Install CircuitPython
This guide assumes that you've gotten your Raspberry Pi up and running, and have CircuitPython installed. If not, check out the guide:
To install the library for the Pi OLED, enter the following into the terminal:
sudo pip3 install adafruit-circuitpython-ssd1305
If that complains about pip3 not being installed, then run this first to install it:
sudo apt-get install python3-pip
We also need PIL to allow using text with custom fonts. There are several system libraries that PIL relies on, so installing via a package manager is the easiest way to bring in everything:
sudo apt-get install python3-pil
Enable I2C
To enable i2c, you can follow our detailed guide on configuring the Pi with I2C support here.
After you've enabled I2C you will need to shutdown with sudo shutdown -h now
Once the Pi has halted, plug in the PiOLED. Now you can power the Pi back up, and log back in. Run the following command from a terminal prompt to scan/detect the I2C devices
sudo i2cdetect -y 1
You should see the following, indicating that address 0x3c (the OLED display) was found
Verify I2C Device
You can run our stats example, which will query the Pi for details on CPU load, disk space, etc. and print it on the OLED.
Create a new file with nano ~pi/stats.py and paste this code below in! Then save it.
# SPDX-FileCopyrightText: <text> 2020 Tony DiCola, James DeVito, # and 2020 Melissa LeBlanc-Williams, for Adafruit Industries </text> # SPDX-License-Identifier: MIT # This example is for use on (Linux) computers that are using CPython with # Adafruit Blinka to support CircuitPython libraries. CircuitPython does # not support PIL/pillow (python imaging library)! import time import subprocess from board import SCL, SDA, D4 import busio import digitalio from PIL import Image, ImageDraw, ImageFont import adafruit_ssd1305 # Define the Reset Pin oled_reset = digitalio.DigitalInOut(D4) # Create the I2C interface. i2c = busio.I2C(SCL, SDA) # Create the SSD1305 OLED class. # The first two parameters are the pixel width and pixel height. Change these # to the right size for your display! disp = adafruit_ssd1305.SSD1305_I2C(128, 32, i2c, reset=oled_reset) # Clear display. disp.fill(0) disp.show() # Create blank image for drawing. # Make sure to create image with mode '1' for 1-bit color. width = disp.width height = disp.height image = Image.new("1", (width, height)) # Get drawing object to draw on image. draw = ImageDraw.Draw(image) # Draw a black filled box to clear the image. draw.rectangle((0, 0, width, height), outline=0, fill=0) # Draw some shapes. # First define some constants to allow easy resizing of shapes. padding = -2 top = padding bottom = height - padding # Move left to right keeping track of the current x position for drawing shapes. x = 0 # Load default font. font = ImageFont.load_default() # Alternatively load a TTF font. Make sure the .ttf font file is in the # same directory as the python script! # Some other nice fonts to try: http://www.dafont.com/bitmap.php # font = ImageFont.truetype('/usr/share/fonts/truetype/dejavu/DejaVuSans.ttf', 9) while True: # Draw a black filled box to clear the image. draw.rectangle((0, 0, width, height), outline=0, fill=0) # Shell scripts for system monitoring from here: # https://unix.stackexchange.com/questions/119126/command-to-display-memory-usage-disk-usage-and-cpu-load cmd = "hostname -I | cut -d' ' -f1" IP = subprocess.check_output(cmd, shell=True).decode("utf-8") cmd = "top -bn1 | grep load | awk '{printf \"CPU Load: %.2f\", $(NF-2)}'" CPU = subprocess.check_output(cmd, shell=True).decode("utf-8") cmd = "free -m | awk 'NR==2{printf \"Mem: %s/%s MB %.2f%%\", $3,$2,$3*100/$2 }'" MemUsage = subprocess.check_output(cmd, shell=True).decode("utf-8") cmd = 'df -h | awk \'$NF=="/"{printf "Disk: %d/%d GB %s", $3,$2,$5}\'' Disk = subprocess.check_output(cmd, shell=True).decode("utf-8") # Write four lines of text. draw.text((x, top + 0), "IP: " + IP, font=font, fill=255) draw.text((x, top + 8), CPU, font=font, fill=255) draw.text((x, top + 16), MemUsage, font=font, fill=255) draw.text((x, top + 25), Disk, font=font, fill=255) # Display image. disp.image(image) disp.show() time.sleep(0.1)
Run sudo python3 stats.py
and you should see something like the following image:
Running Stats on Boot
You can pretty easily make it so this handy program runs every time you boot your Pi.
The fastest/easiest way is to put it in /etc/rc.local
Run sudo nano /etc/rc.local and add the line
sudo python3 /home/pi/stats.py &
on its own line right before exit 0
Then save and exit. Reboot to verify that the screen comes up on boot!
Library Usage
In the examples subdirectory of the Adafruit_CircuitPython_SSD1305 repository, you'll find examples which demonstrate the usage of the library.
To help you get started, I'll walk you through the stats.py code you ran earlier, that way you can use this file as a basis of a future project.
import time import subprocess from board import SCL, SDA, D4 import busio import digitalio from PIL import Image, ImageDraw, ImageFont import adafruit_ssd1305
First, a few Python modules are imported. This includes the adafruit_ssd1305
module which contains the OLED driver classes.
To draw images, shapes, and text/fonts, the code imports some of the Python Imaging Library's modules like Image
, ImageDraw
, and ImageFont
.
# Define the Reset Pin oled_reset = digitalio.DigitalInOut(D4) # Create the I2C interface. i2c = busio.I2C(SCL, SDA) # Create the SSD1305 OLED class. # The first two parameters are the pixel width and pixel height. Change these # to the right size for your display! disp = adafruit_ssd1305.SSD1305_I2C(128, 32, i2c, reset=oled_reset)
Since the PiOLED is a 128x32 I2C only device, the screen size, reset pin, and the i2c interface are passed to the adafruit_ssd.SSD1305_I2C
class.
# Clear display. disp.fill(0) disp.show() # Create blank image for drawing. # Make sure to create image with mode '1' for 1-bit color. width = disp.width height = disp.height image = Image.new('1', (width, height)) # Get drawing object to draw on image. draw = ImageDraw.Draw(image) # Draw a black filled box to clear the image. draw.rectangle((0, 0, width, height), outline=0, fill=0)
The next chunk of code clears the display by inverting its fill with fill(0)
and then writing to the display with show()
.
Then it will configure a PIL drawing class to prepare for drawing graphics. Notice that the image buffer is created in 1-bit mode with the '1'
parameter, this is important because the display only supports black and white colors.
We then re-draw a large black rectangle to clear the screen. In theory we don't have to clear the screen again, but its a good example of how to draw a shape!
# Draw some shapes. # First define some constants to allow easy resizing of shapes. padding = -2 top = padding bottom = height-padding # Move left to right keeping track of the current x position for drawing shapes. x = 0 # Load default font. font = ImageFont.load_default() # Alternatively load a TTF font. Make sure the .ttf font file is in the # same directory as the python script! # Some other nice fonts to try: http://www.dafont.com/bitmap.php #font = ImageFont.truetype('/usr/share/fonts/truetype/dejavu/DejaVuSans.ttf', 9)
Once the display is initialized and a drawing object is prepared, you can draw shapes, text and graphics using PIL's drawing commands. We'll define some constraints based on the height and width of the display to allow for easy resizing of shapes.
Then, the code loads the default
font, which works fine, but there's other fonts you can load.
Next the code loads a built-in default font and draws a few lines of text. You can also load your own TrueType font and use it to render fancy text in any style you like
while True: # Draw a black filled box to clear the image. draw.rectangle((0, 0, width, height), outline=0, fill=0) # Shell scripts for system monitoring from here: # https://unix.stackexchange.com/questions/119126/command-to-display-memory-usage-disk-usage-and-cpu-load cmd = "hostname -I | cut -d\' \' -f1" IP = subprocess.check_output(cmd, shell=True).decode("utf-8") cmd = "top -bn1 | grep load | awk '{printf \"CPU Load: %.2f\", $(NF-2)}'" CPU = subprocess.check_output(cmd, shell=True).decode("utf-8") cmd = "free -m | awk 'NR==2{printf \"Mem: %s/%s MB %.2f%%\", $3,$2,$3*100/$2 }'" MemUsage = subprocess.check_output(cmd, shell=True).decode("utf-8") cmd = "df -h | awk '$NF==\"/\"{printf \"Disk: %d/%d GB %s\", $3,$2,$5}'" Disk = subprocess.check_output(cmd, shell=True).decode("utf-8") # Write four lines of text. draw.text((x, top+0), "IP: "+IP, font=font, fill=255) draw.text((x, top+8), CPU, font=font, fill=255) draw.text((x, top+16), MemUsage, font=font, fill=255) draw.text((x, top+25), Disk, font=font, fill=255) # Display image. disp.image(image) disp.show() time.sleep(.1)
Using the subprocess class, python can utilize linux commands to access the Pi's system information. This loop updates the screen at 10 times a second.
That's all there is to the stats.py code!
Speeding up the Display
For the best performance, especially if you are doing fast animations, you'll want to tweak the I2C core to run at 1MHz. By default it may be 100KHz or 400KHz
To do this edit the config with sudo nano /boot/config.txt
and add to the end of the file
dtparam=i2c_baudrate=1000000
Page last edited January 22, 2025
Text editor powered by tinymce.