CircuitPython BLE UART Example
It's easy to use Adafruit AirLift ESP32 co-processor boards for Bluetooth Low Energy (BLE) with CircuitPython. When you reset the ESP32, you can put it in WiFi mode (the default), or in BLE mode; you cannot use both modes simultaneously.
Here's a simple example of using BLE to connect CircuitPython with the Bluefruit Connect app. Use CircuitPython 6.0.0 or later.
Note: Don't confuse the ESP32 with the ESP32-S2, which is a different module with a similar name. The ESP32-S2 does not support BLE.
Adafruit AirLift ESP32 Breakout Wiring
If you have an Adafruit AirLift ESP32 Breakout board, you'll need to wire it to your microcontroller board. The following example shows it wired to a Feather M4. You can choose different pins for GPIO0, BUSY, and !RST, but the pin choices below correspond to several other boards, for consistency. If you do change the pins, keeping the TX and RX pins the same is a good idea. If you choose different pins, you'll need to edit the example program below.
Update the AirLift Firmware
You will need to update the AirLift's firmware to at least version 1.7.1. Previous versions of the AirLift firmware do not support BLE.
Follow the instructions in the guide below, and come back to this page when you've upgraded the AirLift's firmware:
Install CircuitPython Libraries
First make sure you are running the latest version of Adafruit CircuitPython for your board.
Next you'll need to install the necessary libraries to use the hardware. Thankfully, we can do this in one go. In the example below, click the Download Project Bundle button below to download the necessary libraries and the code.py file in a zip file. Extract the contents of the zip file, and copy the entire lib folder and the code.py file to your CIRCUITPY drive.
Your CIRCUITPY/lib folder should contain the following folders and files:
- /adafruit_airlift
- /adafruit_ble
- /adafruit_bus_device
- /adafruit_esp32spi
- adafruit_requests.mpy
Install the Adafruit Bluefruit LE Connect App
The Adafruit Bluefruit LE Connect iOS and Android apps allow you to connect to BLE peripherals that provide a over-the-air "UART" service. Follow the instructions in the Bluefruit LE Connect Guide to download and install the app on your phone or tablet.
# SPDX-FileCopyrightText: 2020 Dan Halbert, written for Adafruit Industries # # SPDX-License-Identifier: Unlicense # pylint: disable=unused-import import board import busio from digitalio import DigitalInOut from adafruit_ble import BLERadio from adafruit_ble.advertising.standard import ProvideServicesAdvertisement from adafruit_ble.services.nordic import UARTService from adafruit_esp32spi import adafruit_esp32spi from adafruit_airlift.esp32 import ESP32 # If you are using a Metro M4 Airlift Lite, PyPortal, # or MatrixPortal, you can use the default pin settings. # Leave this DEFAULT line uncommented. # If you are using a board with pre-defined ESP32 Pins: esp32 = ESP32() # If you are using a Metro M7 **OR** # if you are using CircuitPython 6.0.0 or earlier, # on PyPortal and PyPortal Titano only, use the pin settings # below. Comment out the DEFAULT line above and uncomment # the line below. For CircuitPython 6.1.0, the pin names # have changed for these boards, and the DEFAULT line # above is correct. # esp32 = ESP32(tx=board.TX, rx=board.RX) # If you are using an AirLift FeatherWing or AirLift Bitsy Add-On, # use the pin settings below. Comment out the DEFAULT line above # and uncomment the lines below. # If you are using an AirLift Breakout, check that these # choices match the wiring to your microcontroller board, # or change them as appropriate. # esp32 = ESP32( # reset=board.D12, # gpio0=board.D10, # busy=board.D11, # chip_select=board.D13, # tx=board.TX, # rx=board.RX, # ) # If you are using an AirLift Shield, # use the pin settings below. Comment out the DEFAULT line above # and uncomment the lines below. # esp32 = ESP32( # reset=board.D5, # gpio0=board.D6, # busy=board.D7, # chip_select=board.D10, # tx=board.TX, # rx=board.RX, # ) adapter = esp32.start_bluetooth() ble = BLERadio(adapter) uart = UARTService() advertisement = ProvideServicesAdvertisement(uart) while True: ble.start_advertising(advertisement) print("waiting to connect") while not ble.connected: pass print("connected: trying to read input") while ble.connected: # Returns b'' if nothing was read. one_byte = uart.read(1) if one_byte: print(one_byte) uart.write(one_byte)
Talk to the AirLift via the Bluefruit LE Connect App
Start the Bluefruit LE Connect App on your phone or tablet. You should see a CIRCUITPY device available to connect to. Tap the Connect button (1):
You'll then see a list of Bluefruit Connect functions ("modules"). Choose the UART module (2):
On the UART module page, you can type a string and press Send (3). You'll see that string entered, and then see it echoed back (echoing is in gray).
Text editor powered by tinymce.