// SPDX-FileCopyrightText: 2023 Liz Clark for Adafruit Industries
//
// SPDX-License-Identifier: MIT
/*
  SD card read/write

 This example shows how to read and write data to and from an SD card file
 The circuit:
 * SD card attached to SPI bus as follows:
 ** MOSI - pin 11
 ** MISO - pin 12
 ** CLK - pin 13

 created   Nov 2010
 by David A. Mellis
 modified 9 Apr 2012
 by Tom Igoe
 modified 14 Feb 2023
 by Liz Clark
 modified 25 Aug 2023
 by Kattni Rembor

 This example code is in the public domain.

 */

#include <SPI.h>
#include "SdFat.h"

#define SD_CS_PIN 23

SdFat SD;
FsFile myFile;
SdSpiConfig config(SD_CS_PIN, DEDICATED_SPI, SD_SCK_MHZ(16), &SPI1);

void setup() {
  // Open serial communications and wait for port to open:
  Serial.begin(115200);
  while (!Serial) { yield(); delay(10); }     // wait till serial port is opened
  delay(100);  // RP2040 delay is not a bad idea

  Serial.print("Initializing SD card...");

  // Retry mechanism for SD card initialization
  while (!SD.begin(config)) {
    Serial.println("initialization failed! Retrying...");
    delay(1000); // Wait for a second before retrying
  }
  Serial.println("initialization done.");

  // open the file. note that only one file can be open at a time,
  // so you have to close this one before opening another.
  myFile = SD.open("test.txt", FILE_WRITE);

  // if the file opened okay, write to it:
  if (myFile) {
    Serial.print("Writing to test.txt...");
    myFile.println("testing 1, 2, 3.");
    myFile.println("hello world!");
    // close the file:
    myFile.close();
    Serial.println("done.");
  } else {
    // if the file didn't open, print an error:
    Serial.println("error opening test.txt");
  }

  // re-open the file for reading:
  myFile = SD.open("test.txt");
  if (myFile) {
    Serial.println("test.txt:");

    // read from the file until there's nothing else in it:
    while (myFile.available()) {
      Serial.write(myFile.read());
    }
    // close the file:
    myFile.close();
  } else {
    // if the file didn't open, print an error:
    Serial.println("error opening test.txt");
  }
}

void loop() {
  // nothing happens after setup
}

// SPDX-FileCopyrightText: 2023 Liz Clark for Adafruit Industries
//
// SPDX-License-Identifier: MIT
/*
  SD card read/write

 This example shows how to read and write data to and from an SD card file
 The circuit:
 * SD card attached to SPI bus as follows:
 ** MOSI - pin 11
 ** MISO - pin 12
 ** CLK - pin 13

 created   Nov 2010
 by David A. Mellis
 modified 9 Apr 2012
 by Tom Igoe
 modified 14 Feb 2023
 by Liz Clark
 modified 25 Aug 2023
 by Kattni Rembor

 This example code is in the public domain.

 */

#include <SPI.h>
#include "SdFat.h"

#define SD_CS_PIN 23

SdFat SD;
FsFile myFile;
SdSpiConfig config(SD_CS_PIN, DEDICATED_SPI, SD_SCK_MHZ(16), &SPI1);

void setup() {
  // Open serial communications and wait for port to open:
  Serial.begin(115200);
  while (!Serial) { yield(); delay(10); }     // wait till serial port is opened
  delay(100);  // RP2040 delay is not a bad idea

  Serial.print("Initializing SD card...");

  // Retry mechanism for SD card initialization
  while (!SD.begin(config)) {
    Serial.println("initialization failed! Retrying...");
    delay(1000); // Wait for a second before retrying
  }
  Serial.println("initialization done.");

  // open the file. note that only one file can be open at a time,
  // so you have to close this one before opening another.
  myFile = SD.open("test.txt", FILE_WRITE);

  // if the file opened okay, write to it:
  if (myFile) {
    Serial.print("Writing to test.txt...");
    myFile.println("testing 1, 2, 3.");
    myFile.println("hello world!");
    // close the file:
    myFile.close();
    Serial.println("done.");
  } else {
    // if the file didn't open, print an error:
    Serial.println("error opening test.txt");
  }

  // re-open the file for reading:
  myFile = SD.open("test.txt");
  if (myFile) {
    Serial.println("test.txt:");

    // read from the file until there's nothing else in it:
    while (myFile.available()) {
      Serial.write(myFile.read());
    }
    // close the file:
    myFile.close();
  } else {
    // if the file didn't open, print an error:
    Serial.println("error opening test.txt");
  }
}

void loop() {
  // nothing happens after setup
}