is a command line interface (CLI) utility called [CircUp](https://learn.adafruit.com/keep-your-circuitpython-libraries-on-devices-up-to-date-with-circup) that can be used to easily install and update libraries on your device. Follow the directions on the [install page within the CircUp learn guide](https://learn.adafruit.com/keep-your-circuitpython-libraries-on-devices-up-to-date-with-circup/install-circup). Once you've got it installed you run the command `circup update` in a terminal to interactively update all libraries on the connected CircuitPython device. See the [usage page in the CircUp guide](https://learn.adafruit.com/keep-your-circuitpython-libraries-on-devices-up-to-date-with-circup/usage) for a full list of functionality
# Adafruit TRRS Trinkey
## Frequently Asked Questions
These are some of the common questions regarding CircuitPython and CircuitPython microcontrollers.
###
What are some common acronyms to know?
CP or CPy = [CircuitPython](https://circuitpython.org)
CPC = [Circuit Playground Classic](https://www.adafruit.com/product/3000) (does not run CircuitPython)
CPX = [Circuit Playground Express](https://www.adafruit.com/product/3333)
CPB = [Circuit Playground Bluefruit](https://www.adafruit.com/product/4333)
## Using Older Versions
Danger:
### I have to continue using CircuitPython 8.x or earlier. Where can I find compatible libraries?
**We are no longer building or supporting the CircuitPython 8.x or earlier library bundles. We highly encourage you to [update CircuitPython to the latest version](https://circuitpython.org/downloads) and use [the current version of the libraries](https://circuitpython.org/libraries).** However, if for some reason you cannot update, here are the last available library bundles for older versions:
- [2.x bundle](https://github.com/adafruit/Adafruit_CircuitPython_Bundle/releases/download/20190903/adafruit-circuitpython-bundle-2.x-mpy-20190903.zip)
- [3.x bundle](https://github.com/adafruit/Adafruit_CircuitPython_Bundle/releases/download/20190903/adafruit-circuitpython-bundle-3.x-mpy-20190903.zip)
- [4.x bundle](https://github.com/adafruit/Adafruit_CircuitPython_Bundle/releases/download/20200707/adafruit-circuitpython-bundle-4.x-mpy-20200707.zip)
- [5.x bundle](https://github.com/adafruit/Adafruit_CircuitPython_Bundle/releases/download/20210129/adafruit-circuitpython-bundle-5.x-mpy-20210129.zip)
- [6.x bundle](https://github.com/adafruit/Adafruit_CircuitPython_Bundle/releases/download/20211213/adafruit-circuitpython-bundle-6.x-mpy-20211213.zip)
- [7.x bundle](https://github.com/adafruit/Adafruit_CircuitPython_Bundle/releases/download/20231003/adafruit-circuitpython-bundle-7.x-mpy-20231003.zip)
- [8.x bundle](https://github.com/adafruit/Adafruit_CircuitPython_Bundle/releases/download/20250213/adafruit-circuitpython-bundle-8.x-mpy-20250213.zip)
## Python Arithmetic
###
Does CircuitPython support floating-point numbers?
All CircuitPython boards support floating point arithmetic, even if the microcontroller chip does not support floating point in hardware. Floating point numbers are stored in 30 bits, with an 8-bit exponent and a 22-bit mantissa. Note that this is two bits less than standard 32-bit single-precision floats. You will get about 5-1/2 digits of decimal precision.
(The **broadcom** port may provide 64-bit floats in some cases.)
###
Does CircuitPython support long integers, like regular Python?
Python long integers (integers of arbitrary size) are available on most builds, except those on boards with the smallest available firmware size. On these boards, integers are stored in 31 bits.
Boards without long integer support are mostly SAMD21 ("M0") boards without an external flash chip, such as the Adafruit Gemma M0, Trinket M0, QT Py M0, and the Trinkey series. There are also a number of third-party boards in this category. There are also a few small STM third-party boards without long integer support.
`time.localtime()`, `time.mktime()`, `time.time()`, and `time.monotonic_ns()` are available only on builds with long integers.
## Wireless Connectivity
###
How do I connect to the Internet with CircuitPython?
If you'd like to include WiFi in your project, your best bet is to use a board that is running natively on ESP32 chipsets - those have WiFi built in!
If your development board has an SPI port and at least 4 additional pins, you can check out [this guide](https://learn.adafruit.com/adafruit-io-basics-airlift) on using AirLift with CircuitPython - extra wiring is required and some boards like the MacroPad or NeoTrellis do not have enough available pins to add the hardware support.
For further project examples, and guides about using AirLift with specific hardware, check out [the Adafruit Learn System](https://learn.adafruit.com/search?q=airlift).
### How do I do BLE (Bluetooth Low Energy) with CircuitPython?
nRF52840, nRF52833, and **as of CircuitPython 9.1.0** , ESP32, ESP32-C3, and ESP32-S3 boards (with 8MB) have the most complete BLE implementation. Your program can act as both a BLE central and peripheral. As a central, you can scan for advertisements, and connect to an advertising board. As a peripheral, you can advertise, and you can create services available to a central. Pairing and bonding are supported.
**Most Espressif boards with only 4MB of flash do not have enough room to include BLE in CircuitPython 9.** Check the [Module Support Matrix](https://docs.circuitpython.org/en/latest/shared-bindings/support_matrix.html) to see if your board has support for `_bleio`. CircuitPython 10 is planned to support `_bleio` on Espressif boards with 4MB flash.
Note that the ESP32-S2 does not have Bluetooth capability.
On most other boards with adequate firmware space, [BLE is available for use with AirLift](https://learn.adafruit.com/adafruit-airlift-breakout/circuitpython-ble) or other NINA-FW-based co-processors. Some boards have this coprocessor on board, such as the [PyPortal](https://learn.adafruit.com/adafruit-pyportal/circuitpython-ble). Currently, this implementation only supports acting as a BLE peripheral. Scanning and connecting as a central are not yet implemented. Bonding and pairing are not supported.
###
Are there other ways to communicate by radio with CircuitPython?
Check out [Adafruit's RFM boards](https://www.adafruit.com/?q=rfm&sort=BestMatch)for simple radio communication supported by CircuitPython, which can be used over distances of 100m to over a km, depending on the version. The RFM SAMD21 M0 boards can be used, but they were not designed for CircuitPython, and have limited RAM and flash space; using the RFM breakouts or FeatherWings with more capable boards will be easier.
## Asyncio and Interrupts
###
Is there asyncio support in CircuitPython?
There is support for asyncio starting with CircuitPython 7.1.0, on all boards except the smallest SAMD21 builds. Read about using it in the [Cooperative Multitasking in CircuitPython](https://learn.adafruit.com/cooperative-multitasking-in-circuitpython) Guide.
###
Does CircuitPython support interrupts?
No. CircuitPython does not currently support interrupts - please use asyncio for multitasking / 'threaded' control of your code
## Status RGB LED
###
My RGB NeoPixel/DotStar LED is blinking funny colors - what does it mean?
The status LED can tell you what's going on with your CircuitPython board. [Read more here for what the colors mean!](https://learn.adafruit.com/welcome-to-circuitpython/troubleshooting#circuitpython-rgb-status-light-2978455-24)
## Memory Issues
###
What is a MemoryError?
Memory allocation errors happen when you're trying to store too much on the board. The CircuitPython microcontroller boards have a limited amount of memory available. You can have about 250 lines of code on the M0 Express boards. If you try to `import` too many libraries, a combination of large libraries, or run a program with too many lines of code, your code will fail to run and you will receive a `MemoryError` in the serial console.
###
What do I do when I encounter a MemoryError?
Try resetting your board. Each time you reset the board, it reallocates the memory. While this is unlikely to resolve your issue, it's a simple step and is worth trying.
Make sure you are using **.mpy** versions of libraries. All of the CircuitPython libraries are available in the bundle in a **.mpy** format which takes up less memory than **.py** format. Be sure that you're using [the latest library bundle](https://github.com/adafruit/Adafruit_CircuitPython_Bundle/releases) for your version of CircuitPython.
If that does not resolve your issue, try shortening your code. Shorten comments, remove extraneous or unneeded code, or any other clean up you can do to shorten your code. If you're using a lot of functions, you could try moving those into a separate library, creating a **.mpy** of that library, and importing it into your code.
You can turn your entire file into a **.mpy** and `import` that into **code.py**. This means you will be unable to edit your code live on the board, but it can save you space.
###
Can the order of my .mpy files?
You can make your own **.mpy** versions of files with `mpy-cross`.
You can download **mpy-cross** for your operating system from [here](https://adafruit-circuit-python.s3.amazonaws.com/index.html?prefix=bin/mpy-cross/). Builds are available for Windows, macOS, x64 Linux, and Raspberry Pi Linux. Choose the latest **mpy-cross** whose version matches the version of CircuitPython you are using.
On macOS and Linux, after you download **mpy-cross** , you must make the the file executable by doing `chmod +x name-of-the-mpy-cross-executable`.
To make a **.mpy** file, run `./mpy-cross path/to/yourfile.py` to create a **yourfile.mpy** in the same directory as the original file.
###
How do I check how much memory I have free?
Run the following to see the number of bytes available for use:
`import gc`
`gc.mem_free()`
## Unsupported Hardware
###
Is ESP8266 or ESP32 supported in CircuitPython? Why not?
We dropped ESP8266 support as of 4.x - For more information please read about it [here](https://learn.adafruit.com/welcome-to-circuitpython/circuitpython-for-esp8266)!
[As of CircuitPython 8.x we have started to support ESP32 and ESP32-C3 and have added a WiFi workflow for wireless coding!](https://learn.adafruit.com/circuitpython-with-esp32-quick-start)
We also support ESP32-S2 & ESP32-S3, which have native USB.
###
Does Feather M0 support WINC1500?
No, WINC1500 will not fit into the M0 flash space.
###
Can AVRs such as ATmega328 or ATmega2560 run CircuitPython?
No.
# Adafruit TRRS Trinkey
## Troubleshooting
From time to time, you will run into issues when working with CircuitPython. Here are a few things you may encounter and how to resolve them.
Danger:
# Always Run the Latest Version of CircuitPython and Libraries
As CircuitPython development continues and there are new releases, Adafruit will stop supporting older releases. **You need to [update to the latest CircuitPython.](https://circuitpython.org/downloads).**
You need to download the CircuitPython Library Bundle that matches your version of CircuitPython. **Please update CircuitPython and then [download the latest bundle](https://circuitpython.org/libraries)**.
As new versions of CircuitPython are released, Adafruit will stop providing the previous bundles as automatically created downloads on the Adafruit CircuitPython Library Bundle repo. If you must continue to use an earlier version, you can still download the appropriate version of `mpy-cross` from the particular release of CircuitPython on the CircuitPython repo and create your own compatible .mpy library files. **However, it is best to update to the latest for both CircuitPython and the library bundle.**
## I have to continue using CircuitPython 7.x or earlier. Where can I find compatible libraries?
**Adafruit is no longer building or supporting the CircuitPython 7.x or earlier library bundles. You are highly encourged to [update CircuitPython to the latest version](https://circuitpython.org/downloads) and use [the current version of the libraries](https://circuitpython.org/libraries).** However, if for some reason you cannot update, links to the previous bundles are available in the [FAQ](https://learn.adafruit.com/welcome-to-circuitpython/frequently-asked-questions#faq-3105289).
# macOS Sonoma before 14.4: Errors Writing to CIRCUITPY macOS 14.4 - 15.1: Slow Writes to CIRCUITPY
macOS Sonoma before 14.4 took many seconds to complete writes to small FAT drives, 8MB or smaller. This causes errors when writing to CIRCUITPY. The best solution was to remount the CIRCUITPY drive after it is automatically mounted. Or consider downgrading back to Ventura if that works for you. This problem was tracked in [CircuitPython GitHub issue 8449](https://github.com/adafruit/circuitpython/issues/8449).
Below is a shell script to do this remount conveniently (courtesy [@czei in GitHub](https://github.com/adafruit/circuitpython/issues/8449#issuecomment-1779981373)). Copy the code here into a file named, say, **remount-CIRCUITPY.sh**. Place the file in a directory on your PATH, or in some other convenient place.
macOS Sonoma 14.4 and versions of macOS before Sequoia 15.2 did not have the problem above, but did take an inordinately long time to write to FAT drives of size 1GB or less (40 times longer than 2GB drives). As of macOS 15.2, writes are no longer very slow. This problem was tracked in [CircuitPython GitHub issue 8918](https://github.com/adafruit/circuitpython/issues/8918).
```auto
#!/bin/sh
#
# This works around bug where, by default,
# macOS 14.x before 14.4 writes part of a file immediately,
# and then doesn't update the directory for 20-60 seconds, causing
# the file system to be corrupted.
#
disky=`df | grep CIRCUITPY | cut -d" " -f1`
sudo umount /Volumes/CIRCUITPY
sudo mkdir /Volumes/CIRCUITPY
sleep 2
sudo mount -v -o noasync -t msdos $disky /Volumes/CIRCUITPY
```
Then in a Terminal window, do this to make this script executable:
```terminal
chmod +x remount-CIRCUITPY.sh
```
Place the file in a directory on your `PATH`, or in some other convenient place.
Now, each time you plug in or reset your CIRCUITPY board, run the file **remount-CIRCUITPY.sh**. You can run it in a Terminal window or you may be able to place it on the desktop or in your dock to run it just by double-clicking.
This will be something of a nuisance but it is the safest solution.
This problem is being tracked in [this CircuitPython issue](https://github.com/adafruit/circuitpython/issues/8449).
# Bootloader (_boardname_BOOT) Drive Not Present
### **You may have a different board.**
Only Adafruit Express boards and the SAMD21 non-Express boards ship with the [UF2 bootloader](../../../adafruit-feather-m0-express-designed-for-circuit-python-circuitpython/uf2-bootloader?view=all#uf2-bootloader)installed. The Feather M0 Basic, Feather M0 Adalogger, and similar boards use a regular Arduino-compatible bootloader, which does not show a **_boardname_BOOT** drive.
### **MakeCode**
If you are running a [MakeCode](../../../makecode/sharing-and-saving?view=all#step-1-bootloader-mode) program on Circuit Playground Express, press the reset button just once to get the **CPLAYBOOT** drive to show up. Pressing it twice will not work.
### **macOS**
**DriveDx** and its accompanything **SAT SMART Driver** can interfere with seeing the BOOT drive. [See this forum post](https://forums.adafruit.com/viewtopic.php?f=58&t=161917&p=799309#p799215) for how to fix the problem.
### **Windows 10 or later**
Did you install the Adafruit Windows Drivers package by mistake, or did you upgrade to Windows 10 or later with the driver package installed? You don't need to install this package on Windows 10 or 11for most Adafruit boards. The old version (v1.5) can interfere with recognizing your device. Go to **Settings** -\> **Apps** and uninstall all the "Adafruit" driver programs.
### **Windows 7 or 8.1**
Windows 7 and 8.1 have reached end of life. It is [recommended](https://learn.adafruit.com/welcome-to-circuitpython/installing-circuitpython#windows-7-and-8-dot-1-drivers-2977910-9) that you upgrade to Windows 10 or 11 if possible. Drivers are available for some older CircuitPython boards, but there are no plans to release drivers for newer boards.
Info: The Windows Drivers installer was last updated in November 2020 (v2.5.0.0) . Windows 7 drivers for CircuitPython boards released since then, including RP2040 boards, are not available. There are no plans to release drivers for newer boards. The boards work fine on Windows 10 and later.
You should now be done! Test by unplugging and replugging the board. You should see the **CIRCUITPY** drive, and when you double-click the reset button (single click on Circuit Playground Express running MakeCode), you should see the appropriate **_boardname_BOOT** drive.
Let us know in the [Adafruit support forums](https://forums.adafruit.com) or on the [Adafruit Discord](https://adafru.it/discord) if this does not work for you!
# Windows Explorer Locks Up When Accessing **_boardname_BOOT** Drive
On Windows, several third-party programs that can cause issues. The symptom is that you try to access the **_boardname_BOOT** drive, and Windows or Windows Explorer seems to lock up. These programs are known to cause trouble:
- **AIDA64** : to fix, stop the program. This problem has been reported to AIDA64. They acquired hardware to test, and released a beta version that fixes the problem. This may have been incorporated into the latest release. Please let us know in the forums if you test this.
- **BitDefender anti-virus**
- **Hard Disk Sentinel**
- **Kaspersky anti-virus** : To fix, you may need to disable Kaspersky completely. Disabling some aspects of Kaspersky does not always solve the problem. This problem has been reported to Kaspersky.
- **ESET NOD32 anti-virus** : There have been problems with at least version 9.0.386.0, solved by uninstallation.
# Copying UF2 to **_boardname_BOOT** Drive Hangs at 0% Copied
On Windows, a **Western DIgital (WD) utility** that comes with their external USB drives can interfere with copying UF2 files to the **_boardname_BOOT** drive. Uninstall that utility to fix the problem.
# CIRCUITPY Drive Does Not Appear or Disappears Quickly
**BitDefender anti-virus has been reported to block access to** **CIRCUITPY**. You can set an exception for the drive letter.
Kaspersky **anti-virus** can block the appearance of the **CIRCUITPY** drive. There has not yet been settings change discovered that prevents this. Complete uninstallation of Kaspersky fixes the problem.
**Norton anti-virus** can interfere with **CIRCUITPY**. A user has reported this problem on Windows 7. The user turned off both Smart Firewall and Auto Protect, and **CIRCUITPY** then appeared.
**Sophos Endpoint** security software [can cause CIRCUITPY to disappear](https://forums.adafruit.com/viewtopic.php?f=60&t=187629) and the BOOT drive to reappear. It is not clear what causes this behavior.
**Samsung Magician** can cause CIRCUITPY to disappear (reported [here](https://forums.adafruit.com/viewtopic.php?t=205159) and [here](https://forums.adafruit.com/viewtopic.php?p=987596#p987596)).
## "M105" Seen on Display, Crashes, Missing CIRCUITPY
The **Cura** 3D printing program sends 3D printing GCODE commands to unused serial ports to try to find 3D printers connected over serial. This causes a variety of problems. Disable (uncheck) **USB Printing** in Cura in the **Market** -\> **Installed** menu, or uninstall Cura. For more information see [this forum post](https://forums.adafruit.com/viewtopic.php?t=192784), [this CircuitPython issue](https://github.com/adafruit/circuitpython/issues/2585), and [this Cura issue](https://github.com/Ultimaker/Cura/issues/5207).
# Device Errors or Problems on Windows
Windows can become confused about USB device installations. Try cleaning up your USB devices. Use [Uwe Sieber's Device Cleanup Tool](https://www.uwe-sieber.de/misc_tools_e.html) (on that page, scroll down to "Device Cleanup Tool"). Download and unzip the tool. Unplug all the boards and other USB devices you want to clean up. Run the tool as Administrator. You will see a listing like this, probably with many more devices. It is listing all the USB devices that are _not_ currently attached.
Select all the devices you want to remove, and then press Delete. It is usually safe just to select everything. Any device that is removed will get a fresh install when you plug it in. Using the Device Cleanup Tool also discards all the COM port assignments for the unplugged boards. If you have used many Arduino and CircuitPython boards, you have probably seen higher and higher COM port numbers used, seemingly without end. This will fix that problem.
# Serial Console in Mu Not Displaying Anything
There are times when the serial console will accurately not display anything, such as, when no code is currently running, or when code with no serial output is already running before you open the console. However, if you find yourself in a situation where you feel it should be displaying something like an error, consider the following.
Depending on the size of your screen or Mu window, when you open the serial console, the serial console panel may be very small. This can be a problem. A basic CircuitPython error takes 10 lines to display!
```
Auto-reload is on. Simply save files over USB to run them or enter REPL to disable.
code.py output:
Traceback (most recent call last):
File "code.py", line 7
SyntaxError: invalid syntax
Press any key to enter the REPL. Use CTRL-D to reload.
```
More complex errors take even more lines!
Therefore, if your serial console panel is five lines tall or less, you may only see blank lines or blank lines followed by `Press any key to enter the REPL. Use CTRL-D to reload.`. If this is the case, you need to either mouse over the top of the panel to utilise the option to resize the serial panel, or use the scrollbar on the right side to scroll up and find your message.
This applies to any kind of serial output whether it be error messages or print statements. So before you start trying to debug your problem on the hardware side, be sure to check that you haven't simply missed the serial messages due to serial output panel height.
# code.py Restarts Constantly
CircuitPython will restart **code.py** if you or your computer writes to something on the CIRCUITPY drive. This feature is called _auto-reload_, and lets you test a change to your program immediately.
Some utility programs, such as backup, anti-virus, or disk-checking apps, will write to the CIRCUITPY as part of their operation. Sometimes they do this very frequently, causing constant restarts.
**Acronis True Image** and related Acronis programs on Windows are known to cause this problem. It is possible to prevent this by [disabling the "](https://forum.acronis.com/forum/acronis-true-image-2018-forum/acronis-ati-2018-contantly-touch-usb-port-causing-issue-adafruit-circuitpython-folder)[Acronis Managed Machine Service Mini"](https://forum.acronis.com/forum/acronis-true-image-2018-forum/acronis-ati-2018-contantly-touch-usb-port-causing-issue-adafruit-circuitpython-folder).
If you cannot stop whatever is causing the writes, you can disable auto-reload by putting this code in **boot.py** or **code.py** :
```python
import supervisor
supervisor.runtime.autoreload = False
```
# CircuitPython RGB Status Light
Nearly all CircuitPython-capable boards have a single NeoPixel or DotStar RGB LED on the board that indicates the status of CircuitPython. A few boards designed before CircuitPython existed, such as the Feather M0 Basic, do not.
**Circuit Playground Express and Circuit Playground Bluefruit have multiple RGB LEDs, but do NOT have a status LED. The LEDs are all green when in the bootloader. In versions before 7.0.0, they do NOT indicate any status while running CircuitPython.**
## **CircuitPython 7.0.0 and Later**
The status LED blinks were changed in CircuitPython 7.0.0 in order to save battery power and simplify the blinks. These blink patterns will occur on single color LEDs when the board does not have any RGB LEDs. Speed and blink count also vary for this reason.
On start up, the LED will blink **YELLOW** multiple times for 1 second. Pressing the RESET button (or on Espressif, the BOOT button) during this time will restart the board and then enter safe mode. On Bluetooth capable boards, after the yellow blinks, there will be a set of faster blue blinks. Pressing reset during the **BLUE** blinks will clear Bluetooth information and start the device in discoverable mode, so it can be used with a BLE code editor.
Once started, CircuitPython will blink a pattern every 5 seconds when no user code is running to indicate why the code stopped:
- 1 **GREEN** blink: Code finished without error.
- 2 **RED** blinks: Code ended due to an exception. Check the serial console for details.
- 3 **YELLOW** blinks: CircuitPython is in safe mode. No user code was run. Check the serial console for safe mode reason.
When in the REPL, CircuitPython will set the status LED to **WHITE**. You can change the LED color from the REPL. The status indicator will not persist on non-NeoPixel or DotStar LEDs.
## **CircuitPython 6.3.0 and earlier**
Here's what the colors and blinking mean:
- steady **GREEN** : **code.py** (or **code.txt** , **main.py** , or **main.txt** ) is running
- pulsing **GREEN** : **code.py** (etc.) has finished or does not exist
- steady **YELLOW** at start up: (4.0.0-alpha.5 and newer) CircuitPython is waiting for a reset to indicate that it should start in safe mode
- pulsing **YELLOW** : Circuit Python is in safe mode: it crashed and restarted
- steady **WHITE** : REPL is running
- steady **BLUE** : **boot.py** is running
Colors with multiple flashes following indicate a Python exception and then indicate the line number of the error. The color of the first flash indicates the type of error:
- **GREEN** : IndentationError
- **CYAN** : SyntaxError
- **WHITE** : NameError
- **ORANGE** : OSError
- **PURPLE** : ValueError
- **YELLOW** : other error
These are followed by flashes indicating the line number, including place value. **WHITE** flashes are thousands' place, **BLUE** are hundreds' place, **YELLOW** are tens' place, and **CYAN** are one's place. So for example, an error on line 32 would flash **YELLOW** three times and then **CYAN** two times. Zeroes are indicated by an extra-long dark gap.
# Serial console showing `ValueError: Incompatible .mpy file`
This error occurs when importing a module that is stored as a **.mpy** binary file that was generated by a different version of CircuitPython than the one its being loaded into. In particular, the mpy binary format changed between CircuitPython versions 6.x and 7.x, 2.x and 3.x, and 1.x and 2.x.
So, for instance, if you upgraded to CircuitPython 7.x from 6.x you’ll need to download a newer version of the library that triggered the error on `import`. All libraries are available in the [Adafruit bundle](https://github.com/adafruit/Adafruit_CircuitPython_Bundle/releases/latest).
# CIRCUITPY Drive Issues
You may find that you can no longer save files to your **CIRCUITPY** drive. You may find that your **CIRCUITPY** stops showing up in your file explorer, or shows up as **NO\_NAME**. These are indicators that your filesystem has issues. When the **CIRCUITPY** disk is not safely ejected before being reset by the button or being disconnected from USB, it may corrupt the flash drive. It can happen on Windows, Mac or Linux, though it is more common on Windows.
Be aware, if you have used Arduino to program your board, CircuitPython is no longer able to provide the USB services. You will need to reload CircuitPython to resolve this situation.
The easiest first step is to reload CircuitPython. Double-tap reset on the board so you get a **_boardname_BOOT** drive rather than a **CIRCUITPY** drive, and copy the latest version of CircuitPython ( **.uf2** ) back to the board. This may restore **CIRCUITPY** functionality.
If reloading CircuitPython does not resolve your issue, the next step is to try putting the board into safe mode.
## Safe Mode
Whether you've run into a situation where you can no longer edit your **code.py** on your **CIRCUITPY** drive, your board has gotten into a state where **CIRCUITPY** is read-only, or you have turned off the **CIRCUITPY** drive altogether, safe mode can help.
**Safe mode** in CircuitPython does not run any user code on startup, and disables auto-reload. This means a few things. First, safe mode _bypasses any code in_ **boot.py** (where you can set **CIRCUITPY** read-only or turn it off completely). Second, _it does not run the code in_ **code.py**. And finally, _it does not automatically soft-reload when data is written to the_ **CIRCUITPY** _drive_.
Therefore, whatever you may have done to put your board in a non-interactive state, safe mode gives you the opportunity to correct it without losing all of the data on the **CIRCUITPY** drive.
### Entering Safe Mode in CircuitPython 7.x and Later
You can enter safe by pressing reset during the right time when the board boots. Immediately after the board starts up or resets, it waits one second. On some boards, the onboard status LED will blink yellow during that time. If you press reset during that one second period, the board will start up in safe mode. It can be difficult to react to the yellow LED, so you may want to think of it simply as a "slow" double click of the reset button. (Remember, a fast double click of reset enters the bootloader.)
### Entering Safe Mode in CircuitPython 6.x
You can enter safe by pressing reset during the right time when the board boots.. Immediately after the board starts up or resets, it waits 0.7 seconds. On some boards, the onboard status LED (highlighted in green above) will turn solid yellow during this time. If you press reset during that 0.7 seconds, the board will start up in safe mode. It can be difficult to react to the yellow LED, so you may want to think of it simply as a slow double click of the reset button. (Remember, a fast double click of reset enters the bootloader.)
### In Safe Mode
Once you've entered safe mode successfully in CircuitPython 6.x, the LED will pulse yellow.
If you successfully enter safe mode on CircuitPython 7.x, the LED will intermittently blink yellow three times.
If you connect to the serial console, you'll find the following message.
```terminal
Auto-reload is off.
Running in safe mode! Not running saved code.
CircuitPython is in safe mode because you pressed the reset button during boot. Press again to exit safe mode.
Press any key to enter the REPL. Use CTRL-D to reload.
```
You can now edit the contents of the **CIRCUITPY** drive. Remember, _your code will not run until you press the reset button, or unplug and plug in your board, to get out of safe mode._
At this point, you'll want to remove any user code in **code.py** and, if present, the **boot.py** file from **CIRCUITPY**. Once removed, tap the reset button, or unplug and plug in your board, to restart CircuitPython. This will restart the board and may resolve your drive issues. If resolved, you can begin coding again as usual.
If safe mode does not resolve your issue, the board must be completely erased and CircuitPython must be reloaded onto the board.
Danger:
## To erase CIRCUITPY: `storage.erase_filesystem()`
CircuitPython includes a built-in function to erase and reformat the filesystem. If you have a version of CircuitPython older than 2.3.0 on your board, you can [update to the newest version](../../../../welcome-to-circuitpython/installing-circuitpython) to do this.
1. [Connect to the CircuitPython REPL](../../../../welcome-to-circuitpython/kattni-connecting-to-the-serial-console) using Mu or a terminal program.
2. Type the following into the REPL:
```terminal
>>> import storage
>>> storage.erase_filesystem()
```
CIRCUITPY will be erased and reformatted, and your board will restart. That's it!
## Erase CIRCUITPY Without Access to the REPL
If you can't access the REPL, or you're running a version of CircuitPython previous to 2.3.0 and you don't want to upgrade, there are options available for some specific boards.
**The options listed below are considered to be the "old way" of erasing your board. The method shown above using the REPL is highly recommended as the best method for erasing your board.**
Warning:
## For the specific boards listed below:
If the board you are trying to erase is listed below, follow the steps to use the file to erase your board.
1. Download the correct erase file:
[Circuit Playground Express](https://cdn-learn.adafruit.com/assets/assets/000/048/745/original/flash_erase_express.ino.circuitplay.uf2?1512152080)
[Feather M0 Express](https://cdn-learn.adafruit.com/assets/assets/000/048/746/original/flash_erase_express.ino.feather_m0_express.uf2?1512152098)
[Feather M4 Express](https://cdn-learn.adafruit.com/assets/assets/000/076/217/original/flash_erase.ino.feather_m4.uf2)
[Metro M0 Express](https://cdn-learn.adafruit.com/assets/assets/000/048/747/original/flash_erase_express.ino.metro_m0.uf2?1512152103)
[Metro M4 Express QSPI Eraser](https://cdn-learn.adafruit.com/assets/assets/000/073/820/original/Metro_M4_QSPI_Eraser.UF2?1553805937)
[Trellis M4 Express (QSPI)](https://cdn-learn.adafruit.com/assets/assets/000/067/535/original/Trellis_M4_QSPI_Eraser.UF2?1544719380)
[Grand Central M4 Express (QSPI)](https://cdn-learn.adafruit.com/assets/assets/000/069/314/original/GC_M4_QSPI_Erase.UF2?1547404471)
[PyPortal M4 Express (QSPI)](https://cdn-learn.adafruit.com/assets/assets/000/072/252/original/PYPORTAL_QSPI_Eraser.UF2?1551738305)
[Circuit Playground Bluefruit (QSPI)](https://cdn-learn.adafruit.com/assets/assets/000/082/950/original/CP_Bluefruit_QSPI_Erase.UF2?1572026649)
[Monster M4SK (QSPI)](https://cdn-learn.adafruit.com/assets/assets/000/083/330/original/M4SK_QSPI_Eraser.UF2?1572551433)
[PyBadge/PyGamer QSPI Eraser.UF2](https://cdn-learn.adafruit.com/assets/assets/000/083/331/original/PyBadge_QSPI_Eraser.UF2?1572551613)
[CLUE_Flash_Erase.UF2](https://cdn-learn.adafruit.com/assets/assets/000/088/454/original/CLUE_Flash_Erase.UF2?1581873830)
[Matrix_Portal_M4_(QSPI).UF2](https://cdn-learn.adafruit.com/assets/assets/000/098/741/original/Matrix_Portal_M4_%28QSPI%29.UF2?1611076081)
[RP2040 boards (flash_nuke.uf2)](https://cdn-learn.adafruit.com/assets/assets/000/101/659/original/flash_nuke.uf2)
2. Double-click the reset button on the board to bring up the **_boardname_BOOT** drive.
3. Drag the erase **.uf2** file to the **_boardname_BOOT** drive.
4. The status LED will turn yellow or blue, indicating the erase has started.
5. After approximately 15 seconds, the status LED will light up green. On the NeoTrellis M4 this is the first NeoPixel on the grid
6. Double-click the reset button on the board to bring up the **_boardname_BOOT** drive.
7. [Drag the appropriate latest release of CircuitPython](https://circuitpython.org/downloads) **.uf2** file to the **_boardname_BOOT** drive.
It should reboot automatically and you should see **CIRCUITPY** in your file explorer again.
If the LED flashes red during step 5, it means the erase has failed. Repeat the steps starting with 2.
[If you haven't already downloaded the latest release of CircuitPython for your board, check out the installation page](../../../../welcome-to-circuitpython/installing-circuitpython). You'll also need to load your code and reinstall your libraries!
## For SAMD21 non-Express boards that have a UF2 bootloader:
Any SAMD21-based microcontroller that does not have external flash available is considered a SAMD21 non-Express board. Non-Express boards that have a UF2 bootloader include Trinket M0, GEMMA M0, QT Py M0, and the SAMD21-based Trinkey boards.
If you are trying to erase a SAMD21 non-Express board, follow these steps to erase your board.
1. Download the erase file:
[SAMD21 non-Express Boards](https://cdn-learn.adafruit.com/assets/assets/000/048/748/original/erase_m0.uf2)
2. Double-click the reset button on the board to bring up the **_boardname_BOOT** drive.
3. Drag the erase **.uf2** file to the **_boardname_BOOT** drive.
4. The boot LED will start flashing again, and the **_boardname_BOOT** drive will reappear.
5. [Drag the appropriate latest release CircuitPython](https://circuitpython.org/downloads) **.uf2** file to the _boardname_BOOT drive.
It should reboot automatically and you should see **CIRCUITPY** in your file explorer again.
[If you haven't already downloaded the latest release of CircuitPython for your board, check out the installation page](../../../../welcome-to-circuitpython/installing-circuitpython) YYou'll also need to load your code and reinstall your libraries!
## For SAMD21 non-Express boards that do not have a UF2 bootloader:
Any SAMD21-based microcontroller that does not have external flash available is considered a SAMD21 non-Express board. Non-Express boards that do **not** have a UF2 bootloader include the Feather M0 Basic Proto, Feather Adalogger, or the Arduino Zero.
If you are trying to erase a non-Express board that does not have a UF2 bootloader, [follow these directions to reload CircuitPython using `bossac`](../../../../welcome-to-circuitpython/non-uf2-installation), which will erase and re-create **CIRCUITPY**.
# Running Out of File Space on SAMD21 Non-Express Boards
Any SAMD21-based microcontroller that does not have external flash available is considered a SAMD21 non-Express board. This includes boards like the Trinket M0, GEMMA M0, QT Py M0, and the SAMD21-based Trinkey boards.
The file system on the board is very tiny. (Smaller than an ancient floppy disk.) So, its likely you'll run out of space but don't panic! There are a number of ways to free up space.
## Delete something!
The simplest way of freeing up space is to delete files from the drive. Perhaps there are libraries in the **lib** folder that you aren't using anymore or test code that isn't in use. Don't delete the **lib** folder completely, though, just remove what you don't need.
The board ships with the Windows 7 serial driver too! Feel free to delete that if you don't need it or have already installed it. It's ~12KiB or so.
## Use tabs
One unique feature of Python is that the indentation of code matters. Usually the recommendation is to indent code with four spaces for every indent. In general, that is recommended too. **However** , one trick to storing more human-readable code is to use a single tab character for indentation. This approach uses 1/4 of the space for indentation and can be significant when you're counting bytes.
## On macOS?
MacOS loves to generate hidden files. Luckily you can disable some of the extra hidden files that macOS adds by running a few commands to disable search indexing and create zero byte placeholders. Follow the steps below to maximize the amount of space available on macOS.
## Prevent & Remove macOS Hidden Files
First find the volume name for your board. With the board plugged in run this command in a terminal to list all the volumes:
```
ls -l /Volumes
```
Look for a volume with a name like **CIRCUITPY** (the default for CircuitPython). The full path to the volume is the **/Volumes/CIRCUITPY** path.
Now follow the [steps from this question](http://apple.stackexchange.com/questions/6707/how-to-stop-os-x-from-writing-spotlight-and-trash-files-to-memory-cards-and-usb/7135#7135) to run these terminal commands that stop hidden files from being created on the board:
```terminal
mdutil -i off /Volumes/CIRCUITPY
cd /Volumes/CIRCUITPY
rm -rf .{,_.}{fseventsd,Spotlight-V*,Trashes}
mkdir .fseventsd
touch .fseventsd/no_log .metadata_never_index .Trashes
cd -
```
Replace **/Volumes/CIRCUITPY** in the commands above with the full path to your board's volume if it's different. At this point all the hidden files should be cleared from the board and some hidden files will be prevented from being created.
Alternatively, with CircuitPython 4.x and above, the special files and folders mentioned above will be created automatically if you erase and reformat the filesystem. **WARNING: Save your files first!** Do this in the REPL:
`>>> import storage`
`>>> storage.erase_filesystem()`
However there are still some cases where hidden files will be created by MacOS. In particular if you copy a file that was downloaded from the internet it will have special metadata that MacOS stores as a hidden file. Luckily you can run a copy command from the terminal to copy files **without** this hidden metadata file. See the steps below.
## Copy Files on macOS Without Creating Hidden Files
Once you've disabled and removed hidden files with the above commands on macOS you need to be careful to copy files to the board with a special command that prevents future hidden files from being created. Unfortunately you **cannot** use drag and drop copy in Finder because it will still create these hidden extended attribute files in some cases (for files downloaded from the internet, like Adafruit's modules).
To copy a file or folder use the **-X** option for the **cp** command in a terminal. For example to copy a **file\_name.mpy** file to the board use a command like:
```terminal
cp -X file_name.mpy /Volumes/CIRCUITPY
```
(Replace **file\_name.mpy** with the name of the file you want to copy.)
Or to copy a folder and all of the files and folders contained within, use a command like:
```terminal
cp -rX folder_to_copy /Volumes/CIRCUITPY
```
If you are copying to the **lib** folder, or another folder, make sure it exists before copying.
```terminal
# if lib does not exist, you'll create a file named lib !
cp -X file_name.mpy /Volumes/CIRCUITPY/lib
# This is safer, and will complain if a lib folder does not exist.
cp -X file_name.mpy /Volumes/CIRCUITPY/lib/
```
## Other macOS Space-Saving Tips
If you'd like to see the amount of space used on the drive and manually delete hidden files here's how to do so. First, move into the **Volumes/** directory with `cd /Volumes/`, and then list the amount of space used on the **CIRCUITPY** drive with the `df` command.
That's not very much space left! The next step is to show a list of the files currently on the **CIRCUITPY** drive, _including_ the hidden files, using the `ls` command. You cannot use Finder to do this, you must do it via command line!
There are a few of the hidden files that MacOS loves to generate, all of which begin with a **.\_** before the file name. Remove the **.\_** files using the `rm` command. You can remove them all once by running `rm CIRCUITPY/._*`. The `*` acts as a _wildcard_ to apply the command to everything that begins with **.\_** at the same time.
Finally, you can run `df` again to see the current space used.
Nice! You have 12Ki more than before! This space can now be used for libraries and code!
# Device Locked Up or Boot Looping
In rare cases, it may happen that something in your **code.py** or **boot.py** files causes the device to get locked up, or even go into a boot loop. A _boot loop_ occurs when the board reboots repeatedly and never fully loads. These are not caused by your everyday Python exceptions, typically it's the result of a deeper problem within CircuitPython. In this situation, it can be difficult to recover your device if **CIRCUITPY** is not allowing you to modify the **code.py** or **boot.py** files. Safe mode is one recovery option. When the device boots up in safe mode it will not run the **code.py** or **boot.py** scripts, but will still connect the **CIRCUITPY** drive so that you can remove or modify those files as needed.
For more information on safe mode and how to enter safe mode, see the [Safe Mode section on this page](https://learn.adafruit.com/welcome-to-circuitpython/troubleshooting#safe-mode-3105351).
# Adafruit TRRS Trinkey
## "Uninstalling" CircuitPython
A lot of our boards can be used with multiple programming languages. For example, the Circuit Playground Express can be used with MakeCode, Code.org CS Discoveries, CircuitPython and Arduino.
Maybe you tried CircuitPython and want to go back to MakeCode or Arduino? Not a problem. You can always remove or reinstall CircuitPython _whenever you want!_ Heck, you can change your mind every day!
**There is nothing to uninstall.** CircuitPython is "just another program" that is loaded onto your board. You simply load another program (Arduino or MakeCode) and it will overwrite CircuitPython.
## Backup Your Code
Before replacing CircuitPython, don't forget to make a backup of the code you have on the **CIRCUITPY** drive. That means your **code.py** any other files, the **lib** folder etc. You may lose these files when you remove CircuitPython, so backups are key! Just drag the files to a folder on your laptop or desktop computer like you would with any USB drive.
# Moving Circuit Playground Express to MakeCode
On the Circuit Playground Express ( **this currently does NOT apply to Circuit Playground Bluefruit** ), if you want to go back to using MakeCode, it's really easy. Visit [makecode.adafruit.com](https://makecode.adafruit.com) and find the program you want to upload. Click Download to download the **.uf2** file that is generated by MakeCode.
Now double-click your CircuitPython board until you see the onboard LED(s) turn green and the **...BOOT** directory shows up.
Then find the downloaded MakeCode **.uf2** file and drag it to the **CPLAYBOOT** drive.
Your MakeCode is now running and CircuitPython has been removed. Going forward you only have to **single click** the reset button to get to **CPLAYBOOT**. This is an idiosyncrasy of MakeCode.
# Moving to Arduino
If you want to use Arduino instead, you just use the Arduino IDE to load an Arduino program. Here's an example of uploading a simple "Blink" Arduino program, but you don't have to use this particular program.
Start by plugging in your board, and double-clicking reset until you get the green onboard LED(s).
Within Arduino IDE, select the matching board, say Circuit Playground Express.
Select the correct matching Port:
Create a new simple Blink sketch example:
```
// the setup function runs once when you press reset or power the board
void setup() {
// initialize digital pin 13 as an output.
pinMode(13, OUTPUT);
}
// the loop function runs over and over again forever
void loop() {
digitalWrite(13, HIGH); // turn the LED on (HIGH is the voltage level)
delay(1000); // wait for a second
digitalWrite(13, LOW); // turn the LED off by making the voltage LOW
delay(1000); // wait for a second
}
```
Make sure the LED(s) are still green, then click **Upload** to upload Blink. Once it has uploaded successfully, the serial Port will change so **re-select the new Port**!
Once Blink is uploaded you should no longer need to double-click to enter bootloader mode. Arduino will automatically reset when you upload.
# Adafruit TRRS Trinkey
## Welcome to the Community!
CircuitPython is a programming language that's super simple to get started with and great for learning. It runs on microcontrollers and works out of the box. You can plug it in and get started with any text editor. The best part? CircuitPython comes with an amazing, supportive community.
Everyone is welcome! CircuitPython is Open Source. This means it's available for anyone to use, edit, copy and improve upon. This also means CircuitPython becomes better because of you being a part of it. Whether this is your first microcontroller board or you're a seasoned software engineer, you have something important to offer the Adafruit CircuitPython community. This page highlights some of the many ways you can be a part of it!
## Adafruit Discord
The Adafruit Discord server is the best place to start. Discord is where the community comes together to volunteer and provide live support of all kinds. From general discussion to detailed problem solving, and everything in between, Discord is a digital maker space with makers from around the world.
There are many different channels so you can choose the one best suited to your needs. Each channel is shown on Discord as "#channelname". There's the #help-with-projects channel for assistance with your current project or help coming up with ideas for your next one. There's the #show-and-tell channel for showing off your newest creation. Don't be afraid to ask a question in any channel! If you're unsure, #general is a great place to start. If another channel is more likely to provide you with a better answer, someone will guide you.
The help with CircuitPython channel is where to go with your CircuitPython questions. #help-with-circuitpython is there for new users and developers alike so feel free to ask a question or post a comment! Everyone of any experience level is welcome to join in on the conversation. Your contributions are important! The #circuitpython-dev channel is available for development discussions as well.
The easiest way to contribute to the community is to assist others on Discord. Supporting others doesn't always mean answering questions. Join in celebrating successes! Celebrate your mistakes! Sometimes just hearing that someone else has gone through a similar struggle can be enough to keep a maker moving forward.
The Adafruit Discord is the 24x7x365 hackerspace that you can bring your granddaughter to.
Visit [https://adafru.it/discord](https://adafru.it/discord)to sign up for Discord. Everyone is looking forward to meeting you!
## CircuitPython.org
Beyond the Adafruit Learn System, which you are viewing right now, the best place to find information about CircuitPython is [circuitpython.org](https://circuitpython.org). Everything you need to get started with your new microcontroller and beyond is available. You can do things like [download CircuitPython for your microcontroller](https://circuitpython.org/downloads) or [download the latest CircuitPython Library bundle](https://circuitpython.org/libraries), or check out [which single board computers support Blinka](https://circuitpython.org/blinka). You can also get to various other CircuitPython related things like Awesome CircuitPython or the Python for Microcontrollers newsletter. This is all incredibly useful, but it isn't necessarily community related. So why is it included here? The [Contributing page](https://circuitpython.org/contributing).
CircuitPython itself is written in C. However, all of the Adafruit CircuitPython libraries are written in _Python_. If you're interested in contributing to CircuitPython on the Python side of things, check out [circuitpython.org/contributing](https://circuitpython.org/contributing). You'll find information pertaining to every Adafruit CircuitPython library GitHub repository, giving you the opportunity to join the community by finding a contributing option that works for you.
Note the date on the page next to **Current Status for** :
If you submit any contributions to the libraries, and do not see them reflected on the Contributing page, it could be that the job that checks for new updates hasn't yet run for today. Simply check back tomorrow!
Now, a look at the different options.
### Pull Requests
The first tab you'll find is a list of **open pull requests**.
GitHub pull requests, or PRs, are opened when folks have added something to an Adafruit CircuitPython library GitHub repo, and are asking for Adafruit to add, or merge, their changes into the main library code. For PRs to be merged, they must first be reviewed. Reviewing is a great way to contribute! Take a look at the list of open pull requests, and pick one that interests you. If you have the hardware, you can test code changes. If you don't, you can still check the code updates for syntax. In the case of documentation updates, you can verify the information, or check it for spelling and grammar. Once you've checked out the update, you can leave a comment letting us know that you took a look. Once you've done that for a while, and you're more comfortable with it, you can consider joining the CircuitPythonLibrarians review team. The more reviewers we have, the more authors we can support. Reviewing is a crucial part of an open source ecosystem, CircuitPython included.
### Open Issues
The second tab you'll find is a list of **open issues**.
GitHub issues are filed for a number of reasons, including when there is a bug in the library or example code, or when someone wants to make a feature request. Issues are a great way to find an opportunity to contribute directly to the libraries by updating code or documentation. If you're interested in contributing code or documentation, take a look at the open issues and find one that interests you.
If you're not sure where to start, you can search the issues by label. Labels are applied to issues to make the goal easier to identify at a first glance, or to indicate the difficulty level of the issue. Click on the dropdown next to "Sort by issue labels" to see the list of available labels, and click on one to choose it.
If you're new to everything, new to contributing to open source, or new to contributing to the CircuitPython project, you can choose "Good first issue". Issues with that label are well defined, with a finite scope, and are intended to be easy for someone new to figure out.
If you're looking for something a little more complicated, consider "Bug" or "Enhancement". The Bug label is applied to issues that pertain to problems or failures found in the library. The Enhancement label is applied to feature requests.
Don't let the process intimidate you. If you're new to Git and GitHub, there is [a guide](https://learn.adafruit.com/contribute-to-circuitpython-with-git-and-github) to walk you through the entire process. As well, there are always folks available on [Discord](https:adafru.it/discord) to answer questions.
### Library Infrastructure Issues
The third tab you'll find is a list of **library infrastructure issues**.
This section is generated by a script that runs checks on the libraries, and then reports back where there may be issues. It is made up of a list of subsections each containing links to the repositories that are experiencing that particular issue. This page is available mostly for internal use, but you may find some opportunities to contribute on this page. If there's an issue listed that sounds like something you could help with, mention it on Discord, or file an issue on GitHub indicating you're working to resolve that issue. Others can reply either way to let you know what the scope of it might be, and help you resolve it if necessary.
### CircuitPython Localization
The fourth tab you'll find is the **CircuitPython Localization** tab.
If you speak another language, you can help translate CircuitPython! The translations apply to informational and error messages that are within the CircuitPython core. It means that folks who do not speak English have the opportunity to have these messages shown to them in their own language when using CircuitPython. This is incredibly important to provide the best experience possible for all users. CircuitPython uses Weblate to translate, which makes it much simpler to contribute translations. You will still need to know some CircuitPython-specific practices and a few basics about coding strings, but as with any CircuitPython contributions, folks are there to help.
Regardless of your skill level, or how you want to contribute to the CircuitPython project, there is an opportunity available. The [Contributing page](https://circuitpython.org/contributing) is an excellent place to start!
## Adafruit GitHub
Whether you're just beginning or are life-long programmer who would like to contribute, there are ways for everyone to be a part of the CircuitPython project. The CircuitPython core is written in C. The libraries are written in Python. GitHub is the best source of ways to contribute to the [CircuitPython core](https://github.com/adafruit/circuitpython), and the [CircuitPython libraries](https://circuitpython.org/contributing/open-issues). If you need an account, visit [https://github.com/](https://github.com/) and sign up.
If you're new to GitHub or programming in general, there are great opportunities for you. For the CircuitPython core, head over to the CircuitPython repository on GitHub, click on "[Issues](https://github.com/adafruit/circuitpython/issues)", and you'll find a list that includes issues labeled "[good first issue](https://github.com/adafruit/circuitpython/issues?q=is%3Aissue+is%3Aopen+label%3A%22good+first+issue%22)". For the libraries, head over to the [Contributing page Issues list](https://circuitpython.org/contributing/open-issues), and use the drop down menu to search for "[good first issue](https://circuitpython.org/contributing/open-issues?label=good-first-issue)". These issues are things that have been identified as something that someone with any level of experience can help with. These issues include options like updating documentation, providing feedback, and fixing simple bugs. If you need help getting started with GitHub, there is an excellent guide on [Contributing to CircuitPython with Git and GitHub](https://learn.adafruit.com/contribute-to-circuitpython-with-git-and-github).
Already experienced and looking for a challenge? Checkout the rest of either issues list and you'll find plenty of ways to contribute. You'll find all sorts of things, from new driver requests, to library bugs, to core module updates. There's plenty of opportunities for everyone at any level!
When working with or using CircuitPython or the CircuitPython libraries, you may find problems. If you find a bug, that's great! The team loves bugs! Posting a detailed issue to GitHub is an invaluable way to contribute to improving CircuitPython. For CircuitPython itself, file an issue [here](https://github.com/adafruit/circuitpython/issues). For the libraries, file an issue on the specific library repository on GitHub. Be sure to include the steps to replicate the issue as well as any other information you think is relevant. The more detail, the better!
Testing new software is easy and incredibly helpful. Simply load the newest version of CircuitPython or a library onto your CircuitPython hardware, and use it. Let us know about any problems you find by posting a new issue to GitHub. Software testing on both stable and unstable releases is a very important part of contributing CircuitPython. The developers can't possibly find all the problems themselves! They need your help to make CircuitPython even better.
On GitHub, you can submit feature requests, provide feedback, report problems and much more. If you have questions, remember that Discord and the Forums are both there for help!
## Adafruit Forums
The [Adafruit Forums](https://forums.adafruit.com) are the perfect place for support. Adafruit has wonderful paid support folks to answer any questions you may have. Whether your hardware is giving you issues or your code doesn't seem to be working, the forums are always there for you to ask. You need an Adafruit account to post to the forums. You can use the same account you use to order from Adafruit.
While Discord may provide you with quicker responses than the forums, the forums are a more reliable source of information. If you want to be certain you're getting an Adafruit-supported answer, the forums are the best place to be.
There are forum categories that cover all kinds of topics, including everything Adafruit. The [Adafruit CircuitPython](https://forums.adafruit.com/viewforum.php?f=60) category under "Supported Products & Projects" is the best place to post your CircuitPython questions.
Be sure to include the steps you took to get to where you are. If it involves wiring, post a picture! If your code is giving you trouble, include your code in your post! These are great ways to make sure that there's enough information to help you with your issue.
You might think you're just getting started, but you definitely know something that someone else doesn't. The great thing about the forums is that you can help others too! Everyone is welcome and encouraged to provide constructive feedback to any of the posted questions. This is an excellent way to contribute to the community and share your knowledge!
## Read the Docs
[Read the Docs](https://circuitpython.readthedocs.io/) is a an excellent resource for a more detailed look at the CircuitPython core and the CircuitPython libraries. This is where you'll find things like API documentation and example code. For an in depth look at viewing and understanding Read the Docs, check out the [CircuitPython Documentation](https://learn.adafruit.com/welcome-to-circuitpython/circuitpython-documentation) page!
# Adafruit TRRS Trinkey
## CircuitPython Essentials
You've been introduced to CircuitPython, and worked through getting everything set up. What's next? CircuitPython Essentials!
There are a number of core modules built into CircuitPython, which can be used along side the many CircuitPython libraries available. The following pages demonstrate some of these modules. Each page presents a different concept including a code example with an explanation. All of the examples are designed to work with your microcontroller board.
Time to get started learning the CircuitPython essentials!
# Adafruit TRRS Trinkey
## NeoPixel Blink
In learning any programming language, you often begin with some sort of `Hello, World!` program. In CircuitPython, Hello, World! is blinking an LED. Blink is one of the simplest programs in CircuitPython. Despite its simplicity, it shows you many of the basic concepts needed for most CircuitPython programs, and provides a solid basis for more complex projects. Your board has a built-in NeoPixel LED that is great this example.
A NeoPixel is what Adafruit calls the WS281x family of addressable RGB LEDs. The built-in LEDs on your board are NeoPixels! Each NeoPixel contains three LEDs - a red one, a green one and a blue one - along side a driver chip in a tiny package controlled by a single pin. They can be used individually, or chained together in strips or other creative form factors. NeoPixels do not light up on their own; they require a microcontroller. So, it's super convenient that there is a NeoPixel built in to your microcontroller board!
Time to get blinky!
## NeoPixel Location
## Blinking a NeoPixel LED
In the example below, click the **Download Project Bundle** button below to download the necessary files in a zip file. Extract the contents of the zip file, open the directory **CircuitPython\_Templates/neopixel\_blink\_one\_pixel/** and then click on the directory that matches the version of CircuitPython you're using and copy **code.py** to your **CIRCUITPY** drive.
Your **CIRCUITPY** drive should now look similar to the following image:
https://github.com/adafruit/Adafruit_Learning_System_Guides/blob/main/CircuitPython_Templates/neopixel_blink_one_pixel/code.py
The built-in NeoPixel LED begins blinking!
It's important to understand what is going on in this program.
First you `import` three modules: `time`, `board` and `neopixel`. This makes these modules and libraries available for use in your code. The first two are modules built-in to CircuitPython, so you don't need to download anything to use those. The `neopixel` library is separate, which is why you needed to install it before getting started.
Next, you set up the NeoPixel LED. To interact with hardware in CircuitPython, your code must let the board know where to look for the hardware and what to do with it. So, you create a `neopixel.NeoPixel()` object, provide it the NeoPixel LED pin using the `board` module, and tell it the number of LEDs. You save this object to the variable `pixel`.
Finally, you create a `while True:` loop. This means all the code inside the loop will repeat indefinitely. Inside the loop, you "fill" the pixel with red using the RGB tuple `(255, 0, 0)`. (For more information on how RGB tuples work, see the next section!) Then, you use `time.sleep(0.5)` to tell the code to wait half a second before moving on to the next line. The next fills the pixel with "black", which turns it off. Then you use another `time.sleep(0.5)` to wait half a second before starting the loop over again.
With only a small update, you can control the blink speed. The blink speed is controlled by the amount of time you tell the code to wait before moving on using `time.sleep()`. The example uses `0.5`, which is one half of one second. Try increasing or decreasing these values to see how the blinking changes.
That's all there is to blinking a built-in NeoPixel LED using CircuitPython!
## RGB LED Colors
RGB LED colors are set using a combination of **r** ed, **g** reen, and **b** lue, in the form of an ( **R** , **G** , **B** ) tuple. Each member of the tuple is set to a number between 0 and 255 that determines the amount of each color present. Red, green and blue in different combinations can create all the colors in the rainbow! So, for example, to set an LED to red, the tuple would be (255, 0, 0), which has the maximum level of red, and no green or blue. Green would be (0, 255, 0), etc. For the colors between, you set a combination, such as cyan which is (0, 255, 255), with equal amounts of green and blue. If you increase all values to the same level, you get white! If you decrease all the values to 0, you turn the LED off.
Common colors include:
- red: (255, 0, 0)
- green: (0, 255, 0)
- blue: (0, 0, 255)
- cyan: (0, 255, 255)
- purple: (255, 0, 255)
- yellow: (255, 255, 0)
- white: (255, 255, 255)
- black (off): (0, 0, 0)
# Adafruit TRRS Trinkey
## I2C
The **I2C** , or [inter-integrated circuit](https://en.wikipedia.org/wiki/I%C2%B2C), is a 2-wire protocol for communicating with simple sensors and devices, which means it uses two connections, or wires, for transmitting and receiving data. One connection is a clock, called **SCL**. The other is the data line, called **SDA**. Each pair of clock and data pins are referred to as a **bus**.
Typically, there is a device that acts as a **controller** and sends requests to the **target** devices on each bus. In this case, your microcontroller board acts as the controller, and the sensor breakout acts as the target. Historically, the controller is referred to as the master, and the target is referred to as the slave, so you may run into that terminology elsewhere. The official terminology is [controller and target](https://adafruit.com/controller-peripheral).
**Multiple I2C devices can be connected to the same clock and data lines.** Each I2C device has an address, and as long as the addresses are different, you can connect them at the same time. This means you can have many different sensors and devices all connected to the same two pins.
**Both I2C connections require pull-up resistors** , and most Adafruit I2C sensors and breakouts have pull-up resistors built in. If you're using one that does not, you'll need to add your own 2.2-10kΩ pull-up resistors from SCL and SDA to 3.3V.
## I2C and CircuitPython
CircuitPython supports many I2C devices, and makes it super simple to interact with them. There are libraries available for many I2C devices in the [CircuitPython Library Bundle](https://circuitpython.readthedocs.io/projects/bundle/en/latest/#table-of-contents). (If you don't see the sensor you're looking for, keep checking back, more are being written all the time!)
In this section, you'll learn how to scan the I2C bus for all connected devices. Then you'll learn how to interact with an I2C device.
## Necessary Hardware
You'll need the following additional hardware to complete the examples on this page.
### Adafruit MCP9808 High Accuracy I2C Temperature Sensor Breakout
[Adafruit MCP9808 High Accuracy I2C Temperature Sensor Breakout](https://www.adafruit.com/product/5027)
The MCP9808 digital temperature sensor is one of the more accurate/precise we've ever seen, with a typical accuracy of ±0.25°C over the sensor's -40°C to +125°C range and precision of +0.0625°C. They work great with any microcontroller using standard I2C. With...
Out of Stock
[Buy Now](https://www.adafruit.com/product/5027)
[Related Guides to the Product](https://learn.adafruit.com/products/5027/guides)
### STEMMA QT / Qwiic JST SH 4-Pin Cable - 50mm Long
[STEMMA QT / Qwiic JST SH 4-Pin Cable - 50mm Long](https://www.adafruit.com/product/4399)
This 4-wire cable is 50mm / 1.9" long and fitted with JST SH female 4-pin connectors on both ends. Compared with the chunkier JST PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove.
In Stock
[Buy Now](https://www.adafruit.com/product/4399)
[Related Guides to the Product](https://learn.adafruit.com/products/4399/guides)
While the examples here will be using the [Adafruit MCP9808](https://www.adafruit.com/product/5027), a high accuracy temperature sensor, the overall process is the same for just about any I2C sensor or device.
The first thing you'll want to do is get the sensor connected so your board has I2C to talk to.
## Wiring the MCP9808
The MCP9808 comes with a STEMMA QT connector, which makes wiring it up quite simple and solder-free.
Connect the STEMMA QT cable from **the STEMMA QT port on your board** to **the STEMMA QT port on the MCP9808**.
## Find Your Sensor
The first thing you'll want to do after getting the sensor wired up, is make sure it's wired correctly. You're going to do an I2C scan to see if the board is detected, and if it is, print out its I2C address.
Save the following to your **CIRCUITPY** drive as **code.py**.
Click the **Download Project Bundle** button below to download the necessary libraries and the **code.py** file in a zip file. Extract the contents of the zip file, find your CircuitPython version, and copy the matching **code.py** file to your **CIRCUITPY** drive.
Your **CIRCUITPY** drive should now look similar to the following image:
https://github.com/adafruit/Adafruit_Learning_System_Guides/blob/main/CircuitPython_Templates/i2c_scan/code.py
If you run this and it seems to hang, try manually unlocking your I2C bus by running the following two commands from the REPL.
```terminal
import board
board.I2C().unlock()
```
First you create the `i2c` object, using `board.I2C()`. This convenience routine creates and saves a `busio.I2C` object using the default pins `board.SCL` and `board.SDA`. If the object has already been created, then the existing object is returned. No matter how many times you call `board.I2C()`, it will return the same object. This is called a _singleton_.
To be able to scan it, you need to lock the I2C down so the only thing accessing it is the code. So next you include a loop that waits until I2C is locked and then continues on to the scan function.
Last, you have the loop that runs the actual scan, `i2c_scan()`. Because I2C typically refers to addresses in hex form, the example includes this bit of code that formats the results into hex format: `[hex(device_address) for device_address in i2c.scan()]`.
Open the serial console to see the results! The code prints out an array of addresses. You've connected the MCP9808 which has a 7-bit I2C address of 0x18. The result for this sensor is `I2C addresses found: ['0x18']`. If no addresses are returned, refer back to the wiring diagrams to make sure you've wired up your sensor correctly.
## I2C Sensor Data
Now you know for certain that your sensor is connected and ready to go. Time to find out how to get the data from the sensor!
Save the following to your **CIRCUITPY** drive as **code.py**.
Click the **Download Project Bundle** button below to download the necessary libraries and the **code.py** file in a zip file. Extract the contents of the zip file, find your CircuitPython version, and copy the matching **entire** **lib** **folder** and **code.py** file to your **CIRCUITPY** drive.
Your **CIRCUITPY** drive should now look similar to the following image:
https://github.com/adafruit/Adafruit_Learning_System_Guides/blob/main/CircuitPython_Templates/i2c_mcp9808/code.py
This code begins the same way as the scan code, except this time, you create your sensor object using the sensor library. You call it `mcp9808` and provide it the `i2c` object.
Then you have a simple loop that prints out the temperature reading using the sensor object you created. Finally, there's a `time.sleep(2)`, so it only prints once every two seconds. Connect to the serial console to see the results. Try touching the MCP9808 with your finger to see the values change!
## Where's my I2C?
On many microcontrollers, you have the flexibility of using a wide range of pins for I2C. On some types of microcontrollers, any pin can be used for I2C! Other chips require using bitbangio, but can also use any pins for I2C. There are further microcontrollers that may have fixed I2C pins.
Given the many different types of microcontroller boards available, it's impossible to guarantee anything other than the labeled 'SDA' and 'SCL' pins. So, if you want some other setup, or multiple I2C interfaces, how will you find those pins? Easy! Below is a handy script.
Save the following to your **CIRCUITPY** drive as **code.py**.
Click the **Download Project Bundle** button below to download the necessary libraries and the **code.py** file in a zip file. Extract the contents of the zip file, find your CircuitPython version, and copy the matching **code.py** file to your **CIRCUITPY** drive.
Your **CIRCUITPY** drive should now look similar to the following image:
https://github.com/adafruit/Adafruit_Learning_System_Guides/blob/main/CircuitPython_Templates/i2c_find_pins/code.py
Now, connect to the serial console and check out the output! The results print out a nice handy list of SCL and SDA pin pairs that support I2C.
Info:
# Adafruit TRRS Trinkey
## CircuitPython AT Switch Example
The main use case for this Trinkey is to use it for making AT devices. CircuitPython has excellent [HID device support](https://docs.circuitpython.org/projects/hid/en/latest/) that lets you write Python code to build HID devices. In the example below, you'll attach two switches to the TRRS jack to send HID commands. The example is sending keyboard presses, but you can also send mouse operations, or do both.
### 3.5mm (1/8") Stereo Audio Plug Terminal Block
[3.5mm (1/8") Stereo Audio Plug Terminal Block](https://www.adafruit.com/product/2790)
One truth about working with audio is you always need the cable or adapter you _don't_ have in your toolbox. That's why we love these terminal-block audio connectors so much. **No soldering required!** Use stranded or solid core wire and a small screw driver to...
In Stock
[Buy Now](https://www.adafruit.com/product/2790)
[Related Guides to the Product](https://learn.adafruit.com/products/2790/guides)
## TRRS Standards
If you are using a TRRS splitter instead of an audio plug terminal block, it's important to keep in mind that there are [two main standards for TRRS](https://en.wikipedia.org/wiki/Phone_connector_(audio)#TRRS_standards): CTIA and OMTP. If you're familiar with [TRS-A and TRS-B MIDI standards](https://minimidi.world/), then you'll know how 3.5 mm jacks can be tricky. The pin definitions for your TRRS Trinkey may vary depending on the type of adapter or cable you are using.
## Wiring
- **Trinkey TIP (left audio)** to **button 1 output (blue wire)**
- **Trinkey RING\_1 (right audio)** to **button 2 output (green wire)**
- **Trinkey SLEEVE** to **button 1 GND (black wire)**
- **Trinkey SLEEVE** to **button 2 GND (black wire)**
## CircuitPython Usage
To use with CircuitPython, you need to first install the HID library into the **lib** folder onto your **CIRCUITPY** drive. Then you need to update **code.py** with the example script.
Thankfully, we can do this in one go. In the example below, click the **Download Project Bundle** button below to download the necessary libraries and the **code.py** file in a zip file. Extract the contents of the zip file, and copy the **entire lib folder** and the **code.py** file to your **CIRCUITPY** drive.
Your **CIRCUITPY/lib** folder should contain the following folder:
- **adafruit\_hid/**
## Example Code
Once everything is saved to the **CIRCUITPY** drive, [connect to the serial console](https://learn.adafruit.com/welcome-to-circuitpython/kattni-connecting-to-the-serial-console) to see the data printed out!
https://github.com/adafruit/Adafruit_Learning_System_Guides/blob/main/TRRS_Trinkey_Demos/CircuitPython_AT_Demo/code.py
In the code, the direction of the TRRS pins are changed to switch between plug detection and inputs. When you insert a cable, you'll see "`inserted!`" print to the serial console. When **TIP** is tied to ground ( **SLEEVE** ), you'll see "`A`" print to the serial console. You'll also send an A keycode over HID. When **RING\_1** is tied to ground ( **SLEEVE** ), you'll see "`B`" print to the serial console. You'll also send a B keycode over HID.
# Adafruit TRRS Trinkey
## Two Switch Scanning
"Two Switch Scanning" is a technique used in Assistive Technology where the user will use a two switches to jump between options and activate the option they'd like. Often, the switches are called "Next" and "Select", but this is an approach that should seem familiar to most web users: it's basically the equivalent of using the Tab key to find the button you want and then the Enter key to activate it.
The approach is commonly used in operating systems like iOS, Android and MacOS (Windows has yet to add switch support!), and is supported by all of the major Speech Generating Devices (SGDs) including Open Source tools like WeaveChat and CoughDrop as well as pricier commercial offerings like TouchChat and LAMP from PRC, and Snap+Core from Tobii.
With the TRRS Trinkey, we can access all of that Two Switch Scanning goodness without having to have a dedicated device or buy an expensive Switch Interface! Let's see how!
https://www.youtube.com/watch?v=2ACPVzMF_Uo
## Parts
### Part: Adafruit TRRS Trinkey
quantity: 1
Allows us to create custom adapters for any AT switch needs
[Adafruit TRRS Trinkey](https://www.adafruit.com/product/5954)
### Part: 3.5mm Stereo to Mono Adapter
quantity: 1
This simple Stereo to Mono adapter available at Amazon or other retailers will split out the TRRS jack into two TS jacks for two standard AT Switches to use
[3.5mm Stereo to Mono Adapter](https://www.amazon.com/dp/B096XNHTH3?psc=1&ref=ppx_yo2ov_dt_b_product_details)
### Part: Logitech Adaptive Gaming Kit
quantity: 1
This kit contains 10 standard AT Switches plus lots of accessories - it's a great deal, and we only need to two of the switches for this project
[Logitech Adaptive Gaming Kit](https://www.logitechg.com/en-us/products/gamepads/adaptive-gaming-kit-accessories.943-000318.html)
### Part: USB C On-The-Go Adapter
quantity: 1
Optional: Allows you to connect to your Android, iPad, or the latest iPhones
[USB C On-The-Go Adapter](https://www.amazon.com/dp/B07BS8SRWH?psc=1&ref=ppx_yo2ov_dt_b_product_details)
### Part: Lightning On-The-Go Adapter
quantity: 1
Optional: Allows you to connect to your iPhones and older iPads.
[Lightning On-The-Go Adapter](https://www.amazon.com/Lightning-Adapter-Support-Connect-Keyboard/dp/B08R63KFP3/ref=sr_1_4?crid=3C49D2SD6KUE9&dib=eyJ2IjoiMSJ9.hIoRurVr8s2CdIqIBcCnpf5MvJrqegrisOkPiGWBE5rF1LvS3bMlIum-DrK9uvjSQ8lXvmO-jMCdgWyEvUVX4tZG9Os3ZHSWOJ2ambawMJlow9Xmz3NXH6U4vz3Wq8oBNlbJPOr8O3UIRe6-wWfH1hctU3Dlhd_hDUsQ2kvjZwNrNaeGkR1y3o3fMne4IOWjZiIMT6L-5fq4osG3_TTvKWqdsTIgmgCRBrCI5VxbT0wYYppoOxtsFy77Ax9J7sVqYrrZeZgz6d32B1nF43eWR6xMTZAJVo1V8-DiCq3on4w.X5Eap8mL6yVdA6d2mzsGMHDlVOGS56i4iqpZKBrL9yc&dib_tag=se&keywords=lightning%2Botg&qid=1716946254&s=electronics&sprefix=lightning%2Botg%2Celectronics%2C103&sr=1-4&th=1)
## Assembly
Assembly couldn't be simpler: just connect the wires between the components - no soldering needed!
1. Connect your "Next" switch (labeled B here) to the Red jack on the Stereo splitter
2. Connect your "Select" switch (labeled A here) to the White jack on the Stereo Splitter
3. Connect the TRS Stereo end of the splitter to the TRRS Trinkey's 3.5mm jack
4. [Optional] Connect the USB A plug of the TRRS Trinkey to a USB C or Lightning OTG adapter (if using a tablet or phone)
5. Connect the OTG Adapter (or the USB A plug if no adapter is used) into your PC/Mac/phone/tablet.
## CircuitPython Usage
To use with CircuitPython, you need to first install the HID library into the **lib** folder onto your **CIRCUITPY** drive. Then you need to update **code.py** with the example script.
Thankfully, we can do this in one go. In the example below, click the **Download Project Bundle** button below to download the necessary libraries and the **code.py** file in a zip file. Extract the contents of the zip file, and copy the **entire lib folder** and the **code.py** file to your **CIRCUITPY** drive.
https://github.com/adafruit/Adafruit_Learning_System_Guides/blob/main/TRRS_Trinkey_Demos/CircuitPython_Two_Switch_Keyboard/code.py
Our CircuitPython code is **very** similar to the "AT Switch Example" from the previous section. It sends two keycodes (by default "A" and "B") as an HID Keyboard when the two AT Switches are pressed. We add three important details to make things work a bit smoother with AT systems:
1. We use the **keypad** library to handle debouncing, pullup management and state management for us.
2. We've restructured the code to send "press" and "release" HID messages when the user presses and releases the switches. This allows for systems like iOS that support "long press" vs. "short press" to work
3. We've omitted the insertion detection for clarity - but it can be added back as an exercise for the reader
## Configure iOS Switch Control
Configuring Switch Control on iOS or iPadOS is beyond the scope of this guide: luckily, our friend, Chris Young, wrote a full Guide on the subject! Check out [this section which details how to configure Switch Control](https://learn.adafruit.com/ios-switch-control-using-ble/configuring-ios-switch-control "iOS Switch Control").
Remember, you'll be using the USB switches instead of the Bluetooth options, so you can skip the pairing process. Otherwise, all the steps and features apply.
## Using iOS Switch Control
Now, your iPhone or iPad can be controlled with just two switches. You can type, activate buttons, even using a "gliding cursor" to grab and move items around the screen! You can configure each button to have different actions for "short" and "long" presses, you can even write macros and "recipes" to automate your actions.
For a great example of what a **pro** can do using switch control, check out [Todd Stabelfeldt](https://www.youtube.com/@ToddStabelfeldt)'s amazing YouTube video clip:
https://www.youtube.com/watch?v=kj9UodcwIes
## Speech Generating Devices
Unfortunately, Speech Generating Devices (SGDs) and the software that runs on them is notoriously expensive. So, there's not a great way to demonstrate that for you, other than to demonstrate the device on CoughDrop (which **used** to be Open Source) in the video above and to assure you that all of the major Speech Software systems support two switch scanning and will work with a keyboard-style switch interface like ours.
Here's some videos to help with a few popular SGD software systems:
- Setting up [Scanning In CoughDrop](https://www.youtube.com/watch?v=4bf6uTJ7T5E)
- [LAMP Word For Life Scanning Settings](https://youtu.be/SP-PhSylGMo?si=_lNjrj22G-vnBQ3M&t=1050)
- All about [Scanning in Tobii Snap+Core](https://www.youtube.com/playlist?list=PLs_sIekvATdwnm83-gT5jkJOvrbXTevEC)
# Adafruit TRRS Trinkey
## Adaptive Joysticks
The Xbox Adaptive Controller (XAC) has two USB ports on the side for use with USB joysticks -- these are designed to allow alternative hardware to replace the left and right thumbsticks of a typical gaming controller. Rather than be constrained by the commercially available USB joysticks, you can use the TRRS Trinkey to design custom solutions.
In this example, a typical X/Y dual potentiometer joystick breakout is read by two analog pins on the TRRS Trinkey. The Trinkey is running CircuitPython and emulating an XAC-compatible HID gamepad. You can substitute your own analog inputs, such as joystick/thumbstick modules, soft potentiometers, and more, as well as adjust the code to meet your needs.
### Adafruit TRRS Trinkey - USB Key for Assistive Technology
[Adafruit TRRS Trinkey - USB Key for Assistive Technology](https://www.adafruit.com/product/5954)
It's half USB Key, half TRRS breakout_... _it's the **Adafruit TRRS Trinkey** specifically designed for Assistive Technology hackers and creators as a simple and low cost, but also flexible and extendable AT device.
Many AT interface...
In Stock
[Buy Now](https://www.adafruit.com/product/5954)
[Related Guides to the Product](https://learn.adafruit.com/products/5954/guides)
### Analog 2-axis Thumb Joystick with Select Button + Breakout Board
[Analog 2-axis Thumb Joystick with Select Button + Breakout Board](https://www.adafruit.com/product/512)
This mini-kit makes it easy to mount a PSP/Xbox-like thumb joystick to your project. The thumbstick is an analog joystick - more accurate and sensitive than just 'directional' joysticks - with a 'press in to select' button. Since it's analog, you'll need two analog...
In Stock
[Buy Now](https://www.adafruit.com/product/512)
[Related Guides to the Product](https://learn.adafruit.com/products/512/guides)
### A/V and RCA (Composite Video, Audio) Cable for Raspberry Pi
[A/V and RCA (Composite Video, Audio) Cable for Raspberry Pi](https://www.adafruit.com/product/2881)
This A/V RCA Cable for Raspberry Pi is a great way to turn your Pi 3, 2, A+ or B+'s output into a full on composite video and audio device. Simply connect the cable to your Raspberry Pi's 3.5mm jack and the other side into whatever device you're looking to connect to and get...
Out of Stock
[Buy Now](https://www.adafruit.com/product/2881)
[Related Guides to the Product](https://learn.adafruit.com/products/2881/guides)
### Mini Analog Joystick - 10K Potentiometers
[Mini Analog Joystick - 10K Potentiometers](https://www.adafruit.com/product/3102)
Sometimes a simple analog control device can be the perfect tactile solution for your project, but they can be surprisingly hard to come by. Luckily we've found a low-cost, quality **Mini Analog Joystick** to fill your directional analog input needs!
Unlike most...
In Stock
[Buy Now](https://www.adafruit.com/product/3102)
[Related Guides to the Product](https://learn.adafruit.com/products/3102/guides)
### Adafruit Swirly Aluminum Mounting Grid for 0.1" Spaced PCBs
[Adafruit Swirly Aluminum Mounting Grid for 0.1" Spaced PCBs](https://www.adafruit.com/product/5774)
With most of our dev boards, sensors and feathers now sporting [plug-and-play stemma QT ports](https://learn.adafruit.com/search?q=stemma%2520qt) it can be very fast to put together projects with half a dozen boards snapped together. But that ease of use has one...
In Stock
[Buy Now](https://www.adafruit.com/product/5774)
[Related Guides to the Product](https://learn.adafruit.com/products/5774/guides)
## Assembly
## Wiring
Any of the four TRRS pins of the TRRS Trinkey can be assigned as digital in/out or analog in. We'll set the **TIP** and **RING\_1** as **analog inputs** to read the two joystick pots, and **RING\_2** and **SLEEVE** as **ground** and **Vcc** respectively.
## Cable Wiring
Use a multimeter's continuity tester to check the wire mapping of your TRRS cable (I used a TRRS to AV cable with the RCA jacks cut off, although you can also [buy them pre-cut](https://www.amazon.com/sovunis-12-5inch-Replacement-Headphone-Microphone/dp/B0CR7WTVWP/ref=sr_1_4) usually sold as "replacement 3.5mm TRRS cables"), then solder the following:
- Cable **TIP** to **Xout**
- Cable **RING\_1** to **Yout**
- Cable **RING\_2** to **GND**
- Cable **SLEEVE** to **Vcc**
## Plug In Joystick
Plug in the joystick to the TRRS Trinkey.
## CircuitPython Usage
To use with CircuitPython, you need to first install the **xac\_gamepad** library and **XACsettings.py** into the **lib** folder onto your **CIRCUITPY** drive. Then you need to update **code.py** with the example script, and save the **boot.py** onto the root of the **CIRCUITPY** drive.
Thankfully, we can do this in one go. In the example below, click the **Download Project Bundle** button below to download the necessary libraries and files in a zip file. Extract the contents of the zip file, and copy the **entire lib folder** and the **code.py** and **boot.py** files to your **CIRCUITPY** drive.
https://github.com/adafruit/Adafruit_Learning_System_Guides/blob/main/TRRS_Trinkey_Demos/XAC_Joystick/code.py
## Use It
Once you've coded the TRRS Trinkey you can plug it into either USB A port on the XAC and use it for gameplay on your Xbox or Windows machine. It will show up as either thumbstick in-game. Build a second one for the other stick if you like.
You can see it in action here:
https://www.youtube.com/live/LFN6fUiST5Q?feature=shared&t=3285
# Adafruit TRRS Trinkey
## Arduino IDE Setup
The first thing you will need to do is to download the latest release of the Arduino IDE. You will need to be using **version 1.8** or higher for this guide
[Arduino IDE Download](http://www.arduino.cc/en/Main/Software)
After you have downloaded and installed **the latest version of Arduino IDE** , you will need to start the IDE and navigate to the **Preferences** menu. You can access it from the **File** menu in _Windows_ or _Linux_, or the **Arduino** menu on _OS X_.
A dialog will pop up just like the one shown below.
We will be adding a URL to the new **Additional Boards Manager URLs** option. The list of URLs is comma separated, and _you will only have to add each URL once._ New Adafruit boards and updates to existing boards will automatically be picked up by the Board Manager each time it is opened. The URLs point to index files that the Board Manager uses to build the list of available & installed boards.
To find the most up to date list of URLs you can add, you can visit the list of [third party board URLs on the Arduino IDE wiki](https://github.com/arduino/Arduino/wiki/Unofficial-list-of-3rd-party-boards-support-urls#list-of-3rd-party-boards-support-urls). We will only need to add one URL to the IDE in this example, but _ **you can add multiple URLS by separating them with commas** _. Copy and paste the link below into the **Additional Boards Manager URLs** option in the Arduino IDE preferences.
### `https://adafruit.github.io/arduino-board-index/package_adafruit_index.json`
Here's a short description of each of the Adafruit supplied packages that will be available in the Board Manager when you add the URL:
- **Adafruit AVR Boards** - Includes support for Flora, Gemma, Feather 32u4, ItsyBitsy 32u4, Trinket, & Trinket Pro.
- **Adafruit SAMD Boards** - Includes support for Feather M0 and M4, Metro M0 and M4, ItsyBitsy M0 and M4, Circuit Playground Express, Gemma M0 and Trinket M0
- **Arduino Leonardo & Micro MIDI-USB** - This adds MIDI over USB support for the Flora, Feather 32u4, Micro and Leonardo using the [arcore project](https://github.com/rkistner/arcore).
If you have multiple boards you want to support, say ESP8266 and Adafruit, have both URLs in the text box separated by a comma (,)
Once done click **OK** to save the new preference settings. Next we will look at installing boards with the Board Manager.
Now continue to the next step to actually install the board support package!
# Adafruit TRRS Trinkey
## Using with Arduino IDE
The TRRS Trinkey uses an ATSAMD21 chip, and you can pretty easily get it working with the Arduino IDE.
Now that you have added the appropriate URLs to the Arduino IDE preferences in the previous page, you can open the **Boards Manager** by navigating to the **Tools-\>Board** menu.
Once the Board Manager opens, click on the category drop down menu on the top left hand side of the window and select **All**. You will then be able to select and install the boards supplied by the URLs added to the preferences.
Warning: Remember you need SETUP the Arduino IDE to support our board packages - see the previous page on how to add Adafruit's URL to the preferences
## Install SAMD Support
First up, install the latest **Arduino SAMD Boards** (version **1.6.11 ** or later)
You can type **Arduino SAMD** in the top search bar, then when you see the entry, click **Install**
## Install Adafruit SAMD
Next you can install the Adafruit SAMD package to add the board file definitions
Make sure you have **Type All** selected to the left of the _Filter your search..._ box
You can type **Adafruit SAMD** in the top search bar, then when you see the entry, click **Install**
Even though in theory you don't need to - I recommend rebooting the IDE
**Quit and reopen the Arduino IDE** to ensure that all of the boards are properly installed. You should now be able to select and upload to the new boards listed in the **Tools-\>Board** menu.
Select the **Adafruit TRRS Trinkey M0 (SAMD21)**.
## Install Drivers (Windows 7 & 8 Only)
When you plug in the board, you'll need to possibly install a driver
Click below to download our Driver Installer
[Download Latest Adafruit Drivers package](https://github.com/adafruit/Adafruit_Windows_Drivers/releases)
Download and run the installer
Run the installer! Since we bundle the SiLabs and FTDI drivers as well, you'll need to click through the license
Select which drivers you want to install, the defaults will set you up with just about every Adafruit board!
Click **Install** to do the installin'
## Compilation Issues
If you get an alert that looks like
**Cannot run program "{runtime.tools.arm-none-eabi-gcc.path}\bin\arm-non-eabi-g++"**
Make sure you have installed the **Arduino SAMD** boards package, you need _both_ Arduino & Adafruit SAMD board packages
## Manually bootloading
If you ever get in a 'weird' spot with the bootloader, or you have uploaded code that crashes and doesn't auto-reboot into the bootloader, click the **RST** button **twice** (like a double-click)to get back into the bootloader.
**The red LED will pulse and/or RGB LED will be green, so you know that its in bootloader mode.**
Once it is in bootloader mode, you can select the newly created COM/Serial port and re-try uploading.
You may need to go back and reselect the 'normal' USB serial port next time you want to use the normal upload.
## Ubuntu & Linux Issue Fix
[Follow the steps for installing Adafruit's udev rules on this page.](../../../../adafruit-arduino-ide-setup/linux-setup#udev-rules)
# Adafruit TRRS Trinkey
## NeoPixel Blink
The first and most basic program you can upload to your Arduino is the classic Blink sketch. This takes something on the board and makes it, well, blink! On and off. It's a great way to make sure everything is working and you're uploading your sketch to the right board and right configuration.
When all else fails, you can always come back to Blink!
Now _traditionally_ you would use an onboard LED to make a blink occur. **However, this board does not have an onboard single-color LED** , so we will 'mimic' the same blink sketch but instead of using a digital output pin, we will use NeoPixel support to blink the onboard RGB LED!
# Pre-Flight Check: Get Arduino IDE & Hardware Set Up
This lesson assumes you have Arduino IDE set up. This is a generalized checklist, some elements may not apply to your hardware. If you haven't yet, check the previous steps in the guide to make sure you:
- **Install the very latest Arduino IDE for Desktop** (not all boards are supported by the Web IDE so we don't recommend it)
- **Install any board support packages (BSP) required for your hardware.** Some boards are built in defaults on the IDE, but lots are not! You may need to install plug-in support which is called the BSP.
- **Get a Data/Sync USB cable for connecting your hardware.** A _significant_ amount of problems folks have stem from not having a USB cable with data pins. Yes, these cursed cables roam the land, making your life hard. If you find a USB cable that doesn't work for data/sync, _throw it away immediately_! There is no need to keep it around, cables are very inexpensive these days.
- **Install any drivers required** - If you have a board with a FTDI or CP210x chip, you may need to get separate drivers. If your board has native USB, it probably doesn't need anything. After installing, reboot to make sure the driver sinks in.
- **Connect the board to your computer.** If your board has a power LED, make sure its lit. Is there a power switch? Make sure its turned On!
# Start up Arduino IDE and Select Board/Port
OK, now you are prepared! Open the Arduino IDE on your computer. Now you have to tell the IDE what board you are using, and how you want to connect to it.
In the IDE find the **Tools** menu. You will use this to select the board. If you switch boards, you _must switch the selection!_ So always double-check before you upload code in a new session.
# Install NeoPixel Library
Despite their popularity, NeoPixel RGB LEDs are not supported 'out of the box' in Arduino IDE! You will need to add support by installing the library. Good news it is _very easy_ to do it. Go to the **Library Manager** here
Search for and install the **Adafruit NeoPixel** library. It might not be first in the list so make sure you get the name matched up right!
# New NeoPixel Blink Sketch
OK lets make a new blink sketch! From the **File** menu, select **New**
Then in the new window, copy and paste this text:
https://github.com/adafruit/Adafruit_Learning_System_Guides/blob/main/SHT4x_Trinkey_Demos/Arduino/trinkey_neopixel_blink/trinkey_neopixel_blink.ino
Info:
One note you'll see is that we reference the LED with the constant `PIN_NEOPIXEL` rather than a number. That's because each board could have the built in NeoPixels on a different pin and this makes the code a little more portable!
# Verify (Compile) Sketch
OK now you can click the Verify button to convert the sketch into binary data to be uploaded to the board.
Note that Verifying a sketch is the same as Compiling a sketch - so these terms will be used interchangeably.
During verification/compilation, the computer will do a bunch of work to collect all the libraries and code and the results will appear in the bottom window of the IDE.
If something went wrong with compilation, you will get red warning/error text in the bottom window letting you know what the error was. It will also highlight the line with an error.
For example, here I had the wrong board selected - and the selected board does not have a built-in NeoPixel pin defined!
Here's another common error, in my haste I forgot to add a `;` at the end of a line. The compiler warns me that it's looking for one - note that the error is actually a few lines up!
Info:
On success you will see something like this white text output and the message **Done compiling.** in the message area.
# Upload Sketch
Once the code is verified/compiling cleanly you can upload it to your board. Click the **Upload** button:
The IDE will try to compile the sketch again for good measure, then it will try to connect to the board and upload a the file.
**This is actually one of the hardest parts for beginners because it's where a lot of things can go wrong.**
However, start with what it looks like: success! Here's what your board upload process looks like when it goes right:
Often times you will get a warning like this, which is kind of vague:
`No device found on COM66` (or whatever port is selected)
`An error occurred while uploading the sketch```
This could be a few things.
**First up, check again that you have the correct board selected!** Many electronics boards have very similar names or look, and often times folks grab a board different from what they thought.
If you're positive the right board is selected, we recommend the next step is to put the board into manual bootloading mode.
## Native USB and manual bootloading
Historically, microcontroller boards contained two chips: the main micro chip (say, ATmega328 or ESP8266 or ESP32) and a separate chip for USB interface that would be used for bootloading (a CH430, FT232, CP210x, etc). With these older designs, the microcontroller is put into a bootloading state for uploading code by the separate chip. It allows for easier uploading but is more expensive as two chips are needed, and also the microcontroller can't act like a keyboard or disk drive.
Modern chips often have 'native' USB - that means that there is no separate chip for USB interface. It's all in one! Great for cost savings, simplicity of design, reduced size and more control. However, it means the chip must be self-aware enough to be able to put _itself_ into bootload/upload mode on its own. That's fine 99% of the time but is very likely you will at some point get the board into an odd state that makes it too confused to bootload.
Warning:
Before continuing we _really really_ suggest turning on **Verbose Upload** messages, it will help in this process because you will be able to see what the IDE is trying to do. It's a checkbox in the **Preferences** menu.
## Enter Manual Bootload Mode
OK now you know it's probably time to try manual bootloading. No problem! Here is how you do that for this board:
Double-click the **reset ** button, and you will see the **NeoPixel**** **turn green.
Once you are in manual bootload mode, go to the Tools menu, and make sure you have selected the bootloader serial port. **It is almost certain that the serial port has changed now that the bootloader is enabled.**
Now you can try uploading again!
Info:
This time, you should have success!
After uploading this way, be sure to **click the reset button** - it sort of makes sure that the board got a good reset and will come back to life nicely.
Warning:
It's also a good idea to try to re-upload the sketch again now that you've performed a manual bootload to get the chip into a good state. It should perform an auto-reset the second time, so you don't have to manually bootload again.
# Finally, a Blink!
OK it was a journey but now we're here and you can enjoy your blinking LED. Next up, try to change the delay between blinks and re-upload. It's a good way to make sure your upload process is smooth and practiced.
# Adafruit TRRS Trinkey
## I2C Scan Test
A lot of sensors, displays, and devices can connect over I2C. I2C is a 2-wire 'bus' that allows multiple devices to all connect on one set of pins so it's very convenient for wiring!
When using your board, you'll probably want to connect up I2C devices, and it can be a little tricky the first time. The best way to debug I2C is go through a checklist and then perform an I2C scan
# Common I2C Connectivity Issues
- **Have you connected four wires (at a minimum) for each I2C device?** Power the device with whatever is the logic level of your microcontroller board (probably 3.3V), then a ground wire, and a SCL clock wire, and and a SDA data wire.
- **If you're using a STEMMA QT board - check if the power LED is lit.** It's usually a green LED to the left side of the board.
- **Does the STEMMA QT/I2C port have switchable power or pullups?** To reduce power, some boards have the ability to cut power to I2C devices or the pullup resistors. Check the documentation if you have to do something special to turn on the power or pullups.
- **If you are using a DIY I2C device, do you have pullup resistors?** Many boards do _not_ have pullup resistors built in and they are _required!_ We suggest any common 2.2K to 10K resistors. You'll need two: one each connects from SDA to positive power, and SCL to positive power. Again, positive power (a.k.a VCC, VDD or V+) is often 3.3V
- **Do you have an address collision?** You can only have _one_ board per address. So you cannot, say, connect two AHT20's to one I2C port because they have the same address and will interfere. Check the sensor or documentation for the address. Sometimes there are ways to adjust the address.
- **Does your board have multiple I2C ports?** Historically, boards only came with one. But nowadays you can have two or even three! This can help solve the "hey, but what if I want two devices with the same address" problem: just put one on each bus.
- **Are you hot-plugging devices?** I2C does _not_ support dynamic re-connection, you cannot connect and disconnect sensors as you please. They should all be connected on boot and not change. ([Only exception is if you're using a hot-plug assistant but that'll cost you](https://www.adafruit.com/product/5159)).
- **Are you keeping the total bus length reasonable?** I2C was designed for maybe 6" max length. We like to push that with plug-n-play cables, but really please keep them as short as possible! ([Only exception is if you're using an active bus extender](https://www.adafruit.com/product/4756)).
# Perform an I2C scan!
### Install TestBed Library
To scan I2C, the Adafruit TestBed library is used. This library and example just makes the scan a little easier to run because it takes care of some of the basics. You will need to add support by installing the library. Good news: it is _very easy_ to do it. Go to the **Arduino Library Manager.**
Search for **TestBed** and install the **Adafruit TestBed** library
Now open up the I2C Scan example
https://github.com/adafruit/Adafruit_Learning_System_Guides/blob/main/I2C_Scanners/arduino/i2c_scanner/i2c_scanner.ino
### Wire up I2C device
While the examples here will be using the [Adafruit MCP9808](https://www.adafruit.com/product/5027), a high accuracy temperature sensor, the overall process is the same for just about any I2C sensor or device.
The first thing you'll want to do is get the sensor connected so your board has I2C to talk to.
### Adafruit MCP9808 High Accuracy I2C Temperature Sensor Breakout
[Adafruit MCP9808 High Accuracy I2C Temperature Sensor Breakout](https://www.adafruit.com/product/5027)
The MCP9808 digital temperature sensor is one of the more accurate/precise we've ever seen, with a typical accuracy of ±0.25°C over the sensor's -40°C to +125°C range and precision of +0.0625°C. They work great with any microcontroller using standard I2C. With...
Out of Stock
[Buy Now](https://www.adafruit.com/product/5027)
[Related Guides to the Product](https://learn.adafruit.com/products/5027/guides)
### STEMMA QT / Qwiic JST SH 4-Pin Cable - 50mm Long
[STEMMA QT / Qwiic JST SH 4-Pin Cable - 50mm Long](https://www.adafruit.com/product/4399)
This 4-wire cable is 50mm / 1.9" long and fitted with JST SH female 4-pin connectors on both ends. Compared with the chunkier JST PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove.
In Stock
[Buy Now](https://www.adafruit.com/product/4399)
[Related Guides to the Product](https://learn.adafruit.com/products/4399/guides)
## Wiring the MCP9808
The MCP9808 comes with a STEMMA QT connector, which makes wiring it up quite simple and solder-free.
Now upload the scanning sketch to your microcontroller and open the serial port to see the output. You should see something like this:
# Adafruit TRRS Trinkey
## Arduino AT Switch Example
The main use case for this Trinkey is to use it for making AT devices. Using the TRRS Trinkey with Arduino involves installing the necessary libraries, wiring up two switches to the TRRS jack and running the provided example code. In the example below, you'll turn your TRRS Trinkey into an HID keyboard.
### 3.5mm (1/8") Stereo Audio Plug Terminal Block
[3.5mm (1/8") Stereo Audio Plug Terminal Block](https://www.adafruit.com/product/2790)
One truth about working with audio is you always need the cable or adapter you _don't_ have in your toolbox. That's why we love these terminal-block audio connectors so much. **No soldering required!** Use stranded or solid core wire and a small screw driver to...
In Stock
[Buy Now](https://www.adafruit.com/product/2790)
[Related Guides to the Product](https://learn.adafruit.com/products/2790/guides)
## TRRS Standards
If you are using a TRRS splitter instead of an audio plug terminal block, it's important to keep in mind that there are [two main standards for TRRS](https://en.wikipedia.org/wiki/Phone_connector_(audio)#TRRS_standards): CTIA and OMTP. If you're familiar with [TRS-A and TRS-B MIDI standards](https://minimidi.world/), then you'll know how 3.5 mm jacks can be tricky. The pin definitions for your TRRS Trinkey may vary depending on the type of adapter or cable you are using.
## Wiring
- **Trinkey TIP (left audio)** to **button 1 output (blue wire)**
- **Trinkey RING\_1 (right audio)** to **button 2 output (green wire)**
- **Trinkey SLEEVE** to **button 1 GND (black wire)**
- **Trinkey SLEEVE** to **button 2 GND (black wire)**
## Library Installation
You can install the **Adafruit TinyUSB** library for Arduino using the Library Manager in the Arduino IDE.
Click the **Manage Libraries ...** menu item, search for **Adafruit TinyUSB** and select the **Adafruit TinyUSB** library:
If asked about dependencies for any of the libraries, click "Install all".
If the "Dependencies" window does not come up, then you already have the dependencies installed.
Warning: If the dependencies are already installed, you must make sure you update them through the Arduino Library Manager before loading the example!
## Example Code
https://github.com/adafruit/Adafruit_Learning_System_Guides/blob/main/TRRS_Trinkey_Demos/TRRS_Trinkey_AT_Demo/TRRS_Trinkey_AT_Demo.ino
Upload the sketch to your board and open up the Serial Monitor ( **Tools -\> Serial Monitor** ) at 115200 baud. You'll see "`inserted!`" print to the Serial Monitor when you insert a cable into the TRRS port. When **TIP** is tied to ground ( **SLEEVE** ), you'll send an A keycode over HID. When **RING\_1** is tied to ground ( **SLEEVE** ), you'll send a B keycode over HID.
# Adafruit TRRS Trinkey
## Downloads
## Files
- [ATSAMD21 Datasheet](https://cdn-learn.adafruit.com/assets/assets/000/128/998/original/SAM_D21_DA1_Family_DataSheet_DS40001882F.pdf?1711482901)
- [Webpage for the ATSAMD21E18 (main chip used)](http://www.microchip.com/wwwproducts/en/ATSAMD21E18)
- [EagleCAD PCB files on GitHub](https://github.com/adafruit/Adafruit-TRRS-Trinkey-PCB)
- [Factory Demo .UF2 File](https://github.com/adafruit/Adafruit-TRRS-Trinkey-PCB/raw/main/factory-reset/Adafruit-TRRS-Trinkey-Factory-Reset.uf2)
- [Fritzing object in the Adafruit Fritzing Library](https://github.com/adafruit/Fritzing-Library/blob/master/parts/Adafruit%20TRRS%20Trinkey.fzpz)
- [PrettyPins PDF on GitHub](https://github.com/adafruit/Adafruit-TRRS-Trinkey-PCB/blob/main/Adafruit%20TRRS%20Trinkey%20PrettyPins.pdf)
[3D Printed Case files for SLA](https://cdn-learn.adafruit.com/assets/assets/000/132/533/original/SLA_STLs.zip?1727097951)
[3D Printed Case files for FDM](https://cdn-learn.adafruit.com/assets/assets/000/132/534/original/STLs.zip?1727098005)
## Schematic and Fab Print
## Primary Products
### Adafruit TRRS Trinkey - USB Key for Assistive Technology
[Adafruit TRRS Trinkey - USB Key for Assistive Technology](https://www.adafruit.com/product/5954)
It's half USB Key, half TRRS breakout_... _it's the **Adafruit TRRS Trinkey** specifically designed for Assistive Technology hackers and creators as a simple and low cost, but also flexible and extendable AT device.
Many AT interface...
In Stock
[Buy Now](https://www.adafruit.com/product/5954)
[Related Guides to the Product](https://learn.adafruit.com/products/5954/guides)
## Featured Products
### Snap-on Enclosure for Adafruit TRRS Trinkey
[Snap-on Enclosure for Adafruit TRRS Trinkey](https://www.adafruit.com/product/5981)
Here is a cute and minimal enclosure for your [TRRS Trinkey](http://www.adafruit.com/product/5954) to keep it safe during use and transport. This case has been custom designed and 3D printed to accommodate the reset button and STEMMA QT connector. No screws or glue are...
In Stock
[Buy Now](https://www.adafruit.com/product/5981)
[Related Guides to the Product](https://learn.adafruit.com/products/5981/guides)
### Clear Snap-on Enclosure for Adafruit TRRS Trinkey
[Clear Snap-on Enclosure for Adafruit TRRS Trinkey](https://www.adafruit.com/product/6015)
Here is a cute and minimal enclosure for your [TRRS Trinkey](http://www.adafruit.com/product/5954) to keep it safe during use and transport. This case has been custom-designed and 3D printed to accommodate the reset button and STEMMA QT connector. No screws or glue are...
In Stock
[Buy Now](https://www.adafruit.com/product/6015)
[Related Guides to the Product](https://learn.adafruit.com/products/6015/guides)
## Related Guides
- [Using the TRRS Trinkey as an Assistive Technology Device](https://learn.adafruit.com/using-the-trrs-trinkey-as-an-assistive-technology-device.md)
- [Adafruit I2C QT Rotary Encoder](https://learn.adafruit.com/adafruit-i2c-qt-rotary-encoder.md)
- [Adafruit Mini GPS PA1010D Module](https://learn.adafruit.com/adafruit-mini-gps-pa1010d-module.md)
- [Adafruit PCA9548 8-Channel STEMMA QT / Qwiic I2C Multiplexer](https://learn.adafruit.com/adafruit-pca9548-8-channel-stemma-qt-qwiic-i2c-multiplexer.md)
- [Adafruit LSM6DS3TR-C + LIS3MDL - Precision 9 DoF IMU](https://learn.adafruit.com/adafruit-lsm6ds3tr-c-lis3mdl-precision-9-dof-imu.md)
- [ST 9-DoF Combo Breakouts and Wings](https://learn.adafruit.com/st-9-dof-combo.md)
- [Asteroid Tracker](https://learn.adafruit.com/asteroid-tracker.md)
- [Adafruit Sensirion SHTC3 - Temperature & Humidity Sensor Breakout](https://learn.adafruit.com/adafruit-sensirion-shtc3-temperature-humidity-sensor.md)
- [CircuitPython Elgato WiFi Light Controller](https://learn.adafruit.com/circuitpython-elgato-wifi-light-controller.md)
- [Adafruit Analog Accelerometer Breakouts](https://learn.adafruit.com/adafruit-analog-accelerometer-breakouts.md)
- [Digi-Key IoT Studio Mini Smart Home](https://learn.adafruit.com/digikey-iot-studio-smart-home.md)
- [Working with I2C Devices](https://learn.adafruit.com/working-with-i2c-devices.md)
- [Adafruit ESP32-S3 Reverse TFT Feather](https://learn.adafruit.com/esp32-s3-reverse-tft-feather.md)
- [Adafruit STEMMA Speaker](https://learn.adafruit.com/adafruit-stemma-speaker.md)
- [Installing CircuitPython on SAMD21 Boards](https://learn.adafruit.com/installing-circuitpython-on-samd21-boards.md)