# 2.2" TFT Display ## Overview ![](https://cdn-learn.adafruit.com/assets/assets/000/049/581/medium800/arduino_compatibles_1480-00.jpg?1513980592) This lovely little display breakout is the best way to add a small, colorful and bright display to any project. Since the display uses 4-wire SPI to communicate and has its own pixel-addressable frame buffer, it can be used with every kind of microcontroller. Even a very small one with low memory and few pins available! Warning: ![eyespi](https://cdn-shop.adafruit.com/970x728/1480-12.jpg ) This display comes with an EYESPI connector! This 18-pin 0.5mm pitch FPC connector has a flip-top connector for using a flex cable to hook up your display. It enables you to avoid soldering and get your display up off of the breadboard! Consider it a sort of "STEMMA QT for displays" - a way to quickly connect and extend display wiring that uses a lot of SPI pins. It also allows for communicating with displays over longer distances. The [EYESPI flex cables](https://www.adafruit.com/?q=eyespi+cable&sort=BestMatch) are available in multiple lengths to suit any project. This is especially useful for projects where you want your display mounted separate from your microcontroller. ![](https://cdn-learn.adafruit.com/assets/assets/000/049/582/medium800/arduino_compatibles_rects.jpg?1513980688) The 2.2" display has 320x240 color pixels. Unlike the low cost "Nokia 6110" and similar LCD displays, which are CSTN type and thus have poor color and slow refresh, this display is a true TFT! The TFT driver (ILI9340) can display full 16-bit color. And the LCD will always come with the same driver chip so there's no worries that your code will not work from one to the other. ![sd](https://cdn-shop.adafruit.com/970x728/1480-13.jpg ) The breakout has the TFT display soldered on (it uses a delicate flex-circuit connector) as well as a ultra-low-dropout 3.3V regulator and a 3/5V level shifter so you can use it with 3.3V or 5V power and logic. We also had a little space so we placed a microSD card holder so you can easily load full color bitmaps from a FAT16/FAT32 formatted microSD card. The microSD card is not included [but you can pick one up here](http://www.adafruit.com/products/102 "Link: http://www.adafruit.com/products/102"). - [Next Page](https://learn.adafruit.com/2-2-tft-display/pinouts.md) ## Featured Products ### 2.2" 18-bit color TFT LCD display with microSD card breakout [2.2" 18-bit color TFT LCD display with microSD card breakout](https://www.adafruit.com/product/1480) This lovely little display breakout is the best way to add a small, colorful, and bright display to any project. Since the display uses 4-wire SPI to communicate and has its own pixel-addressable frame buffer, it can be used with every kind of microcontroller. Even a very small one with low... Out of Stock [Buy Now](https://www.adafruit.com/product/1480) [Related Guides to the Product](https://learn.adafruit.com/products/1480/guides) ### Breadboarding wire bundle [Breadboarding wire bundle](https://www.adafruit.com/product/153) 75 flexible stranded core wires with stiff ends molded on in red, orange, yellow, green, blue, brown, black and white. These are a major improvement over the "box of bent wires" that are sometimes sold with breadboards, and faster than stripping your own solid core wires. Makes... In Stock [Buy Now](https://www.adafruit.com/product/153) [Related Guides to the Product](https://learn.adafruit.com/products/153/guides) ### Adafruit METRO 328 Fully Assembled - Arduino IDE compatible [Adafruit METRO 328 Fully Assembled - Arduino IDE compatible](https://www.adafruit.com/product/50) We sure love the ATmega328 here at Adafruit, and we use them _a lot_ for our own projects. The processor has plenty of GPIO, Analog inputs, hardware UART SPI and I2C, timers and PWM galore - just enough for most simple projects. When we need to go small, we use a Out of Stock [Buy Now](https://www.adafruit.com/product/50) [Related Guides to the Product](https://learn.adafruit.com/products/50/guides) ### Half Sized Premium Breadboard - 400 Tie Points [Half Sized Premium Breadboard - 400 Tie Points](https://www.adafruit.com/product/64) This is a cute, half-size breadboard with 400 tie points, good for small projects. It's 3.25" x 2.2" / 8.3cm x 5.5cm with a standard double-strip in the middle and two power rails on both sides. You can pull the power rails off easily to make the breadboard as... Out of Stock [Buy Now](https://www.adafruit.com/product/64) [Related Guides to the Product](https://learn.adafruit.com/products/64/guides) ## Related Guides - [Circuit Playground: D is for Diode](https://learn.adafruit.com/circuit-playground-d-is-for-diode.md) - [Making Adabot: Part 2](https://learn.adafruit.com/making-adabot-part-2.md) - [DS1307 Real Time Clock Breakout Board Kit](https://learn.adafruit.com/ds1307-real-time-clock-breakout-board-kit.md) - [Bluefruit LE Connect for iOS and Android](https://learn.adafruit.com/bluefruit-le-connect.md) - [Halloween Pumpkin](https://learn.adafruit.com/halloween-pumpkin.md) - [Adafruit 4-Channel ADC Breakouts](https://learn.adafruit.com/adafruit-4-channel-adc-breakouts.md) - [Arduino "Hunt The Wumpus"](https://learn.adafruit.com/arduino-hunt-the-wumpus.md) - [Tiny Arduino Music Visualizer](https://learn.adafruit.com/piccolo.md) - [Automatic Monitor Color Temperature Adjustment](https://learn.adafruit.com/automatic-monitor-color-temperature-adjustment.md) - [Arduino Lesson 7. Make an RGB LED Fader](https://learn.adafruit.com/adafruit-arduino-lesson-7-make-an-rgb-led-fader.md) - [Arduino Lesson 17. Email Sending Movement Detector](https://learn.adafruit.com/arduino-lesson-17-email-sending-movement-detector.md) - [Skill Badge Requirements: Microcontrollers](https://learn.adafruit.com/skill-badge-requirements-microcontrollers.md) - [Create an Internet of Things Dashboard with Adafruit IO](https://learn.adafruit.com/create-an-internet-of-things-dashboard-with-adafruit-dot-io.md) - [Arduino Lesson 15. DC Motor Reversing](https://learn.adafruit.com/adafruit-arduino-lesson-15-dc-motor-reversing.md) - [WiFi Controlled Mobile Robot](https://learn.adafruit.com/wifi-controlled-mobile-robot.md)